mcAfee Secure Website
exam =5
exam =6

Exam Code: JN0-650

Exam Name: Enterprise Routing and Switching, Professional (JNCIP-ENT)

Certification Provider: Juniper

Corresponding Certification: JNCIP-ENT

Juniper JN0-650 Questions & Answers

Reliable & Actual Study Materials for JN0-650 Exam Success

107 Questions & Answers with Testing Engine

"JN0-650: Enterprise Routing and Switching, Professional (JNCIP-ENT)" Testing Engine covers all the knowledge points of the real Juniper JN0-650 exam.

The latest actual JN0-650 Questions & Answers from Pass4sure. Everything you need to prepare and get best score at JN0-650 exam easily and quickly.

exam =7
Guarantee

Satisfaction Guaranteed

Pass4sure has a remarkable Juniper Candidate Success record. We're confident of our products and provide no hassle product exchange. That's how confident we are!

99.3% Pass Rate
Was: $137.49
Now: $124.99

Juniper JN0-650 Practice Test 75

Question 740

At a live-event venue using routed multicast streaming, a Junos specialist investigates this scenario: A new ASM sender transmits but remote receivers never learn about the source through their RP. The change must preserve source identity and avoid multicast loops. What protocol behavior accounts for this failure?

  1. PIM routers discover routing neighbors on participating interfaces through PIM Hello exchanges.
  2. Anycast RP permits multiple rendezvous points to share one RP address with routing choosing a reachable instance.
  3. (S,G) multicast state identifies one particular source S and destination group G.
  4. In PIM sparse-mode ASM, a first-hop designated router can register new source traffic with the RP.

Explanation

Correct Answer

D:

For a live-event venue using routed multicast streaming, the governing mechanism is: In PIM sparse-mode ASM, a first-hop designated router can register new source traffic with the RP. It explains the reported symptom: A new ASM sender transmits but remote receivers never learn about the source through their RP. The intended response is: Verify source-facing PIM DR behavior and reachability to the correct rendezvous point. Verification: The RP learns the source and joined downstream receivers begin receiving the stream.

Incorrect Answers

A:

PIM routers discover routing neighbors on participating interfaces through PIM Hello exchanges. This alternative mechanism does not match the current fault.

B:

Anycast RP permits multiple rendezvous points to share one RP address with routing choosing a reachable instance. Fixing that different mechanism would not address the current root cause: in PIM sparse-mode ASM, a first-hop designated router can register new source traffic with the RP.

C:

(S,G) multicast state identifies one particular source S and destination group G. Its verification is distinct from the reported condition: A new ASM sender transmits but remote receivers never learn about the source through their RP. The change must preserve source identity and avoid multicast loops.

Question 741

At a large organization using Junos route reflectors, a Junos specialist investigates this scenario: A BGP update is received but appears hidden because the announced next-hop address cannot be resolved in the routing table. The change must not introduce an unwanted autonomous-system route leak. Which configuration adjustment should be made first to address this issue?

  1. Repair the underlay route to the received BGP next hop or apply a deliberate next-hop policy.
  2. Apply approved next-hop self behavior at the correct iBGP advertisement boundary.
  3. Configure the intended inet-unicast family on the authorized BGP peering.
  4. Inspect show route hidden detail plus peer and policy diagnostics for the specific prefix.

Explanation

Correct Answer

A:

For a large organization using Junos route reflectors, the direct corrective action is: Repair the underlay route to the received BGP next hop or apply a deliberate next-hop policy. This addresses the mechanism: A usable BGP route requires an eligible reachable forwarding next hop before it can become active. Confirm by checking: show route hidden detail no longer reports an unreachable next hop and the prefix becomes eligible. During rollout, avoid setting next hop to self without confirming the chosen egress can actually forward the traffic.

Incorrect Answers

B:

IBGP propagation may retain the original eBGP next-hop attribute unless policy or configuration changes it. The appropriate correction for the reported case is: Repair the underlay route to the received BGP next hop or apply a deliberate next-hop policy.

C:

BGP NLRI family selection must include inet-unicast for eligible IPv4 unicast prefixes. Fixing that different mechanism would not address the current root cause: a usable BGP route requires an eligible reachable forwarding next hop before it can become active.

D:

Hidden and inactive BGP paths can result from next-hop resolution, policy rejection and competing path selection. Its verification is distinct from the reported condition: A BGP update is received but appears hidden because the announced next-hop address cannot be resolved in the routing table. The change must not introduce an unwanted autonomous-system route leak.

Question 742

At a campus network built with Juniper EX switches, a Junos specialist investigates this scenario: Two adjacent switches use MSTP but appear to occupy different regions despite a shared physical trunk. The intended segmentation and loop prevention must remain intact. Which technical mechanism most directly explains the symptom?

  1. A provider S-VLAN or equivalent encapsulation boundary is needed to keep identical customer C-VLAN numbers separate.
  2. MSTP region membership depends on compatible region name, revision and VLAN-to-instance mapping digest.
  3. Multiple Spanning Tree Protocol maps selected VLANs into common spanning-tree instances.
  4. IEEE 802.1ad Q-in-Q encapsulates customer-tagged frames with an outer service VLAN tag.

Explanation

Correct Answer

B:

For a campus network built with Juniper EX switches, the governing mechanism is: MSTP region membership depends on compatible region name, revision and VLAN-to-instance mapping digest. It explains the reported symptom: Two adjacent switches use MSTP but appear to occupy different regions despite a shared physical trunk. The intended response is: Align the MSTP region attributes and intended VLAN mappings across the switches. Verification: Operational state shows common region information and expected instance boundaries.

Incorrect Answers

A:

A provider S-VLAN or equivalent encapsulation boundary is needed to keep identical customer C-VLAN numbers separate. This alternative mechanism does not match the current fault.

C:

Multiple Spanning Tree Protocol maps selected VLANs into common spanning-tree instances. Fixing that different mechanism would not address the current root cause: MSTP region membership depends on compatible region name, revision and VLAN-to-instance mapping digest.

D:

IEEE 802.1ad Q-in-Q encapsulates customer-tagged frames with an outer service VLAN tag. Its verification is distinct from the reported condition: Two adjacent switches use MSTP but appear to occupy different regions despite a shared physical trunk. The intended segmentation and loop prevention must remain intact.

Question 743

At a regional provider operating Junos-based branch routers, a Junos specialist investigates this scenario: A remote router selects an external OSPF path unexpectedly because external metrics are compared differently. The team must validate neighbor state rather than assume basic IP reachability proves routing. What is the most appropriate correction to implement?

  1. Assign the connecting interfaces to the same intended OSPF area and validate the area boundary design.
  2. Configure a supported OSPF point-to-point network type consistently on the dedicated link.
  3. Choose the intended external metric type for the redistributed prefix and validate path selection.
  4. Align supported OSPF Hello and dead intervals on both neighboring interfaces.

Explanation

Correct Answer

C:

For a regional provider operating Junos-based branch routers, the direct corrective action is: Choose the intended external metric type for the redistributed prefix and validate path selection. This addresses the mechanism: Type-1 external OSPF cost includes internal cost to the ASBR while type-2 primarily uses the external metric for selection. Confirm by checking: Routes select the expected exit under different internal distances when tested. During rollout, avoid flipping E1 and E2 globally without analyzing alternate egress paths.

Incorrect Answers

A:

OSPF neighbors on a common link must agree on the area identifier used in Hello processing. The appropriate correction for the reported case is: Choose the intended external metric type for the redistributed prefix and validate path selection.

B:

OSPF interface network type influences neighbor formation and whether DR and BDR election is used. Fixing that different mechanism would not address the current root cause: type-1 external OSPF cost includes internal cost to the ASBR while type-2 primarily uses the external metric for selection.

D:

Neighbor compatibility depends on matching Hello and dead intervals for the participating link. Its verification is distinct from the reported condition: A remote router selects an external OSPF path unexpectedly because external metrics are compared differently. The team must validate neighbor state rather than assume basic IP reachability proves routing.

Question 744

At a national enterprise designing OSPF between offices, a Junos specialist investigates this scenario: A pair of OSPF speakers exchanges packets but reports timer mismatch and no stable adjacency. The internal forwarding path must remain stable when one uplink fails. Which configuration adjustment should be made first to address this issue?

  1. Create a tightly scoped policy matching the intended static prefix and apply it as an OSPF export policy.
  2. Configure a supported OSPF point-to-point network type consistently on the dedicated link.
  3. Enable OSPF on the intended logical interface under the appropriate area and confirm its interface parameters.
  4. Align supported OSPF Hello and dead intervals on both neighboring interfaces.

Explanation

Correct Answer

D:

For a national enterprise designing OSPF between offices, the direct corrective action is: Align supported OSPF Hello and dead intervals on both neighboring interfaces. This addresses the mechanism: Neighbor compatibility depends on matching Hello and dead intervals for the participating link. Confirm by checking: show ospf neighbor reaches Full and periodic Hellos remain within the agreed dead interval. During rollout, avoid shortening dead timers without checking CPU load and adjacent platform support.

Incorrect Answers

A:

Junos OSPF normally requires explicit export policy to redistribute eligible non-OSPF routes as external reachability. The appropriate correction for the reported case is: Align supported OSPF Hello and dead intervals on both neighboring interfaces.

B:

OSPF interface network type influences neighbor formation and whether DR and BDR election is used. Fixing that different mechanism would not address the current root cause: neighbor compatibility depends on matching Hello and dead intervals for the participating link.

C:

OSPF neighbor discovery requires the relevant logical interface to participate in the correct routing instance and area. Its verification is distinct from the reported condition: A pair of OSPF speakers exchanges packets but reports timer mismatch and no stable adjacency. The internal forwarding path must remain stable when one uplink fails.

Question 745

At a medical facility deploying high-power conference phones, a Junos specialist investigates this scenario: A newly connected desk phone remains in the data VLAN although the switch has a dedicated tagged voice VLAN. The phone network must retain appropriate VLAN and voice QoS treatment. Which limitation should guide the change control?

  1. Confirm phone model and manufacturer support instead of assuming all endpoints interpret MED TLVs.
  2. Do not exceed chassis supply or line-card power availability based only on per-port ratings.
  3. Check access policy and trunk tagging without granting the PC unauthorized voice-network privileges.
  4. Verify 802.1X and MAC RADIUS behavior separately for phone and PC identities.

Explanation

Correct Answer

A:

For a medical facility deploying high-power conference phones, the relevant safeguard is: Confirm phone model and manufacturer support instead of assuming all endpoints interpret MED TLVs. It matters while implementing: Publish the intended LLDP-MED voice network policy on the switch access port. The fault involves: LLDP-MED network policy information can advertise voice VLAN and QoS settings to compatible phones. The required acceptance result remains: The phone adopts the approved voice VLAN tag and registers using the expected voice network.

Incorrect Answers

B:

PoE availability depends on available switch power budget and each attached device's negotiated consumption. The appropriate correction for the reported case is: Confirm phone model and manufacturer support instead of assuming all endpoints interpret MED TLVs.

C:

A voice VLAN permits supported tagged phone traffic to use a separate VLAN from ordinary untagged data traffic. Fixing that different mechanism would not address the current root cause: LLDP-MED network policy information can advertise voice VLAN and QoS settings to compatible phones.

D:

An Ethernet phone can bridge tagged voice traffic and untagged workstation traffic with appropriate VLAN behavior. Its verification is distinct from the reported condition: A newly connected desk phone remains in the data VLAN although the switch has a dedicated tagged voice VLAN. The phone network must retain appropriate VLAN and voice QoS treatment.

Question 746

At a healthcare organization connecting redundant facilities, a Junos specialist investigates this scenario: OSPF automatically assigned metrics do not distinguish two high-speed interfaces at the intended precision. The correction must not expose administrative network prefixes. Which underlying distinction should guide troubleshooting?

  1. Junos OSPF normally requires explicit export policy to redistribute eligible non-OSPF routes as external reachability.
  2. OSPF automatic cost derives from reference bandwidth, which must be planned consistently in the domain.
  3. Link-state SPF recalculation is triggered by topology changes and must converge over a coherent LSDB.
  4. Junos OSPF export governs eligible external route origination while import filtering has different route-selection effects.

Explanation

Correct Answer

B:

For a healthcare organization connecting redundant facilities, the governing mechanism is: OSPF automatic cost derives from reference bandwidth, which must be planned consistently in the domain. It explains the reported symptom: OSPF automatically assigned metrics do not distinguish two high-speed interfaces at the intended precision. The intended response is: Set a suitable reference bandwidth for automatic cost calculation on relevant OSPF speakers. Verification: show ospf interface reports costs appropriate to the configured link speeds.

Incorrect Answers

A:

Junos OSPF normally requires explicit export policy to redistribute eligible non-OSPF routes as external reachability. This alternative mechanism does not match the current fault.

C:

Link-state SPF recalculation is triggered by topology changes and must converge over a coherent LSDB. Fixing that different mechanism would not address the current root cause: OSPF automatic cost derives from reference bandwidth, which must be planned consistently in the domain.

D:

Junos OSPF export governs eligible external route origination while import filtering has different route-selection effects. Its verification is distinct from the reported condition: OSPF automatically assigned metrics do not distinguish two high-speed interfaces at the intended precision. The correction must not expose administrative network prefixes.

Question 747

At a large organization using Junos route reflectors, a Junos specialist investigates this scenario: A BGP import policy changes but the operator wants to re-evaluate learned routes without tearing down a healthy peering. The change must not introduce an unwanted autonomous-system route leak. When would the described mechanism be appropriate?

  1. Use iBGP to distribute BGP-learned routes within one autonomous system.
  2. Use BGP export policy to restrict outbound network advertisements.
  3. Use route refresh for non-disruptive reevaluation of inbound BGP policy.
  4. Use BGP route reflectors to scale internal route distribution beyond a full mesh.

Explanation

Correct Answer

C:

For a large organization using Junos route reflectors, this mechanism fits the requirement: Use route refresh for non-disruptive reevaluation of inbound BGP policy. The design is appropriate because: BGP route refresh permits eligible peers to request readvertisement after policy changes when both support it. In this scenario, the observed issue is: A BGP import policy changes but the operator wants to re-evaluate learned routes without tearing down a healthy peering. The corresponding implementation is: Request a supported inbound route refresh for the affected peer after validating the new policy.

Incorrect Answers

A:

IBGP requires compatible local and remote AS settings, TCP reachability and correct neighbor addresses. The appropriate correction for the reported case is: Request a supported inbound route refresh for the affected peer after validating the new policy.

B:

BGP export policy controls which eligible active routes the speaker announces to selected neighbors. Fixing that different mechanism would not address the current root cause: BGP route refresh permits eligible peers to request readvertisement after policy changes when both support it.

D:

Ordinary iBGP split-horizon rules avoid re-advertising routes between iBGP peers; route reflectors provide controlled reflection. Its verification is distinct from the reported condition: A BGP import policy changes but the operator wants to re-evaluate learned routes without tearing down a healthy peering. The change must not introduce an unwanted autonomous-system route leak. When would the described mechanism be appropriate.

Question 748

At a financial services network enforcing trusted DSCP markings, a Junos specialist investigates this scenario: Junos CoS classifiers and schedulers are configured but packets continue to use unexpected default queues. Classification and downstream remarking must not be confused. Which limitation should guide the change control?

  1. Check both classification and rewrite stages because they solve different problems.
  2. Check percentages and priority interactions before promising absolute throughput for every burst.
  3. Do not trust unverified DSCP values from arbitrary user-controlled ports.
  4. Verify the actual output interface and aggregate hierarchy rather than binding a map to the wrong unit.

Explanation

Correct Answer

D:

For a financial services network enforcing trusted DSCP markings, the relevant safeguard is: Verify the actual output interface and aggregate hierarchy rather than binding a map to the wrong unit. It matters while implementing: Attach the intended scheduler map to the correct supported egress interface. The fault involves: A scheduler map must be associated with the appropriate interface for selected class-to-scheduler behavior. The required acceptance result remains: Interface queue statistics reflect the configured scheduler allocation under test.

Incorrect Answers

A:

Classification determines internal forwarding class while rewrite rules modify markings on outgoing packets. The appropriate correction for the reported case is: Verify the actual output interface and aggregate hierarchy rather than binding a map to the wrong unit.

B:

Junos schedulers control bandwidth allocation among queues using configured transmission rates and priorities. Fixing that different mechanism would not address the current root cause: a scheduler map must be associated with the appropriate interface for selected class-to-scheduler behavior.

C:

A behavior aggregate classifier maps incoming codepoint values to local forwarding class and loss priority. Its verification is distinct from the reported condition: Junos CoS classifiers and schedulers are configured but packets continue to use unexpected default queues. Classification and downstream remarking must not be confused.

Question 749

At a large organization using Junos route reflectors, a Junos specialist investigates this scenario: A BGP router has internal routes in its RIB but should advertise only an authorized subset to an external peer. The change must not introduce an unwanted autonomous-system route leak. What important rollout safeguard is most relevant here?

  1. Account for protocol default export rules and route activity before assuming all table entries advertise.
  2. Test term ordering and default policy behavior before enabling changes on a production peer.
  3. Coordinate secret rotations to avoid synchronized loss of redundant sessions.
  4. Do not treat a neighbor's Established state as proof that its prefixes were accepted.

Explanation

Correct Answer

A:

For a large organization using Junos route reflectors, the relevant safeguard is: Account for protocol default export rules and route activity before assuming all table entries advertise. It matters while implementing: Apply a narrowly matched export policy for intended prefixes to the relevant BGP group. The fault involves: BGP export policy controls which eligible active routes the speaker announces to selected neighbors. The required acceptance result remains: The peer receives only the approved announcements and no internal management subnets.

Incorrect Answers

B:

A BGP import policy determines which incoming route advertisements are accepted into the routing table. The appropriate correction for the reported case is: Account for protocol default export rules and route activity before assuming all table entries advertise.

C:

Compatible TCP-level BGP authentication methods can verify the configured neighbor relationship. Fixing that different mechanism would not address the current root cause: BGP export policy controls which eligible active routes the speaker announces to selected neighbors.

D:

Hidden and inactive BGP paths can result from next-hop resolution, policy rejection and competing path selection. Its verification is distinct from the reported condition: A BGP router has internal routes in its RIB but should advertise only an authorized subset to an external peer. The change must not introduce an unwanted autonomous-system route leak.

Question 750

At a healthcare organization connecting redundant facilities, a Junos specialist investigates this scenario: An OSPF stub area receives or expects external LSA behavior incompatible with its intended design. The correction must not expose administrative network prefixes. What risk must the implementation avoid?

  1. Do not confuse Junos route preference with the BGP LOCAL_PREF attribute.
  2. Do not make an ASBR-dependent area stub without checking redistribution requirements.
  3. Check address families and filtering carefully to avoid importing every static IPv6 route.
  4. Do not change the backbone area relationship without validating ABR connectivity.

Explanation

Correct Answer

B:

For a healthcare organization connecting redundant facilities, the relevant safeguard is: Do not make an ASBR-dependent area stub without checking redistribution requirements. It matters while implementing: Configure a compatible stub-area type throughout the area and validate ABR default behavior. The fault involves: A conventional stub area limits external LSAs and uses a suitable default route for outside reachability. The required acceptance result remains: Area routers learn a usable default route without inappropriate external LSAs.

Incorrect Answers

A:

Junos first chooses active routing-table entries using protocol route preference before forwarding installation. The appropriate correction for the reported case is: Do not make an ASBR-dependent area stub without checking redistribution requirements.

C:

Junos requires a suitable route export policy to originate eligible non-OSPFv3 routes. Fixing that different mechanism would not address the current root cause: a conventional stub area limits external LSAs and uses a suitable default route for outside reachability.

D:

OSPF neighbors on a common link must agree on the area identifier used in Hello processing. Its verification is distinct from the reported condition: An OSPF stub area receives or expects external LSA behavior incompatible with its intended design. The correction must not expose administrative network prefixes.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests