mcAfee Secure Website
exam =5
exam =6

Exam Code: JN0-650

Exam Name: Enterprise Routing and Switching, Professional (JNCIP-ENT)

Certification Provider: Juniper

Corresponding Certification: JNCIP-ENT

Juniper JN0-650 Questions & Answers

Reliable & Actual Study Materials for JN0-650 Exam Success

107 Questions & Answers with Testing Engine

"JN0-650: Enterprise Routing and Switching, Professional (JNCIP-ENT)" Testing Engine covers all the knowledge points of the real Juniper JN0-650 exam.

The latest actual JN0-650 Questions & Answers from Pass4sure. Everything you need to prepare and get best score at JN0-650 exam easily and quickly.

exam =7
Guarantee

Satisfaction Guaranteed

Pass4sure has a remarkable Juniper Candidate Success record. We're confident of our products and provide no hassle product exchange. That's how confident we are!

99.3% Pass Rate
Was: $137.49
Now: $124.99

Juniper JN0-650 Practice Test 8

Question 70

At a large enterprise updating redundant switch links, a Junos specialist investigates this scenario: An access switch unexpectedly becomes the root bridge and traffic takes a slow path through the campus. The change must retain both link resilience and correct VLAN isolation. Which operational change most directly resolves the observed failure?

  1. Align the MSTP region attributes and intended VLAN mappings across the switches.
  2. Set supported bridge priorities so designated distribution switches become root and backup root.
  3. Increase supported link MTU consistently or adjust customer frame limits where required.
  4. Enable a consistent MSTP topology and verify the expected alternate-port state.

Explanation

Correct Answer

B:

For a large enterprise updating redundant switch links, the direct corrective action is: Set supported bridge priorities so designated distribution switches become root and backup root. This addresses the mechanism: Spanning-tree root selection uses bridge identifiers and configured priorities within the relevant instance. Confirm by checking: show spanning-tree bridge identifies the intended root for each MST instance. During rollout, preserve redundant root placement and test topology changes outside production peaks.

Incorrect Answers

A:

MSTP region membership depends on compatible region name, revision and VLAN-to-instance mapping digest. The appropriate correction for the reported case is: Set supported bridge priorities so designated distribution switches become root and backup root.

C:

Adding an outer VLAN tag increases Ethernet frame size and may exceed an interface's supported MTU. Fixing that different mechanism would not address the current root cause: spanning-tree root selection uses bridge identifiers and configured priorities within the relevant instance.

D:

Spanning tree prevents bridging loops by keeping appropriate redundant ports in nondesignated states. Its verification is distinct from the reported condition: An access switch unexpectedly becomes the root bridge and traffic takes a slow path through the campus. The change must retain both link resilience and correct VLAN isolation.

Question 71

At a provider Ethernet network carrying customer Layer 2 services, a Junos specialist investigates this scenario: A service provider must carry identical customer VLAN IDs from different tenants without mixing their traffic. The service must preserve tags without bridging unrelated tenants. Which operational result would most clearly confirm the fix?

  1. The aggregate reports active members and traffic survives loss of one constituent link.
  2. Maximum expected tagged frames traverse every provider hop without oversize drops.
  3. Captures show preserved inner customer tags inside the expected outer service tag.
  4. Customer control frames arrive at the remote customer edge without altering provider bridge state.

Explanation

Correct Answer

C:

For a provider Ethernet network carrying customer Layer 2 services, the decisive evidence is: Captures show preserved inner customer tags inside the expected outer service tag. This validates the action: Configure supported provider bridging with a distinct service tag for each tenant context. Because: IEEE 802.1ad Q-in-Q encapsulates customer-tagged frames with an outer service VLAN tag. An unrelated successful test would not prove this specific issue is resolved.

Incorrect Answers

A:

A link aggregation group presents multiple member links as one logical Ethernet interface when both peers agree. The appropriate correction for the reported case is: Configure supported provider bridging with a distinct service tag for each tenant context.

B:

Adding an outer VLAN tag increases Ethernet frame size and may exceed an interface's supported MTU. Fixing that different mechanism would not address the current root cause: IEEE 802.1ad Q-in-Q encapsulates customer-tagged frames with an outer service VLAN tag.

D:

Layer 2 protocol tunneling can transport specified customer control frames across a separate provider bridging domain. Its verification is distinct from the reported condition: A service provider must carry identical customer VLAN IDs from different tenants without mixing their traffic. The service must preserve tags without bridging unrelated tenants.

Question 72

At an enterprise replacing legacy IP handsets, a Junos specialist investigates this scenario: A high-capacity phone reports insufficient power even though the switch's overall power budget is adequate. The team must check phone support and PoE capacity before cutover. Which response best restores the intended behavior?

  1. Verify total PoE capacity and allocate sufficient per-port power for the installed phones.
  2. Publish the intended LLDP-MED voice network policy on the switch access port.
  3. Enable supported LLDP on authorized interfaces and inspect neighbor information.
  4. Check LLDP-MED power negotiation and available power on the phone's switch interface.

Explanation

Correct Answer

D:

For an enterprise replacing legacy IP handsets, the direct corrective action is: Check LLDP-MED power negotiation and available power on the phone's switch interface. This addresses the mechanism: Supported LLDP-MED or LLDP power TLVs can negotiate endpoint power requirements beyond static class assumptions. Confirm by checking: Switch and phone agree on the needed power allocation and optional hardware stays enabled. During rollout, review platform limits before claiming all phone accessories can receive unlimited PoE.

Incorrect Answers

A:

PoE availability depends on available switch power budget and each attached device's negotiated consumption. The appropriate correction for the reported case is: Check LLDP-MED power negotiation and available power on the phone's switch interface.

B:

LLDP-MED network policy information can advertise voice VLAN and QoS settings to compatible phones. Fixing that different mechanism would not address the current root cause: supported LLDP-MED or LLDP power TLVs can negotiate endpoint power requirements beyond static class assumptions.

C:

Link Layer Discovery Protocol advertises local chassis and port information to directly attached compatible devices. Its verification is distinct from the reported condition: A high-capacity phone reports insufficient power even though the switch's overall power budget is adequate. The team must check phone support and PoE capacity before cutover.

Question 73

At a national enterprise designing OSPF between offices, a Junos specialist investigates this scenario: A branch area needs to redistribute local prefixes but must still avoid full external LSA flooding. The internal forwarding path must remain stable when one uplink fails. What would demonstrate a successful correction under test?

  1. The local type-7 advertisement appears and translated external reachability is available outside the NSSA.
  2. Area routers learn a usable default route without inappropriate external LSAs.
  3. The subnet is reachable from OSPF peers while no neighbor forms on the passive port.
  4. The expected interarea prefix LSA and remote IPv6 route appear in the intended area.

Explanation

Correct Answer

A:

For a national enterprise designing OSPF between offices, the decisive evidence is: The local type-7 advertisement appears and translated external reachability is available outside the NSSA. This validates the action: Configure a consistent NSSA area and permitted redistribution at the branch ASBR. Because: A not-so-stubby area allows local external routes using type-7 LSAs and an ABR can translate them toward other areas. An unrelated successful test would not prove this specific issue is resolved.

Incorrect Answers

B:

A conventional stub area limits external LSAs and uses a suitable default route for outside reachability. The appropriate correction for the reported case is: Configure a consistent NSSA area and permitted redistribution at the branch ASBR.

C:

A passive OSPF interface can advertise attached reachability while suppressing neighbor-discovery Hellos. Fixing that different mechanism would not address the current root cause: a not-so-stubby area allows local external routes using type-7 LSAs and an ABR can translate them toward other areas.

D:

OSPFv3 interarea-prefix LSAs convey reachable IPv6 prefixes across area boundaries. Its verification is distinct from the reported condition: A branch area needs to redistribute local prefixes but must still avoid full external LSA flooding. The internal forwarding path must remain stable when one uplink fails.

Question 74

At a national enterprise designing OSPF between offices, a Junos specialist investigates this scenario: An OSPFv3 ABR has an IPv6 subnet internally but other areas never learn the prefix. The internal forwarding path must remain stable when one uplink fails. When would the described mechanism be appropriate?

  1. Use link-local addressing to interpret OSPFv3 IPv6 neighbor and next-hop behavior.
  2. Use interarea-prefix LSAs to propagate IPv6 reachability between OSPFv3 areas.
  3. Use OSPFv3 for link-state routing of eligible IPv6 enterprise prefixes.
  4. Prefer type-1 external metrics where internal distance to the ASBR must influence selection.

Explanation

Correct Answer

B:

For a national enterprise designing OSPF between offices, this mechanism fits the requirement: Use interarea-prefix LSAs to propagate IPv6 reachability between OSPFv3 areas. The design is appropriate because: OSPFv3 interarea-prefix LSAs convey reachable IPv6 prefixes across area boundaries. In this scenario, the observed issue is: An OSPFv3 ABR has an IPv6 subnet internally but other areas never learn the prefix. The corresponding implementation is: Check ABR area topology and permitted interarea prefix advertisement for the missing network.

Incorrect Answers

A:

OSPFv3 neighbor exchanges and next-hop forwarding commonly use IPv6 link-local addresses on the adjoining link. The appropriate correction for the reported case is: Check ABR area topology and permitted interarea prefix advertisement for the missing network.

C:

OSPFv3 is a distinct link-state protocol requiring correct interface and area enablement for IPv6 environments. Fixing that different mechanism would not address the current root cause: OSPFv3 interarea-prefix LSAs convey reachable IPv6 prefixes across area boundaries.

D:

Type-1 external OSPF cost includes internal cost to the ASBR while type-2 primarily uses the external metric for selection. Its verification is distinct from the reported condition: An OSPFv3 ABR has an IPv6 subnet internally but other areas never learn the prefix. The internal forwarding path must remain stable when one uplink fails. When would the described mechanism be appropriate.

Question 75

At a managed network team troubleshooting an internet edge, a Junos specialist investigates this scenario: An iBGP speaker advertises a learned external prefix but internal clients cannot reach the external provider next hop. The diagnosis must distinguish a healthy BGP session from eligible received routes. What protocol behavior accounts for this failure?

  1. BGP AS-path loop detection normally prevents accepting routes already traversing the local autonomous system.
  2. BGP MED can signal a preferred ingress point to a neighboring AS subject to the neighbor's selection policy.
  3. iBGP propagation may retain the original eBGP next-hop attribute unless policy or configuration changes it.
  4. A usable BGP route requires an eligible reachable forwarding next hop before it can become active.

Explanation

Correct Answer

C:

For a managed network team troubleshooting an internet edge, the governing mechanism is: iBGP propagation may retain the original eBGP next-hop attribute unless policy or configuration changes it. It explains the reported symptom: An iBGP speaker advertises a learned external prefix but internal clients cannot reach the external provider next hop. The intended response is: Apply approved next-hop self behavior at the correct iBGP advertisement boundary. Verification: Internal routers resolve the advertised next hop through the enterprise IGP and can forward to the prefix.

Incorrect Answers

A:

BGP AS-path loop detection normally prevents accepting routes already traversing the local autonomous system. This alternative mechanism does not match the current fault.

B:

BGP MED can signal a preferred ingress point to a neighboring AS subject to the neighbor's selection policy. Fixing that different mechanism would not address the current root cause: iBGP propagation may retain the original eBGP next-hop attribute unless policy or configuration changes it.

D:

A usable BGP route requires an eligible reachable forwarding next hop before it can become active. Its verification is distinct from the reported condition: An iBGP speaker advertises a learned external prefix but internal clients cannot reach the external provider next hop. The diagnosis must distinguish a healthy BGP session from eligible received routes.

Question 76

At a data-center access fabric using tagged trunks, a Junos specialist investigates this scenario: A unicast frame is flooded across a VLAN because the switch lacks a destination MAC entry. The proposed behavior must be validated on actual switching ports. Which technical mechanism most directly explains the symptom?

  1. Adding an outer VLAN tag increases Ethernet frame size and may exceed an interface's supported MTU.
  2. An Ethernet trunk carries selected tagged VLANs and membership must include every allowed VLAN.
  3. A link aggregation group presents multiple member links as one logical Ethernet interface when both peers agree.
  4. Layer 2 switches learn source MAC addresses on ingress ports and forward known unicast using their MAC tables.

Explanation

Correct Answer

D:

For a data-center access fabric using tagged trunks, the governing mechanism is: Layer 2 switches learn source MAC addresses on ingress ports and forward known unicast using their MAC tables. It explains the reported symptom: A unicast frame is flooded across a VLAN because the switch lacks a destination MAC entry. The intended response is: Verify MAC learning and the relevant source port/VLAN association. Verification: show ethernet-switching table contains the expected MAC-to-port entry and forwarding becomes selective.

Incorrect Answers

A:

Adding an outer VLAN tag increases Ethernet frame size and may exceed an interface's supported MTU. This alternative mechanism does not match the current fault.

B:

An Ethernet trunk carries selected tagged VLANs and membership must include every allowed VLAN. Fixing that different mechanism would not address the current root cause: layer 2 switches learn source MAC addresses on ingress ports and forward known unicast using their MAC tables.

C:

A link aggregation group presents multiple member links as one logical Ethernet interface when both peers agree. Its verification is distinct from the reported condition: A unicast frame is flooded across a VLAN because the switch lacks a destination MAC entry. The proposed behavior must be validated on actual switching ports.

Question 77

At a large organization using Junos route reflectors, a Junos specialist investigates this scenario: An enterprise receives multiple paths from one neighboring AS and wants to influence which entry that AS uses. The change must not introduce an unwanted autonomous-system route leak. What important rollout safeguard is most relevant here?

  1. Do not assume a remote AS must honor MED or compare MED across all unrelated ASes.
  2. Do not claim origin always wins over local preference or AS-path length.
  3. Account for protocol default export rules and route activity before assuming all table entries advertise.
  4. Base limits on planned growth and supportable recovery actions rather than an arbitrary tiny threshold.

Explanation

Correct Answer

A:

For a large organization using Junos route reflectors, the relevant safeguard is: Do not assume a remote AS must honor MED or compare MED across all unrelated ASes. It matters while implementing: Apply intended MED values for comparable advertisements and validate the peer's MED treatment. The fault involves: BGP MED can signal a preferred ingress point to a neighboring AS subject to the neighbor's selection policy. The required acceptance result remains: The cooperating neighbor selects the intended ingress for otherwise matching routes.

Incorrect Answers

B:

BGP best-path selection considers origin type after higher-priority attributes, normally preferring IGP over EGP over incomplete. The appropriate correction for the reported case is: Do not assume a remote AS must honor MED or compare MED across all unrelated ASes.

C:

BGP export policy controls which eligible active routes the speaker announces to selected neighbors. Fixing that different mechanism would not address the current root cause: BGP MED can signal a preferred ingress point to a neighboring AS subject to the neighbor's selection policy.

D:

A BGP prefix-limit control detects or constrains excessive received NLRI from a peer. Its verification is distinct from the reported condition: An enterprise receives multiple paths from one neighboring AS and wants to influence which entry that AS uses. The change must not introduce an unwanted autonomous-system route leak.

Question 78

At an enterprise migrating virtual machines between racks, a Junos specialist investigates this scenario: A remote VTEP cannot locate a host MAC in another VXLAN segment even though the BGP EVPN session is established. The overlay must relearn host reachability without stale tunnel selection. What is the most likely design-related cause?

  1. EVPN Ethernet Auto-Discovery route type 1 participates in multihoming reachability and mass-withdraw behavior.
  2. EVPN route type 2 advertises MAC reachability and can include associated IP information for hosts.
  3. EVPN all-active multihoming permits multiple PEs to forward eligible known-unicast traffic with appropriate control-plane loop prevention.
  4. EVPN route type 5 conveys IP prefix reachability and can support routed overlay designs.

Explanation

Correct Answer

B:

For an enterprise migrating virtual machines between racks, the governing mechanism is: EVPN route type 2 advertises MAC reachability and can include associated IP information for hosts. It explains the reported symptom: A remote VTEP cannot locate a host MAC in another VXLAN segment even though the BGP EVPN session is established. The intended response is: Verify the local MAC/IP advertisement and its acceptance through the correct EVPN instance. Verification: A remote EVPN MAC table resolves the host to the expected originating VTEP.

Incorrect Answers

A:

EVPN Ethernet Auto-Discovery route type 1 participates in multihoming reachability and mass-withdraw behavior. This alternative mechanism does not match the current fault.

C:

EVPN all-active multihoming permits multiple PEs to forward eligible known-unicast traffic with appropriate control-plane loop prevention. Fixing that different mechanism would not address the current root cause: EVPN route type 2 advertises MAC reachability and can include associated IP information for hosts.

D:

EVPN route type 5 conveys IP prefix reachability and can support routed overlay designs. Its verification is distinct from the reported condition: A remote VTEP cannot locate a host MAC in another VXLAN segment even though the BGP EVPN session is established. The overlay must relearn host reachability without stale tunnel selection.

Question 79

At a healthcare organization connecting redundant facilities, a Junos specialist investigates this scenario: OSPF automatically assigned metrics do not distinguish two high-speed interfaces at the intended precision. The correction must not expose administrative network prefixes. For which use case is this feature the best match?

  1. Use passive OSPF interfaces for stub LANs without routing neighbors.
  2. Use identical area configuration on directly adjacent OSPF participants.
  3. Use a consistent OSPF reference bandwidth to distinguish modern link capacities.
  4. Use NSSA when a limited external-route origin must exist inside an OSPF area.

Explanation

Correct Answer

C:

For a healthcare organization connecting redundant facilities, this mechanism fits the requirement: Use a consistent OSPF reference bandwidth to distinguish modern link capacities. The design is appropriate because: OSPF automatic cost derives from reference bandwidth, which must be planned consistently in the domain. In this scenario, the observed issue is: OSPF automatically assigned metrics do not distinguish two high-speed interfaces at the intended precision. The corresponding implementation is: Set a suitable reference bandwidth for automatic cost calculation on relevant OSPF speakers.

Incorrect Answers

A:

A passive OSPF interface can advertise attached reachability while suppressing neighbor-discovery Hellos. The appropriate correction for the reported case is: Set a suitable reference bandwidth for automatic cost calculation on relevant OSPF speakers.

B:

OSPF neighbors on a common link must agree on the area identifier used in Hello processing. Fixing that different mechanism would not address the current root cause: OSPF automatic cost derives from reference bandwidth, which must be planned consistently in the domain.

D:

A not-so-stubby area allows local external routes using type-7 LSAs and an ABR can translate them toward other areas. Its verification is distinct from the reported condition: OSPF automatically assigned metrics do not distinguish two high-speed interfaces at the intended precision. The correction must not expose administrative network prefixes.

Question 80

At an enterprise replacing legacy IP handsets, a Junos specialist investigates this scenario: A technician plugs a phone into the wrong switch port and cannot identify its actual neighbor from cabling records. The team must check phone support and PoE capacity before cutover. What is the most likely design-related cause?

  1. PoE availability depends on available switch power budget and each attached device's negotiated consumption.
  2. Voice VLAN tagging and QoS classification must be mapped to the correct switch forwarding treatment.
  3. LLDP-MED network policy information can advertise voice VLAN and QoS settings to compatible phones.
  4. Link Layer Discovery Protocol advertises local chassis and port information to directly attached compatible devices.

Explanation

Correct Answer

D:

For an enterprise replacing legacy IP handsets, the governing mechanism is: Link Layer Discovery Protocol advertises local chassis and port information to directly attached compatible devices. It explains the reported symptom: A technician plugs a phone into the wrong switch port and cannot identify its actual neighbor from cabling records. The intended response is: Enable supported LLDP on authorized interfaces and inspect neighbor information. Verification: show lldp neighbors identifies the intended adjacent device and receiving port.

Incorrect Answers

A:

PoE availability depends on available switch power budget and each attached device's negotiated consumption. This alternative mechanism does not match the current fault.

B:

Voice VLAN tagging and QoS classification must be mapped to the correct switch forwarding treatment. Fixing that different mechanism would not address the current root cause: Link Layer Discovery Protocol advertises local chassis and port information to directly attached compatible devices.

C:

LLDP-MED network policy information can advertise voice VLAN and QoS settings to compatible phones. Its verification is distinct from the reported condition: A technician plugs a phone into the wrong switch port and cannot identify its actual neighbor from cabling records. The team must check phone support and PoE capacity before cutover.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests