mcAfee Secure Website
exam =5
exam =6

Exam Code: JN0-650

Exam Name: Enterprise Routing and Switching, Professional (JNCIP-ENT)

Certification Provider: Juniper

Corresponding Certification: JNCIP-ENT

Juniper JN0-650 Questions & Answers

Reliable & Actual Study Materials for JN0-650 Exam Success

107 Questions & Answers with Testing Engine

"JN0-650: Enterprise Routing and Switching, Professional (JNCIP-ENT)" Testing Engine covers all the knowledge points of the real Juniper JN0-650 exam.

The latest actual JN0-650 Questions & Answers from Pass4sure. Everything you need to prepare and get best score at JN0-650 exam easily and quickly.

exam =7
Guarantee

Satisfaction Guaranteed

Pass4sure has a remarkable Juniper Candidate Success record. We're confident of our products and provide no hassle product exchange. That's how confident we are!

99.3% Pass Rate
Was: $137.49
Now: $124.99

Juniper JN0-650 Practice Test 78

Question 770

At a managed network team troubleshooting an internet edge, a Junos specialist investigates this scenario: An iBGP session over loopbacks fails because the outgoing TCP connection uses a physical-interface source address. The diagnosis must distinguish a healthy BGP session from eligible received routes. What is the most likely design-related cause?

  1. Route reflector cluster identifiers participate in loop detection on reflected BGP paths.
  2. Both ends of a loopback-based BGP session must reach and recognize the configured local addresses.
  3. AS-path prepending lengthens a path in selected outbound advertisements and may influence upstream BGP selection.
  4. BGP MED can signal a preferred ingress point to a neighboring AS subject to the neighbor's selection policy.

Explanation

Correct Answer

B:

For a managed network team troubleshooting an internet edge, the governing mechanism is: Both ends of a loopback-based BGP session must reach and recognize the configured local addresses. It explains the reported symptom: An iBGP session over loopbacks fails because the outgoing TCP connection uses a physical-interface source address. The intended response is: Set the BGP local-address to the intended routable loopback and verify remote peer configuration. Verification: show BGP neighbor reports the expected local source and established peer endpoint.

Incorrect Answers

A:

Route reflector cluster identifiers participate in loop detection on reflected BGP paths. This alternative mechanism does not match the current fault.

C:

AS-path prepending lengthens a path in selected outbound advertisements and may influence upstream BGP selection. Fixing that different mechanism would not address the current root cause: both ends of a loopback-based BGP session must reach and recognize the configured local addresses.

D:

BGP MED can signal a preferred ingress point to a neighboring AS subject to the neighbor's selection policy. Its verification is distinct from the reported condition: An iBGP session over loopbacks fails because the outgoing TCP connection uses a physical-interface source address. The diagnosis must distinguish a healthy BGP session from eligible received routes.

Question 771

At a healthcare organization connecting redundant facilities, a Junos specialist investigates this scenario: A team expects an IPv6 OSPFv3 next hop to appear only as a global unicast address. The correction must not expose administrative network prefixes. What risk must the implementation avoid?

  1. Verify IPv6 link-local interface reachability and security filters before assuming IPv4 OSPF proves readiness.
  2. Avoid enabling ECMP across paths with incompatible MTU or traffic-security policies.
  3. Do not remove required link-local communication while tightening IPv6 filters.
  4. Treat a virtual link as a controlled exception and plan a physical backbone repair.

Explanation

Correct Answer

C:

For a healthcare organization connecting redundant facilities, the relevant safeguard is: Do not remove required link-local communication while tightening IPv6 filters. It matters while implementing: Validate the IPv6 link-local adjacency and correct outgoing logical interface for the route. The fault involves: OSPFv3 neighbor exchanges and next-hop forwarding commonly use IPv6 link-local addresses on the adjoining link. The required acceptance result remains: An IPv6 destination installs with an expected link-local next hop and forwards successfully.

Incorrect Answers

A:

OSPFv3 is a distinct link-state protocol requiring correct interface and area enablement for IPv6 environments. The appropriate correction for the reported case is: Do not remove required link-local communication while tightening IPv6 filters.

B:

OSPF can compute equal-cost paths; forwarding utilization depends on installed next hops and platform ECMP behavior. Fixing that different mechanism would not address the current root cause: OSPFv3 neighbor exchanges and next-hop forwarding commonly use IPv6 link-local addresses on the adjoining link.

D:

A supported OSPF virtual link can logically extend the backbone through a nonstub transit area between eligible ABRs. Its verification is distinct from the reported condition: A team expects an IPv6 OSPFv3 next hop to appear only as a global unicast address. The correction must not expose administrative network prefixes.

Question 772

At a provider Ethernet network carrying customer Layer 2 services, a Junos specialist investigates this scenario: Several tenant endpoints must reach a gateway but must not exchange Layer 2 traffic with each other. The service must preserve tags without bridging unrelated tenants. Which response best restores the intended behavior?

  1. Create the intended community membership and permitted promiscuous gateway association.
  2. Configure supported provider bridging with a distinct service tag for each tenant context.
  3. Assign distinct outer service VLAN identities to the independent customer services.
  4. Map the isolated ports to the private VLAN design and configure the approved gateway-facing port.

Explanation

Correct Answer

D:

For a provider Ethernet network carrying customer Layer 2 services, the direct corrective action is: Map the isolated ports to the private VLAN design and configure the approved gateway-facing port. This addresses the mechanism: Private VLAN isolated ports restrict communication with peer isolated ports while allowing designated promiscuous connectivity. Confirm by checking: Two isolated test devices cannot communicate directly but each can reach the authorized gateway. During rollout, verify device-model support and avoid confusing private VLANs with firewall isolation between routed VLANs.

Incorrect Answers

A:

Private VLAN community ports support intra-community traffic while preventing communication with other communities. The appropriate correction for the reported case is: Map the isolated ports to the private VLAN design and configure the approved gateway-facing port.

B:

IEEE 802.1ad Q-in-Q encapsulates customer-tagged frames with an outer service VLAN tag. Fixing that different mechanism would not address the current root cause: private VLAN isolated ports restrict communication with peer isolated ports while allowing designated promiscuous connectivity.

C:

A provider S-VLAN or equivalent encapsulation boundary is needed to keep identical customer C-VLAN numbers separate. Its verification is distinct from the reported condition: Several tenant endpoints must reach a gateway but must not exchange Layer 2 traffic with each other. The service must preserve tags without bridging unrelated tenants.

Question 773

At a multihomed data center using redundant Ethernet segments, a Junos specialist investigates this scenario: A dual-homed server should use both eligible attachments but its EVPN configuration uses a standby-only design. The design must avoid forwarding loops during failover. Which technical mechanism most directly explains the symptom?

  1. EVPN all-active multihoming permits multiple PEs to forward eligible known-unicast traffic with appropriate control-plane loop prevention.
  2. EVPN Ethernet Auto-Discovery route type 1 participates in multihoming reachability and mass-withdraw behavior.
  3. EVPN Ethernet Segment route type 4 supports discovery of PEs connected to the same Ethernet segment.
  4. EVPN single-active multihoming restricts the forwarding role on an Ethernet segment to a selected active PE.

Explanation

Correct Answer

A:

For a multihomed data center using redundant Ethernet segments, the governing mechanism is: EVPN all-active multihoming permits multiple PEs to forward eligible known-unicast traffic with appropriate control-plane loop prevention. It explains the reported symptom: A dual-homed server should use both eligible attachments but its EVPN configuration uses a standby-only design. The intended response is: Configure supported all-active Ethernet segment multihoming and consistent ESI state. Verification: Eligible unicast traffic uses both active attachments and survives loss of one PE.

Incorrect Answers

B:

EVPN Ethernet Auto-Discovery route type 1 participates in multihoming reachability and mass-withdraw behavior. This alternative mechanism does not match the current fault.

C:

EVPN Ethernet Segment route type 4 supports discovery of PEs connected to the same Ethernet segment. Fixing that different mechanism would not address the current root cause: EVPN all-active multihoming permits multiple PEs to forward eligible known-unicast traffic with appropriate control-plane loop prevention.

D:

EVPN single-active multihoming restricts the forwarding role on an Ethernet segment to a selected active PE. Its verification is distinct from the reported condition: A dual-homed server should use both eligible attachments but its EVPN configuration uses a standby-only design. The design must avoid forwarding loops during failover.

Question 774

At a healthcare organization connecting redundant facilities, a Junos specialist investigates this scenario: A shared Ethernet OSPF segment has more adjacencies than planned and the chosen designated router is unsuitable. The correction must not expose administrative network prefixes. Which operational result would most clearly confirm the fix?

  1. show ospf neighbor reaches Full and periodic Hellos remain within the agreed dead interval.
  2. show ospf neighbor shows the intended DR and BDR roles and stable adjacency states.
  3. The neighbor leaves ExStart and reaches Full with synchronized link-state databases.
  4. show route detail indicates the active entry and its protocol preference for the prefix.

Explanation

Correct Answer

B:

For a healthcare organization connecting redundant facilities, the decisive evidence is: show ospf neighbor shows the intended DR and BDR roles and stable adjacency states. This validates the action: Review interface priority and network type so appropriate eligible routers become DR and BDR. Because: On broadcast multiaccess networks OSPF elects a designated router and backup designated router to manage adjacencies. An unrelated successful test would not prove this specific issue is resolved.

Incorrect Answers

A:

Neighbor compatibility depends on matching Hello and dead intervals for the participating link. The appropriate correction for the reported case is: Review interface priority and network type so appropriate eligible routers become DR and BDR.

C:

Database-description exchange can fail when peers disagree on the IP MTU for a common OSPF link. Fixing that different mechanism would not address the current root cause: on broadcast multiaccess networks OSPF elects a designated router and backup designated router to manage adjacencies.

D:

Junos first chooses active routing-table entries using protocol route preference before forwarding installation. Its verification is distinct from the reported condition: A shared Ethernet OSPF segment has more adjacencies than planned and the chosen designated router is unsuitable. The correction must not expose administrative network prefixes.

Question 775

At a campus distributing IP video to several buildings, a Junos specialist investigates this scenario: An ASM receiver joins G but routers disagree about the RP responsible for the group. The group traffic must reach interested receivers without flooding other locations. What is the most likely design-related cause?

  1. PIM Join and Prune signaling maintains or removes forwarding-tree state as downstream interest changes.
  2. PIM routers discover routing neighbors on participating interfaces through PIM Hello exchanges.
  3. PIM-SM shared-tree construction depends on consistent mappings of multicast groups to suitable RPs.
  4. IGMPv3 membership records can identify source filters that enable explicit SSM interest.

Explanation

Correct Answer

C:

For a campus distributing IP video to several buildings, the governing mechanism is: PIM-SM shared-tree construction depends on consistent mappings of multicast groups to suitable RPs. It explains the reported symptom: An ASM receiver joins G but routers disagree about the RP responsible for the group. The intended response is: Configure or correct the intended RP mapping for the affected group range throughout the domain. Verification: show pim rps reports the planned RP and receivers join the corresponding tree.

Incorrect Answers

A:

PIM Join and Prune signaling maintains or removes forwarding-tree state as downstream interest changes. This alternative mechanism does not match the current fault.

B:

PIM routers discover routing neighbors on participating interfaces through PIM Hello exchanges. Fixing that different mechanism would not address the current root cause: PIM-SM shared-tree construction depends on consistent mappings of multicast groups to suitable RPs.

D:

IGMPv3 membership records can identify source filters that enable explicit SSM interest. Its verification is distinct from the reported condition: An ASM receiver joins G but routers disagree about the RP responsible for the group. The group traffic must reach interested receivers without flooding other locations.

Question 776

At a multihomed data center using redundant Ethernet segments, a Junos specialist investigates this scenario: Multiple PEs attach to one Ethernet segment but cannot discover consistent peers for multihoming decisions. The design must avoid forwarding loops during failover. What requirement most specifically calls for this approach?

  1. Use EVPN type-1 routes for Ethernet segment reachability and efficient multihoming withdrawal.
  2. Use EVPN type-2 routes to announce host MAC and optional IP reachability.
  3. Use all-active EVPN multihoming for simultaneous eligible forwarding across redundant PEs.
  4. Use EVPN type-4 routes for Ethernet segment discovery among multihomed peers.

Explanation

Correct Answer

D:

For a multihomed data center using redundant Ethernet segments, this mechanism fits the requirement: Use EVPN type-4 routes for Ethernet segment discovery among multihomed peers. The design is appropriate because: EVPN Ethernet Segment route type 4 supports discovery of PEs connected to the same Ethernet segment. In this scenario, the observed issue is: Multiple PEs attach to one Ethernet segment but cannot discover consistent peers for multihoming decisions. The corresponding implementation is: Verify compatible Ethernet segment identifiers and advertisement of type-4 segment routes.

Incorrect Answers

A:

EVPN Ethernet Auto-Discovery route type 1 participates in multihoming reachability and mass-withdraw behavior. The appropriate correction for the reported case is: Verify compatible Ethernet segment identifiers and advertisement of type-4 segment routes.

B:

EVPN route type 2 advertises MAC reachability and can include associated IP information for hosts. Fixing that different mechanism would not address the current root cause: EVPN Ethernet Segment route type 4 supports discovery of PEs connected to the same Ethernet segment.

C:

EVPN all-active multihoming permits multiple PEs to forward eligible known-unicast traffic with appropriate control-plane loop prevention. Its verification is distinct from the reported condition: Multiple PEs attach to one Ethernet segment but cannot discover consistent peers for multihoming decisions. The design must avoid forwarding loops during failover.

Question 777

At a service provider offering isolated VXLAN services, a Junos specialist investigates this scenario: A VXLAN broadcast frame never reaches remote VTEPs even though known unicast MAC lookups work. The engineer must verify both BGP EVPN signaling and underlay reachability. Which response best restores the intended behavior?

  1. Ensure eligible IMET route advertisements and the configured VXLAN replication mechanism are consistent.
  2. Verify the local MAC/IP advertisement and its acceptance through the correct EVPN instance.
  3. Advertise the intended IP prefixes through an eligible EVPN routing instance and import targets.
  4. Configure a consistent nonconflicting ESI on the intended dual-homed attachment.

Explanation

Correct Answer

A:

For a service provider offering isolated VXLAN services, the direct corrective action is: Ensure eligible IMET route advertisements and the configured VXLAN replication mechanism are consistent. This addresses the mechanism: EVPN route type 3 carries inclusive multicast Ethernet tag information used to establish BUM replication membership. Confirm by checking: Remote VTEPs have the expected BUM distribution list and ARP broadcast traffic arrives. During rollout, constrain flooding domain and avoid replicating unknown unicast to unauthorized VTEPs.

Incorrect Answers

B:

EVPN route type 2 advertises MAC reachability and can include associated IP information for hosts. The appropriate correction for the reported case is: Ensure eligible IMET route advertisements and the configured VXLAN replication mechanism are consistent.

C:

EVPN route type 5 conveys IP prefix reachability and can support routed overlay designs. Fixing that different mechanism would not address the current root cause: EVPN route type 3 carries inclusive multicast Ethernet tag information used to establish BUM replication membership.

D:

A common Ethernet Segment Identifier identifies the shared multihomed Ethernet segment for EVPN coordination. Its verification is distinct from the reported condition: A VXLAN broadcast frame never reaches remote VTEPs even though known unicast MAC lookups work. The engineer must verify both BGP EVPN signaling and underlay reachability.

Question 778

At a regional provider operating Junos-based branch routers, a Junos specialist investigates this scenario: OSPF adjacency troubleshooting reveals two different devices using the same router identifier. The team must validate neighbor state rather than assume basic IP reachability proves routing. What verification result should the engineer expect?

  1. show route detail indicates the active entry and its protocol preference for the prefix.
  2. Each OSPF peer reports a distinct expected router ID and adjacency state becomes stable.
  3. Area routers learn a usable default route without inappropriate external LSAs.
  4. OSPF topology and route-change counters settle after fault correction.

Explanation

Correct Answer

B:

For a regional provider operating Junos-based branch routers, the decisive evidence is: Each OSPF peer reports a distinct expected router ID and adjacency state becomes stable. This validates the action: Configure distinct stable router IDs and restart or refresh affected protocol processes as supported. Because: The OSPF router ID uniquely identifies an originator of link-state information within the routing domain. An unrelated successful test would not prove this specific issue is resolved.

Incorrect Answers

A:

Junos first chooses active routing-table entries using protocol route preference before forwarding installation. The appropriate correction for the reported case is: Configure distinct stable router IDs and restart or refresh affected protocol processes as supported.

C:

A conventional stub area limits external LSAs and uses a suitable default route for outside reachability. Fixing that different mechanism would not address the current root cause: the OSPF router ID uniquely identifies an originator of link-state information within the routing domain.

D:

Link-state SPF recalculation is triggered by topology changes and must converge over a coherent LSDB. Its verification is distinct from the reported condition: OSPF adjacency troubleshooting reveals two different devices using the same router identifier. The team must validate neighbor state rather than assume basic IP reachability proves routing.

Question 779

At a service provider offering isolated VXLAN services, a Junos specialist investigates this scenario: Two VTEPs reach each other but a tenant VLAN crosses into the wrong remote Ethernet segment. The engineer must verify both BGP EVPN signaling and underlay reachability. Which operational change most directly resolves the observed failure?

  1. Repair underlay routes, relevant UDP encapsulation permission and VTEP reachability.
  2. Configure a consistent nonconflicting ESI on the intended dual-homed attachment.
  3. Align the intended VLAN-to-VNI mapping across participating leaf switches.
  4. Provide sufficient underlay MTU for the intended inner payload or constrain end-host MTU safely.

Explanation

Correct Answer

C:

For a service provider offering isolated VXLAN services, the direct corrective action is: Align the intended VLAN-to-VNI mapping across participating leaf switches. This addresses the mechanism: VXLAN uses a 24-bit VNI to identify a logical overlay segment associated with local bridging context. Confirm by checking: A test host in one VLAN exchanges frames only with its matching remote VNI segment. During rollout, avoid reusing one VNI for unrelated tenant isolation boundaries.

Incorrect Answers

A:

VXLAN tunnels require IP reachability between VTEP addresses and adequate underlay transport capacity. The appropriate correction for the reported case is: Align the intended VLAN-to-VNI mapping across participating leaf switches.

B:

A common Ethernet Segment Identifier identifies the shared multihomed Ethernet segment for EVPN coordination. Fixing that different mechanism would not address the current root cause: VXLAN uses a 24-bit VNI to identify a logical overlay segment associated with local bridging context.

D:

VXLAN adds outer Ethernet, IP, UDP and VXLAN encapsulation overhead to tenant frames. Its verification is distinct from the reported condition: Two VTEPs reach each other but a tenant VLAN crosses into the wrong remote Ethernet segment. The engineer must verify both BGP EVPN signaling and underlay reachability.

Question 780

At a managed network team troubleshooting an internet edge, a Junos specialist investigates this scenario: An enterprise wants to make one inbound route advertisement less attractive without withdrawing reachability. The diagnosis must distinguish a healthy BGP session from eligible received routes. Which response best restores the intended behavior?

  1. Place specific prefix rejection before a broader permitted match in the relevant policy.
  2. Configure supported eBGP multihop behavior and reliable local-address selection for the approved peer.
  3. Inspect AS-path attributes and modify permitted policy only if a different transit choice is justified.
  4. Apply targeted AS-path prepend in an authorized export policy for the backup link.

Explanation

Correct Answer

D:

For a managed network team troubleshooting an internet edge, the direct corrective action is: Apply targeted AS-path prepend in an authorized export policy for the backup link. This addresses the mechanism: AS-path prepending lengthens a path in selected outbound advertisements and may influence upstream BGP selection. Confirm by checking: The upstream receives the appended path and a controlled test prefers the primary ingress. During rollout, do not prepend sensitive internal ASNs indiscriminately or claim guaranteed internet-wide steering.

Incorrect Answers

A:

Junos policy terms are evaluated in configured order and a terminating action can end processing early. The appropriate correction for the reported case is: Apply targeted AS-path prepend in an authorized export policy for the backup link.

B:

A nonadjacent eBGP neighbor may require a compatible multihop TTL and suitable route to the remote endpoint. Fixing that different mechanism would not address the current root cause: AS-path prepending lengthens a path in selected outbound advertisements and may influence upstream BGP selection.

C:

In Junos BGP best-path selection an eligible shorter AS path is generally preferred after higher-priority criteria tie. Its verification is distinct from the reported condition: An enterprise wants to make one inbound route advertisement less attractive without withdrawing reachability. The diagnosis must distinguish a healthy BGP session from eligible received routes.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests