mcAfee Secure Website
exam =5
exam =6

Exam Code: JN0-650

Exam Name: Enterprise Routing and Switching, Professional (JNCIP-ENT)

Certification Provider: Juniper

Corresponding Certification: JNCIP-ENT

Juniper JN0-650 Questions & Answers

Reliable & Actual Study Materials for JN0-650 Exam Success

107 Questions & Answers with Testing Engine

"JN0-650: Enterprise Routing and Switching, Professional (JNCIP-ENT)" Testing Engine covers all the knowledge points of the real Juniper JN0-650 exam.

The latest actual JN0-650 Questions & Answers from Pass4sure. Everything you need to prepare and get best score at JN0-650 exam easily and quickly.

exam =7
Guarantee

Satisfaction Guaranteed

Pass4sure has a remarkable Juniper Candidate Success record. We're confident of our products and provide no hassle product exchange. That's how confident we are!

99.3% Pass Rate
Was: $137.49
Now: $124.99

Juniper JN0-650 Practice Test 61

Question 600

At an enterprise core exchanging BGP routes over redundant WAN paths, a Junos specialist investigates this scenario: A BGP neighbor is configured correctly but remains in Connect or Active state across a protected interconnect. The chosen route must have a valid data-plane next hop. Which underlying distinction should guide troubleshooting?

  1. Junos BGP best-path logic generally prefers the external route when preceding comparisons tie.
  2. A BGP import policy determines which incoming route advertisements are accepted into the routing table.
  3. Route-flap damping can suppress repeatedly changing paths according to configured penalties and reuse rules.
  4. BGP depends on a reachable TCP transport path, normally using destination port 179.

Explanation

Correct Answer

D:

For an enterprise core exchanging BGP routes over redundant WAN paths, the governing mechanism is: BGP depends on a reachable TCP transport path, normally using destination port 179. It explains the reported symptom: A BGP neighbor is configured correctly but remains in Connect or Active state across a protected interconnect. The intended response is: Check source reachability and permit the specifically authorized BGP TCP flow across the interconnect. Verification: The neighbor establishes its TCP session and BGP state changes to Established.

Incorrect Answers

A:

Junos BGP best-path logic generally prefers the external route when preceding comparisons tie. This alternative mechanism does not match the current fault.

B:

A BGP import policy determines which incoming route advertisements are accepted into the routing table. Fixing that different mechanism would not address the current root cause: BGP depends on a reachable TCP transport path, normally using destination port 179.

C:

Route-flap damping can suppress repeatedly changing paths according to configured penalties and reuse rules. Its verification is distinct from the reported condition: A BGP neighbor is configured correctly but remains in Connect or Active state across a protected interconnect. The chosen route must have a valid data-plane next hop.

Question 601

At an enterprise replacing legacy IP handsets, a Junos specialist investigates this scenario: A technician plugs a phone into the wrong switch port and cannot identify its actual neighbor from cabling records. The team must check phone support and PoE capacity before cutover. Which observation proves this requirement has been satisfied?

  1. show lldp neighbors identifies the intended adjacent device and receiving port.
  2. The phone stays powered under a representative simultaneous high-load endpoint test.
  3. The phone registers in the voice VLAN and the connected PC receives data-VLAN connectivity.
  4. Phone packets receive intended priority during congestion and desktop traffic cannot impersonate it.

Explanation

Correct Answer

A:

For an enterprise replacing legacy IP handsets, the decisive evidence is: show lldp neighbors identifies the intended adjacent device and receiving port. This validates the action: Enable supported LLDP on authorized interfaces and inspect neighbor information. Because: Link Layer Discovery Protocol advertises local chassis and port information to directly attached compatible devices. An unrelated successful test would not prove this specific issue is resolved.

Incorrect Answers

B:

PoE availability depends on available switch power budget and each attached device's negotiated consumption. The appropriate correction for the reported case is: Enable supported LLDP on authorized interfaces and inspect neighbor information.

C:

An Ethernet phone can bridge tagged voice traffic and untagged workstation traffic with appropriate VLAN behavior. Fixing that different mechanism would not address the current root cause: Link Layer Discovery Protocol advertises local chassis and port information to directly attached compatible devices.

D:

Voice VLAN tagging and QoS classification must be mapped to the correct switch forwarding treatment. Its verification is distinct from the reported condition: A technician plugs a phone into the wrong switch port and cannot identify its actual neighbor from cabling records. The team must check phone support and PoE capacity before cutover.

Question 602

At a service provider offering isolated VXLAN services, a Junos specialist investigates this scenario: A virtual machine moves between leaf switches but stale remote MAC advertisements keep traffic on the old VTEP. The engineer must verify both BGP EVPN signaling and underlay reachability. Which limitation should guide the change control?

  1. Validate split-horizon, DF and CE LAG behavior so redundancy does not create loops.
  2. Check duplicate-MAC protection to avoid interpreting a persistent Layer 2 loop as legitimate mobility.
  3. Check duplicate MAC and route-target behavior before forcing remote FDB entries.
  4. Constrain flooding domain and avoid replicating unknown unicast to unauthorized VTEPs.

Explanation

Correct Answer

B:

For a service provider offering isolated VXLAN services, the relevant safeguard is: Check duplicate-MAC protection to avoid interpreting a persistent Layer 2 loop as legitimate mobility. It matters while implementing: Verify advertisement and processing of the relevant MAC mobility extended community or sequence information. The fault involves: EVPN MAC mobility information can signal updated reachability and help distinguish a newer MAC location. The required acceptance result remains: Remote leaves update the affected MAC destination to the new VTEP after the controlled move.

Incorrect Answers

A:

EVPN all-active multihoming permits multiple PEs to forward eligible known-unicast traffic with appropriate control-plane loop prevention. The appropriate correction for the reported case is: Check duplicate-MAC protection to avoid interpreting a persistent Layer 2 loop as legitimate mobility.

C:

EVPN route type 2 advertises MAC reachability and can include associated IP information for hosts. Fixing that different mechanism would not address the current root cause: EVPN MAC mobility information can signal updated reachability and help distinguish a newer MAC location.

D:

EVPN route type 3 carries inclusive multicast Ethernet tag information used to establish BUM replication membership. Its verification is distinct from the reported condition: A virtual machine moves between leaf switches but stale remote MAC advertisements keep traffic on the old VTEP. The engineer must verify both BGP EVPN signaling and underlay reachability.

Question 603

At a managed network team troubleshooting an internet edge, a Junos specialist investigates this scenario: An enterprise wants to protect a BGP session from a spoofed adjacent TCP peer. The diagnosis must distinguish a healthy BGP session from eligible received routes. What protocol behavior accounts for this failure?

  1. Hidden and inactive BGP paths can result from next-hop resolution, policy rejection and competing path selection.
  2. iBGP requires compatible local and remote AS settings, TCP reachability and correct neighbor addresses.
  3. Compatible TCP-level BGP authentication methods can verify the configured neighbor relationship.
  4. A BGP prefix-limit control detects or constrains excessive received NLRI from a peer.

Explanation

Correct Answer

C:

For a managed network team troubleshooting an internet edge, the governing mechanism is: Compatible TCP-level BGP authentication methods can verify the configured neighbor relationship. It explains the reported symptom: An enterprise wants to protect a BGP session from a spoofed adjacent TCP peer. The intended response is: Enable matching supported BGP authentication keys on both sides and test staged replacement. Verification: The authorized peer establishes while a test using incorrect credentials is refused.

Incorrect Answers

A:

Hidden and inactive BGP paths can result from next-hop resolution, policy rejection and competing path selection. This alternative mechanism does not match the current fault.

B:

IBGP requires compatible local and remote AS settings, TCP reachability and correct neighbor addresses. Fixing that different mechanism would not address the current root cause: compatible TCP-level BGP authentication methods can verify the configured neighbor relationship.

D:

A BGP prefix-limit control detects or constrains excessive received NLRI from a peer. Its verification is distinct from the reported condition: An enterprise wants to protect a BGP session from a spoofed adjacent TCP peer. The diagnosis must distinguish a healthy BGP session from eligible received routes.

Question 604

At a university separating multiple OSPF areas, a Junos specialist investigates this scenario: An OSPF stub area receives or expects external LSA behavior incompatible with its intended design. The routing change must preserve control-plane consistency across areas. Which response best restores the intended behavior?

  1. Correct the relevant link MTU on both endpoints and restart adjacency safely if necessary.
  2. Configure the intended OSPFv3 area and IPv6-enabled link interfaces on both peers.
  3. Assign the connecting interfaces to the same intended OSPF area and validate the area boundary design.
  4. Configure a compatible stub-area type throughout the area and validate ABR default behavior.

Explanation

Correct Answer

D:

For a university separating multiple OSPF areas, the direct corrective action is: Configure a compatible stub-area type throughout the area and validate ABR default behavior. This addresses the mechanism: A conventional stub area limits external LSAs and uses a suitable default route for outside reachability. Confirm by checking: Area routers learn a usable default route without inappropriate external LSAs. During rollout, do not make an ASBR-dependent area stub without checking redistribution requirements.

Incorrect Answers

A:

Database-description exchange can fail when peers disagree on the IP MTU for a common OSPF link. The appropriate correction for the reported case is: Configure a compatible stub-area type throughout the area and validate ABR default behavior.

B:

OSPFv3 is a distinct link-state protocol requiring correct interface and area enablement for IPv6 environments. Fixing that different mechanism would not address the current root cause: a conventional stub area limits external LSAs and uses a suitable default route for outside reachability.

C:

OSPF neighbors on a common link must agree on the area identifier used in Hello processing. Its verification is distinct from the reported condition: An OSPF stub area receives or expects external LSA behavior incompatible with its intended design. The routing change must preserve control-plane consistency across areas.

Question 605

At a data-center access fabric using tagged trunks, a Junos specialist investigates this scenario: A redundant Layer 2 ring creates a broadcast storm when multiple paths forward simultaneously. The proposed behavior must be validated on actual switching ports. What would demonstrate a successful correction under test?

  1. A loop-free topology has one blocked alternate path that activates after a controlled failure.
  2. show ethernet-switching interfaces displays the assigned VLAN and test hosts reach only its subnet.
  3. show ethernet-switching table contains the expected MAC-to-port entry and forwarding becomes selective.
  4. show spanning-tree bridge identifies the intended root for each MST instance.

Explanation

Correct Answer

A:

For a data-center access fabric using tagged trunks, the decisive evidence is: A loop-free topology has one blocked alternate path that activates after a controlled failure. This validates the action: Enable a consistent MSTP topology and verify the expected alternate-port state. Because: Spanning tree prevents bridging loops by keeping appropriate redundant ports in nondesignated states. An unrelated successful test would not prove this specific issue is resolved.

Incorrect Answers

B:

An untagged Ethernet access port places endpoint traffic into its configured access VLAN. The appropriate correction for the reported case is: Enable a consistent MSTP topology and verify the expected alternate-port state.

C:

Layer 2 switches learn source MAC addresses on ingress ports and forward known unicast using their MAC tables. Fixing that different mechanism would not address the current root cause: spanning tree prevents bridging loops by keeping appropriate redundant ports in nondesignated states.

D:

Spanning-tree root selection uses bridge identifiers and configured priorities within the relevant instance. Its verification is distinct from the reported condition: A redundant Layer 2 ring creates a broadcast storm when multiple paths forward simultaneously. The proposed behavior must be validated on actual switching ports.

Question 606

At a healthcare organization connecting redundant facilities, a Junos specialist investigates this scenario: Branch OSPF peers need one controlled default exit but the upstream router floods many unnecessary external routes. The correction must not expose administrative network prefixes. Which underlying distinction should guide troubleshooting?

  1. Junos OSPF normally requires explicit export policy to redistribute eligible non-OSPF routes as external reachability.
  2. A scoped OSPF default-route export can advertise 0.0.0.0/0 when the default is valid.
  3. A passive OSPF interface can advertise attached reachability while suppressing neighbor-discovery Hellos.
  4. Junos requires a suitable route export policy to originate eligible non-OSPFv3 routes.

Explanation

Correct Answer

B:

For a healthcare organization connecting redundant facilities, the governing mechanism is: A scoped OSPF default-route export can advertise 0.0.0.0/0 when the default is valid. It explains the reported symptom: Branch OSPF peers need one controlled default exit but the upstream router floods many unnecessary external routes. The intended response is: Export only the authorized default route and confirm its next-hop and forwarding path. Verification: Branch routers receive a default route and reach the approved upstream network.

Incorrect Answers

A:

Junos OSPF normally requires explicit export policy to redistribute eligible non-OSPF routes as external reachability. This alternative mechanism does not match the current fault.

C:

A passive OSPF interface can advertise attached reachability while suppressing neighbor-discovery Hellos. Fixing that different mechanism would not address the current root cause: a scoped OSPF default-route export can advertise 0.0.0.0/0 when the default is valid.

D:

Junos requires a suitable route export policy to originate eligible non-OSPFv3 routes. Its verification is distinct from the reported condition: Branch OSPF peers need one controlled default exit but the upstream router floods many unnecessary external routes. The correction must not expose administrative network prefixes.

Question 607

At a campus network built with Juniper EX switches, a Junos specialist investigates this scenario: A campus needs certain incoming traffic to enter a VLAN based on packet attributes rather than only the fixed physical port. The intended segmentation and loop prevention must remain intact. Which configuration adjustment should be made first to address this issue?

  1. Set the intended VLAN membership on the access logical interface and verify the port mode.
  2. Set supported bridge priorities so designated distribution switches become root and backup root.
  3. Configure a supported Layer 2 firewall filter with the intended VLAN assignment action.
  4. Enable the supported BPDU protection behavior on designated host-facing ports.

Explanation

Correct Answer

C:

For a campus network built with Juniper EX switches, the direct corrective action is: Configure a supported Layer 2 firewall filter with the intended VLAN assignment action. This addresses the mechanism: Filter-based VLANs can classify ingress frames and assign eligible traffic to a selected VLAN. Confirm by checking: Matching test traffic enters the designated VLAN while nonmatching traffic follows default handling. During rollout, validate filter match order and feature support to avoid broad unintended reassignment.

Incorrect Answers

A:

An untagged Ethernet access port places endpoint traffic into its configured access VLAN. The appropriate correction for the reported case is: Configure a supported Layer 2 firewall filter with the intended VLAN assignment action.

B:

Spanning-tree root selection uses bridge identifiers and configured priorities within the relevant instance. Fixing that different mechanism would not address the current root cause: filter-based VLANs can classify ingress frames and assign eligible traffic to a selected VLAN.

D:

BPDU protection can prevent an edge interface from accepting unauthorized bridge control messages. Its verification is distinct from the reported condition: A campus needs certain incoming traffic to enter a VLAN based on packet attributes rather than only the fixed physical port. The intended segmentation and loop prevention must remain intact.

Question 608

At a large enterprise updating redundant switch links, a Junos specialist investigates this scenario: A malfunctioning device saturates one VLAN with broadcasts and causes widespread host loss. The change must retain both link resilience and correct VLAN isolation. Which underlying distinction should guide troubleshooting?

  1. Layer 2 protocol tunneling can transport specified customer control frames across a separate provider bridging domain.
  2. Private VLAN promiscuous ports can communicate with applicable secondary VLAN ports, providing a shared exit.
  3. MSTP region boundaries interact with neighboring spanning-tree variants through common spanning-tree behavior.
  4. Layer 2 storm control limits specified excessive broadcast or multicast traffic on a port.

Explanation

Correct Answer

D:

For a large enterprise updating redundant switch links, the governing mechanism is: Layer 2 storm control limits specified excessive broadcast or multicast traffic on a port. It explains the reported symptom: A malfunctioning device saturates one VLAN with broadcasts and causes widespread host loss. The intended response is: Apply suitable storm-control thresholds to the affected edge ports. Verification: A controlled burst is limited while ordinary ARP and discovery traffic remains functional.

Incorrect Answers

A:

Layer 2 protocol tunneling can transport specified customer control frames across a separate provider bridging domain. This alternative mechanism does not match the current fault.

B:

Private VLAN promiscuous ports can communicate with applicable secondary VLAN ports, providing a shared exit. Fixing that different mechanism would not address the current root cause: layer 2 storm control limits specified excessive broadcast or multicast traffic on a port.

C:

MSTP region boundaries interact with neighboring spanning-tree variants through common spanning-tree behavior. Its verification is distinct from the reported condition: A malfunctioning device saturates one VLAN with broadcasts and causes widespread host loss. The change must retain both link resilience and correct VLAN isolation.

Question 609

At an enterprise telemetry network with multicast subscribers, a Junos specialist investigates this scenario: Traffic continues on a downstream path after the final interested receiver leaves the group. The team should test joins and forwarding separately. When would the described mechanism be appropriate?

  1. Use PIM Prune signaling to remove unnecessary multicast distribution branches.
  2. Use IGMP snooping to constrain Layer 2 multicast distribution to interested ports.
  3. Use PIM designated-router selection to coordinate multicast functions on shared links.
  4. Use multicast route tables to troubleshoot one-way group forwarding failures.

Explanation

Correct Answer

A:

For an enterprise telemetry network with multicast subscribers, this mechanism fits the requirement: Use PIM Prune signaling to remove unnecessary multicast distribution branches. The design is appropriate because: PIM Join and Prune signaling maintains or removes forwarding-tree state as downstream interest changes. In this scenario, the observed issue is: Traffic continues on a downstream path after the final interested receiver leaves the group. The corresponding implementation is: Inspect and correct downstream receiver removal and upstream PIM prune processing.

Incorrect Answers

B:

IGMP snooping lets a Layer 2 switch learn interested receiver ports and limit multicast flooding within a VLAN. The appropriate correction for the reported case is: Inspect and correct downstream receiver removal and upstream PIM prune processing.

C:

PIM designated-router election selects the local router responsible for certain first-hop PIM functions. Fixing that different mechanism would not address the current root cause: PIM Join and Prune signaling maintains or removes forwarding-tree state as downstream interest changes.

D:

Multicast forwarding depends on per-group and per-source route state in addition to host membership. Its verification is distinct from the reported condition: Traffic continues on a downstream path after the final interested receiver leaves the group. The team should test joins and forwarding separately. When would the described mechanism be appropriate.

Question 610

At an enterprise telemetry network with multicast subscribers, a Junos specialist investigates this scenario: The operations team sees (S,G) entries and assumes they mean every source may send to a joined group. The team should test joins and forwarding separately. What protocol behavior accounts for this failure?

  1. IPv4 multicast traffic uses group addresses from 224.0.0.0 through 239.255.255.255 rather than ordinary unicast host destinations.
  2. (S,G) multicast state identifies one particular source S and destination group G.
  3. Multicast group and routing policies can limit which group ranges and sources cross specified boundaries.
  4. Shared-tree (*,G) state expresses interest in traffic to group G from potentially multiple sources.

Explanation

Correct Answer

B:

For an enterprise telemetry network with multicast subscribers, the governing mechanism is: (S,G) multicast state identifies one particular source S and destination group G. It explains the reported symptom: The operations team sees (S,G) entries and assumes they mean every source may send to a joined group. The intended response is: Inspect the source and group state to diagnose the correct sender-specific distribution tree. Verification: show multicast route or PIM state contains the planned source-group combination.

Incorrect Answers

A:

IPv4 multicast traffic uses group addresses from 224.0.0.0 through 239.255.255.255 rather than ordinary unicast host destinations. This alternative mechanism does not match the current fault.

C:

Multicast group and routing policies can limit which group ranges and sources cross specified boundaries. Fixing that different mechanism would not address the current root cause: (S,G) multicast state identifies one particular source S and destination group G.

D:

Shared-tree (*,G) state expresses interest in traffic to group G from potentially multiple sources. Its verification is distinct from the reported condition: The operations team sees (S,G) entries and assumes they mean every source may send to a joined group. The team should test joins and forwarding separately.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests