mcAfee Secure Website
exam =5
exam =6

Exam Code: JN0-650

Exam Name: Enterprise Routing and Switching, Professional (JNCIP-ENT)

Certification Provider: Juniper

Corresponding Certification: JNCIP-ENT

Juniper JN0-650 Questions & Answers

Reliable & Actual Study Materials for JN0-650 Exam Success

107 Questions & Answers with Testing Engine

"JN0-650: Enterprise Routing and Switching, Professional (JNCIP-ENT)" Testing Engine covers all the knowledge points of the real Juniper JN0-650 exam.

The latest actual JN0-650 Questions & Answers from Pass4sure. Everything you need to prepare and get best score at JN0-650 exam easily and quickly.

exam =7
Guarantee

Satisfaction Guaranteed

Pass4sure has a remarkable Juniper Candidate Success record. We're confident of our products and provide no hassle product exchange. That's how confident we are!

99.3% Pass Rate
Was: $137.49
Now: $124.99

Juniper JN0-650 Practice Test 54

Question 530

At a national enterprise designing OSPF between offices, a Junos specialist investigates this scenario: Two available OSPF WAN paths use the less desirable circuit even though both adjacencies are healthy. The internal forwarding path must remain stable when one uplink fails. What important rollout safeguard is most relevant here?

  1. Do not activate the routing protocol on an untrusted or management-facing interface accidentally.
  2. Check bidirectional traffic and backup capacity before adjusting link metrics.
  3. Do not change the backbone area relationship without validating ABR connectivity.
  4. Avoid applying IPv4 OSPF LSA type assumptions to OSPFv3 packet formats.

Explanation

Correct Answer

B:

For a national enterprise designing OSPF between offices, the relevant safeguard is: Check bidirectional traffic and backup capacity before adjusting link metrics. It matters while implementing: Set appropriate interface metrics that reflect the desired route costs across the topology. The fault involves: OSPF shortest-path selection is driven by cumulative link metrics rather than a human label for preferred circuits. The required acceptance result remains: The intended path has lower total cost and appears as the active route for a test prefix.

Incorrect Answers

A:

OSPF neighbor discovery requires the relevant logical interface to participate in the correct routing instance and area. The appropriate correction for the reported case is: Check bidirectional traffic and backup capacity before adjusting link metrics.

C:

OSPF neighbors on a common link must agree on the area identifier used in Hello processing. Fixing that different mechanism would not address the current root cause: OSPF shortest-path selection is driven by cumulative link metrics rather than a human label for preferred circuits.

D:

OSPFv3 interarea-prefix LSAs convey reachable IPv6 prefixes across area boundaries. Its verification is distinct from the reported condition: Two available OSPF WAN paths use the less desirable circuit even though both adjacencies are healthy. The internal forwarding path must remain stable when one uplink fails.

Question 531

At a regional provider operating Junos-based branch routers, a Junos specialist investigates this scenario: An OSPF-enabled router has a reachable interface but has no adjacency on that subnet. The team must validate neighbor state rather than assume basic IP reachability proves routing. What protocol behavior accounts for this failure?

  1. Link-state SPF recalculation is triggered by topology changes and must converge over a coherent LSDB.
  2. OSPF interface network type influences neighbor formation and whether DR and BDR election is used.
  3. OSPF neighbor discovery requires the relevant logical interface to participate in the correct routing instance and area.
  4. OSPF neighbors on a common link must agree on the area identifier used in Hello processing.

Explanation

Correct Answer

C:

For a regional provider operating Junos-based branch routers, the governing mechanism is: OSPF neighbor discovery requires the relevant logical interface to participate in the correct routing instance and area. It explains the reported symptom: An OSPF-enabled router has a reachable interface but has no adjacency on that subnet. The intended response is: Enable OSPF on the intended logical interface under the appropriate area and confirm its interface parameters. Verification: The peer appears in show ospf neighbor and the local interface appears in show ospf interface.

Incorrect Answers

A:

Link-state SPF recalculation is triggered by topology changes and must converge over a coherent LSDB. This alternative mechanism does not match the current fault.

B:

OSPF interface network type influences neighbor formation and whether DR and BDR election is used. Fixing that different mechanism would not address the current root cause: OSPF neighbor discovery requires the relevant logical interface to participate in the correct routing instance and area.

D:

OSPF neighbors on a common link must agree on the area identifier used in Hello processing. Its verification is distinct from the reported condition: An OSPF-enabled router has a reachable interface but has no adjacency on that subnet. The team must validate neighbor state rather than assume basic IP reachability proves routing.

Question 532

At a dual-homed business network peering with two upstream providers, a Junos specialist investigates this scenario: Two candidate BGP paths are comparable in earlier attributes but one was learned via eBGP and the other iBGP. The routing policy must retain intended primary and backup paths. What would demonstrate a successful correction under test?

  1. Internal routers resolve the advertised next hop through the enterprise IGP and can forward to the prefix.
  2. The authorized peer establishes while a test using incorrect credentials is refused.
  3. show bgp neighbor reports Established with the expected external peer AS.
  4. The active BGP path reflects eBGP preference only when earlier criteria do not decide first.

Explanation

Correct Answer

D:

For a dual-homed business network peering with two upstream providers, the decisive evidence is: The active BGP path reflects eBGP preference only when earlier criteria do not decide first. This validates the action: Review peer type and the complete path decision chain before adjusting selection policy. Because: Junos BGP best-path logic generally prefers the external route when preceding comparisons tie. An unrelated successful test would not prove this specific issue is resolved.

Incorrect Answers

A:

IBGP propagation may retain the original eBGP next-hop attribute unless policy or configuration changes it. The appropriate correction for the reported case is: Review peer type and the complete path decision chain before adjusting selection policy.

B:

Compatible TCP-level BGP authentication methods can verify the configured neighbor relationship. Fixing that different mechanism would not address the current root cause: junos BGP best-path logic generally prefers the external route when preceding comparisons tie.

C:

BGP OPEN messages carry AS information and external peers must agree on their intended local and remote AS relationship. Its verification is distinct from the reported condition: Two candidate BGP paths are comparable in earlier attributes but one was learned via eBGP and the other iBGP. The routing policy must retain intended primary and backup paths.

Question 533

At a regional provider operating Junos-based branch routers, a Junos specialist investigates this scenario: A branch area needs to redistribute local prefixes but must still avoid full external LSA flooding. The team must validate neighbor state rather than assume basic IP reachability proves routing. Which operational change most directly resolves the observed failure?

  1. Configure a consistent NSSA area and permitted redistribution at the branch ASBR.
  2. Check ABR area topology and permitted interarea prefix advertisement for the missing network.
  3. Configure supported OSPF passive behavior on the host-facing interface.
  4. Configure a compatible stub-area type throughout the area and validate ABR default behavior.

Explanation

Correct Answer

A:

For a regional provider operating Junos-based branch routers, the direct corrective action is: Configure a consistent NSSA area and permitted redistribution at the branch ASBR. This addresses the mechanism: A not-so-stubby area allows local external routes using type-7 LSAs and an ABR can translate them toward other areas. Confirm by checking: The local type-7 advertisement appears and translated external reachability is available outside the NSSA. During rollout, verify translation and filtering so unwanted branch routes do not escape the area.

Incorrect Answers

B:

OSPFv3 interarea-prefix LSAs convey reachable IPv6 prefixes across area boundaries. The appropriate correction for the reported case is: Configure a consistent NSSA area and permitted redistribution at the branch ASBR.

C:

A passive OSPF interface can advertise attached reachability while suppressing neighbor-discovery Hellos. Fixing that different mechanism would not address the current root cause: a not-so-stubby area allows local external routes using type-7 LSAs and an ABR can translate them toward other areas.

D:

A conventional stub area limits external LSAs and uses a suitable default route for outside reachability. Its verification is distinct from the reported condition: A branch area needs to redistribute local prefixes but must still avoid full external LSA flooding. The team must validate neighbor state rather than assume basic IP reachability proves routing.

Question 534

At an enterprise telemetry network with multicast subscribers, a Junos specialist investigates this scenario: Many ASM receivers depend on one RP and lose initial source discovery after that device fails. The team should test joins and forwarding separately. What would demonstrate a successful correction under test?

  1. Routers learn the expected RP mapping and group traffic builds a valid shared tree.
  2. After one RP fails, new group joins reach the surviving RP and active sources remain discoverable.
  3. The multicast forwarding state uses the intended RPF interface and packet discard counters stop increasing.
  4. An eligible receiver joins the IPv6 multicast group and receives one expected copy.

Explanation

Correct Answer

B:

For an enterprise telemetry network with multicast subscribers, the decisive evidence is: After one RP fails, new group joins reach the surviving RP and active sources remain discoverable. This validates the action: Deploy supported anycast RP members with the necessary source-state exchange mechanism. Because: Anycast RP permits multiple rendezvous points to share one RP address with routing choosing a reachable instance. An unrelated successful test would not prove this specific issue is resolved.

Incorrect Answers

A:

PIM bootstrap router mechanisms can advertise eligible RP information to routers in the multicast domain. The appropriate correction for the reported case is: Deploy supported anycast RP members with the necessary source-state exchange mechanism.

C:

Multicast reverse-path forwarding verifies that a packet arrives via a valid route back toward its source or RP. Fixing that different mechanism would not address the current root cause: anycast RP permits multiple rendezvous points to share one RP address with routing choosing a reachable instance.

D:

IPv6 multicast destinations begin in the FF00::/8 range and include scope information. Its verification is distinct from the reported condition: Many ASM receivers depend on one RP and lose initial source discovery after that device fails. The team should test joins and forwarding separately.

Question 535

At a medical facility deploying high-power conference phones, a Junos specialist investigates this scenario: A new IP phone requests a higher supported power class but is limited to a default allocation and fails to start. The phone network must retain appropriate VLAN and voice QoS treatment. Which response best restores the intended behavior?

  1. Verify total PoE capacity and allocate sufficient per-port power for the installed phones.
  2. Validate the phone passthrough configuration and Junos port VLAN membership for both traffic types.
  3. Enable appropriate PoE class handling and compatible power negotiation for the phone.
  4. Configure the intended voice VLAN and data VLAN relationship on the shared access connection.

Explanation

Correct Answer

C:

For a medical facility deploying high-power conference phones, the direct corrective action is: Enable appropriate PoE class handling and compatible power negotiation for the phone. This addresses the mechanism: PoE power classification informs the power source of the powered device's required allocation. Confirm by checking: Switch power telemetry shows the correct allocated class and the phone operates stably. During rollout, verify the negotiated class and switch feature support before overriding port power limits.

Incorrect Answers

A:

PoE availability depends on available switch power budget and each attached device's negotiated consumption. The appropriate correction for the reported case is: Enable appropriate PoE class handling and compatible power negotiation for the phone.

B:

An Ethernet phone can bridge tagged voice traffic and untagged workstation traffic with appropriate VLAN behavior. Fixing that different mechanism would not address the current root cause: poE power classification informs the power source of the powered device's required allocation.

D:

A voice VLAN permits supported tagged phone traffic to use a separate VLAN from ordinary untagged data traffic. Its verification is distinct from the reported condition: A new IP phone requests a higher supported power class but is limited to a default allocation and fails to start. The phone network must retain appropriate VLAN and voice QoS treatment.

Question 536

At a data-center access fabric using tagged trunks, a Junos specialist investigates this scenario: Customer spanning-tree BPDUs must traverse a provider Layer 2 network without controlling the provider's own spanning tree. The proposed behavior must be validated on actual switching ports. Which limitation should guide the change control?

  1. Avoid permitting all VLANs indiscriminately and confirm native VLAN assumptions.
  2. Do not assume per-instance MST details traverse an incompatible external region unchanged.
  3. Avoid very low thresholds that block legitimate discovery bursts.
  4. Constrain tunneling to approved protocols and monitor control-plane traffic rate.

Explanation

Correct Answer

D:

For a data-center access fabric using tagged trunks, the relevant safeguard is: Constrain tunneling to approved protocols and monitor control-plane traffic rate. It matters while implementing: Enable the supported L2PT mechanism for the selected customer control protocol and service VLAN. The fault involves: Layer 2 protocol tunneling can transport specified customer control frames across a separate provider bridging domain. The required acceptance result remains: Customer control frames arrive at the remote customer edge without altering provider bridge state.

Incorrect Answers

A:

An Ethernet trunk carries selected tagged VLANs and membership must include every allowed VLAN. The appropriate correction for the reported case is: Constrain tunneling to approved protocols and monitor control-plane traffic rate.

B:

MSTP region boundaries interact with neighboring spanning-tree variants through common spanning-tree behavior. Fixing that different mechanism would not address the current root cause: layer 2 protocol tunneling can transport specified customer control frames across a separate provider bridging domain.

C:

Layer 2 storm control limits specified excessive broadcast or multicast traffic on a port. Its verification is distinct from the reported condition: Customer spanning-tree BPDUs must traverse a provider Layer 2 network without controlling the provider's own spanning tree. The proposed behavior must be validated on actual switching ports.

Question 537

At a large organization using Junos route reflectors, a Junos specialist investigates this scenario: An enterprise iBGP network cannot scale because every routing speaker requires a direct adjacency with every other speaker. The change must not introduce an unwanted autonomous-system route leak. Which underlying distinction should guide troubleshooting?

  1. Ordinary iBGP split-horizon rules avoid re-advertising routes between iBGP peers; route reflectors provide controlled reflection.
  2. Route reflector cluster identifiers participate in loop detection on reflected BGP paths.
  3. BGP NLRI family selection must include inet-unicast for eligible IPv4 unicast prefixes.
  4. BGP address-family negotiation determines whether IPv6 unicast NLRI can be exchanged.

Explanation

Correct Answer

A:

For a large organization using Junos route reflectors, the governing mechanism is: Ordinary iBGP split-horizon rules avoid re-advertising routes between iBGP peers; route reflectors provide controlled reflection. It explains the reported symptom: An enterprise iBGP network cannot scale because every routing speaker requires a direct adjacency with every other speaker. The intended response is: Deploy supported route-reflector clusters and designate approved clients with appropriate topology. Verification: Reflector clients receive BGP routes from other clients through the reflector.

Incorrect Answers

B:

Route reflector cluster identifiers participate in loop detection on reflected BGP paths. This alternative mechanism does not match the current fault.

C:

BGP NLRI family selection must include inet-unicast for eligible IPv4 unicast prefixes. Fixing that different mechanism would not address the current root cause: ordinary iBGP split-horizon rules avoid re-advertising routes between iBGP peers; route reflectors provide controlled reflection.

D:

BGP address-family negotiation determines whether IPv6 unicast NLRI can be exchanged. Its verification is distinct from the reported condition: An enterprise iBGP network cannot scale because every routing speaker requires a direct adjacency with every other speaker. The change must not introduce an unwanted autonomous-system route leak.

Question 538

At a university separating multiple OSPF areas, a Junos specialist investigates this scenario: Branch OSPF peers need one controlled default exit but the upstream router floods many unnecessary external routes. The routing change must preserve control-plane consistency across areas. What is the most appropriate correction to implement?

  1. Apply a targeted interarea summarization or route-control policy at the correct OSPF hierarchy.
  2. Export only the authorized default route and confirm its next-hop and forwarding path.
  3. Create a tightly scoped policy matching the intended static prefix and apply it as an OSPF export policy.
  4. Compare show ospf database and LSAs against the intended origin and area boundaries.

Explanation

Correct Answer

B:

For a university separating multiple OSPF areas, the direct corrective action is: Export only the authorized default route and confirm its next-hop and forwarding path. This addresses the mechanism: A scoped OSPF default-route export can advertise 0.0.0.0/0 when the default is valid. Confirm by checking: Branch routers receive a default route and reach the approved upstream network. During rollout, avoid originating a default to a dead WAN without route tracking or failover planning.

Incorrect Answers

A:

OSPF interarea summary-LSA generation can be governed with supported routing policies on ABRs. The appropriate correction for the reported case is: Export only the authorized default route and confirm its next-hop and forwarding path.

C:

Junos OSPF normally requires explicit export policy to redistribute eligible non-OSPF routes as external reachability. Fixing that different mechanism would not address the current root cause: a scoped OSPF default-route export can advertise 0.0.0.0/0 when the default is valid.

D:

The link-state database and area LSA contents determine which routes the OSPF calculation can derive. Its verification is distinct from the reported condition: Branch OSPF peers need one controlled default exit but the upstream router floods many unnecessary external routes. The routing change must preserve control-plane consistency across areas.

Question 539

At a congested enterprise WAN carrying video, voice and backups, a Junos specialist investigates this scenario: Junos CoS classifiers and schedulers are configured but packets continue to use unexpected default queues. The network must keep critical application latency within policy. Which operational result would most clearly confirm the fix?

  1. Queue counters show the intended class receives its planned share during a controlled load.
  2. Packet captures on egress show the agreed DSCP values for representative classes.
  3. Interface queue statistics reflect the configured scheduler allocation under test.
  4. Voice queue delay remains within the target while lower classes still receive required service.

Explanation

Correct Answer

C:

For a congested enterprise WAN carrying video, voice and backups, the decisive evidence is: Interface queue statistics reflect the configured scheduler allocation under test. This validates the action: Attach the intended scheduler map to the correct supported egress interface. Because: A scheduler map must be associated with the appropriate interface for selected class-to-scheduler behavior. An unrelated successful test would not prove this specific issue is resolved.

Incorrect Answers

A:

Junos schedulers control bandwidth allocation among queues using configured transmission rates and priorities. The appropriate correction for the reported case is: Attach the intended scheduler map to the correct supported egress interface.

B:

Junos rewrite rules map internal forwarding class and loss-priority information to outgoing packet codepoints. Fixing that different mechanism would not address the current root cause: a scheduler map must be associated with the appropriate interface for selected class-to-scheduler behavior.

D:

A scheduler can prioritize selected latency-sensitive queues over other queues when the interface is congested. Its verification is distinct from the reported condition: Junos CoS classifiers and schedulers are configured but packets continue to use unexpected default queues. The network must keep critical application latency within policy.

Question 540

At a managed network team troubleshooting an internet edge, a Junos specialist investigates this scenario: An iBGP session over loopbacks fails because the outgoing TCP connection uses a physical-interface source address. The diagnosis must distinguish a healthy BGP session from eligible received routes. When would the described mechanism be appropriate?

  1. Use eBGP multihop for intentionally non-direct external BGP peerings.
  2. Use iBGP to distribute BGP-learned routes within one autonomous system.
  3. Use inet6-unicast BGP family to advertise and receive IPv6 network reachability.
  4. Use stable loopback addresses for resilient internal BGP sessions.

Explanation

Correct Answer

D:

For a managed network team troubleshooting an internet edge, this mechanism fits the requirement: Use stable loopback addresses for resilient internal BGP sessions. The design is appropriate because: Both ends of a loopback-based BGP session must reach and recognize the configured local addresses. In this scenario, the observed issue is: An iBGP session over loopbacks fails because the outgoing TCP connection uses a physical-interface source address. The corresponding implementation is: Set the BGP local-address to the intended routable loopback and verify remote peer configuration.

Incorrect Answers

A:

A nonadjacent eBGP neighbor may require a compatible multihop TTL and suitable route to the remote endpoint. The appropriate correction for the reported case is: Set the BGP local-address to the intended routable loopback and verify remote peer configuration.

B:

IBGP requires compatible local and remote AS settings, TCP reachability and correct neighbor addresses. Fixing that different mechanism would not address the current root cause: both ends of a loopback-based BGP session must reach and recognize the configured local addresses.

C:

BGP address-family negotiation determines whether IPv6 unicast NLRI can be exchanged. Its verification is distinct from the reported condition: An iBGP session over loopbacks fails because the outgoing TCP connection uses a physical-interface source address. The diagnosis must distinguish a healthy BGP session from eligible received routes. When would the described mechanism be appropriate.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests