mcAfee Secure Website
exam =5
exam =6

Exam Code: JN0-650

Exam Name: Enterprise Routing and Switching, Professional (JNCIP-ENT)

Certification Provider: Juniper

Corresponding Certification: JNCIP-ENT

Juniper JN0-650 Questions & Answers

Reliable & Actual Study Materials for JN0-650 Exam Success

107 Questions & Answers with Testing Engine

"JN0-650: Enterprise Routing and Switching, Professional (JNCIP-ENT)" Testing Engine covers all the knowledge points of the real Juniper JN0-650 exam.

The latest actual JN0-650 Questions & Answers from Pass4sure. Everything you need to prepare and get best score at JN0-650 exam easily and quickly.

exam =7
Guarantee

Satisfaction Guaranteed

Pass4sure has a remarkable Juniper Candidate Success record. We're confident of our products and provide no hassle product exchange. That's how confident we are!

99.3% Pass Rate
Was: $137.49
Now: $124.99

Juniper JN0-650 Practice Test 28

Question 270

At an enterprise core exchanging BGP routes over redundant WAN paths, a Junos specialist investigates this scenario: An iBGP session over loopbacks fails because the outgoing TCP connection uses a physical-interface source address. The chosen route must have a valid data-plane next hop. Which configuration adjustment should be made first to address this issue?

  1. Correct the unintended AS-path manipulation or routing leak rather than disabling loop protection.
  2. Set the BGP local-address to the intended routable loopback and verify remote peer configuration.
  3. Apply targeted AS-path prepend in an authorized export policy for the backup link.
  4. Review peer type and the complete path decision chain before adjusting selection policy.

Explanation

Correct Answer

B:

For an enterprise core exchanging BGP routes over redundant WAN paths, the direct corrective action is: Set the BGP local-address to the intended routable loopback and verify remote peer configuration. This addresses the mechanism: Both ends of a loopback-based BGP session must reach and recognize the configured local addresses. Confirm by checking: show BGP neighbor reports the expected local source and established peer endpoint. During rollout, ensure underlay IGP reachability to loopbacks before pinning the session source.

Incorrect Answers

A:

BGP AS-path loop detection normally prevents accepting routes already traversing the local autonomous system. The appropriate correction for the reported case is: Set the BGP local-address to the intended routable loopback and verify remote peer configuration.

C:

AS-path prepending lengthens a path in selected outbound advertisements and may influence upstream BGP selection. Fixing that different mechanism would not address the current root cause: both ends of a loopback-based BGP session must reach and recognize the configured local addresses.

D:

Junos BGP best-path logic generally prefers the external route when preceding comparisons tie. Its verification is distinct from the reported condition: An iBGP session over loopbacks fails because the outgoing TCP connection uses a physical-interface source address. The chosen route must have a valid data-plane next hop.

Question 271

At a dual-homed business network peering with two upstream providers, a Junos specialist investigates this scenario: A BGP router has internal routes in its RIB but should advertise only an authorized subset to an external peer. The routing policy must retain intended primary and backup paths. Which design objective is best served by this mechanism?

  1. Use BGP import policy to control external route acceptance.
  2. Use consistent cluster-ID design for redundant route reflectors in one cluster.
  3. Use BGP export policy to restrict outbound network advertisements.
  4. Use BGP route reflectors to scale internal route distribution beyond a full mesh.

Explanation

Correct Answer

C:

For a dual-homed business network peering with two upstream providers, this mechanism fits the requirement: Use BGP export policy to restrict outbound network advertisements. The design is appropriate because: BGP export policy controls which eligible active routes the speaker announces to selected neighbors. In this scenario, the observed issue is: A BGP router has internal routes in its RIB but should advertise only an authorized subset to an external peer. The corresponding implementation is: Apply a narrowly matched export policy for intended prefixes to the relevant BGP group.

Incorrect Answers

A:

A BGP import policy determines which incoming route advertisements are accepted into the routing table. The appropriate correction for the reported case is: Apply a narrowly matched export policy for intended prefixes to the relevant BGP group.

B:

Route reflector cluster identifiers participate in loop detection on reflected BGP paths. Fixing that different mechanism would not address the current root cause: BGP export policy controls which eligible active routes the speaker announces to selected neighbors.

D:

Ordinary iBGP split-horizon rules avoid re-advertising routes between iBGP peers; route reflectors provide controlled reflection. Its verification is distinct from the reported condition: A BGP router has internal routes in its RIB but should advertise only an authorized subset to an external peer. The routing policy must retain intended primary and backup paths.

Question 272

At an enterprise telemetry network with multicast subscribers, a Junos specialist investigates this scenario: A conferencing application expects an unknown multicast source but engineers require each client to specify a sender IP. The team should test joins and forwarding separately. What protocol behavior accounts for this failure?

  1. PIM sparse mode builds multicast forwarding paths in response to explicit joins rather than flooding everywhere.
  2. IGMP membership maintenance relies on periodic queries from a suitable multicast querier.
  3. PIM-SM can transition selected traffic from an RP-rooted shared tree to a source-rooted shortest-path tree.
  4. Any-source multicast allows receivers to request a group independent of a specific source, typically using a shared-tree mechanism.

Explanation

Correct Answer

D:

For an enterprise telemetry network with multicast subscribers, the governing mechanism is: Any-source multicast allows receivers to request a group independent of a specific source, typically using a shared-tree mechanism. It explains the reported symptom: A conferencing application expects an unknown multicast source but engineers require each client to specify a sender IP. The intended response is: Design a suitable ASM group with functioning IGMP membership and rendezvous-point information. Verification: A receiver can join G and obtain traffic from an approved discovered sender.

Incorrect Answers

A:

PIM sparse mode builds multicast forwarding paths in response to explicit joins rather than flooding everywhere. This alternative mechanism does not match the current fault.

B:

IGMP membership maintenance relies on periodic queries from a suitable multicast querier. Fixing that different mechanism would not address the current root cause: any-source multicast allows receivers to request a group independent of a specific source, typically using a shared-tree mechanism.

C:

PIM-SM can transition selected traffic from an RP-rooted shared tree to a source-rooted shortest-path tree. Its verification is distinct from the reported condition: A conferencing application expects an unknown multicast source but engineers require each client to specify a sender IP. The team should test joins and forwarding separately.

Question 273

At a campus switch team configuring Junos egress queues, a Junos specialist investigates this scenario: A trunk receives correctly PCP-tagged Ethernet frames but their Layer 2 priority is ignored at the receiving switch. The improvement must not starve business traffic. Which precaution should be checked before committing the change?

  1. Validate VLAN tagging and trust boundary before treating all access-port PCP markings as genuine.
  2. Do not treat packet-loss priority as a substitute for guaranteed bandwidth or physical capacity.
  3. Do not trust unverified DSCP values from arbitrary user-controlled ports.
  4. Do not increase burst allowances so far that the downstream circuit is overwhelmed.

Explanation

Correct Answer

A:

For a campus switch team configuring Junos egress queues, the relevant safeguard is: Validate VLAN tagging and trust boundary before treating all access-port PCP markings as genuine. It matters while implementing: Apply an appropriate IEEE 802.1p classifier on the trusted tagged ingress port. The fault involves: IEEE 802.1p priority values in tagged Ethernet frames can drive behavior aggregate Layer 2 CoS classification. The required acceptance result remains: A capture and queue counters show tagged priority values mapped to the expected classes.

Incorrect Answers

B:

Junos packet-loss priority provides an additional attribute for drop-profile selection under queue pressure. The appropriate correction for the reported case is: Validate VLAN tagging and trust boundary before treating all access-port PCP markings as genuine.

C:

A behavior aggregate classifier maps incoming codepoint values to local forwarding class and loss priority. Fixing that different mechanism would not address the current root cause: IEEE 802.1p priority values in tagged Ethernet frames can drive behavior aggregate Layer 2 CoS classification.

D:

Rate policers use token or burst parameters that influence which short bursts are considered conformant. Its verification is distinct from the reported condition: A trunk receives correctly PCP-tagged Ethernet frames but their Layer 2 priority is ignored at the receiving switch. The improvement must not starve business traffic.

Question 274

At an enterprise telemetry network with multicast subscribers, a Junos specialist investigates this scenario: An engineer tries to assign a unicast destination to represent a one-to-many IPv4 video channel. The team should test joins and forwarding separately. What important rollout safeguard is most relevant here?

  1. Do not interpret (*,G) shared-tree membership as proof that a particular source is forwarding.
  2. Avoid using reserved link-local multicast groups for arbitrary enterprise streams.
  3. Do not disable loop-prevention checks simply to make unwanted multicast traffic pass.
  4. Do not assume PIM neighbor formation proves that hosts sent IGMP membership.

Explanation

Correct Answer

B:

For an enterprise telemetry network with multicast subscribers, the relevant safeguard is: Avoid using reserved link-local multicast groups for arbitrary enterprise streams. It matters while implementing: Allocate an appropriate multicast group address in a scope permitted for the enterprise distribution. The fault involves: IPv4 multicast traffic uses group addresses from 224.0.0.0 through 239.255.255.255 rather than ordinary unicast host destinations. The required acceptance result remains: Subscribers join the selected multicast group and receive matching test packets.

Incorrect Answers

A:

(S,G) multicast state identifies one particular source S and destination group G. The appropriate correction for the reported case is: Avoid using reserved link-local multicast groups for arbitrary enterprise streams.

C:

Multicast reverse-path forwarding verifies that a packet arrives via a valid route back toward its source or RP. Fixing that different mechanism would not address the current root cause: IPv4 multicast traffic uses group addresses from 224.0.0.0 through 239.255.255.255 rather than ordinary unicast host destinations.

D:

IGMP membership reports convey IPv4 receiver interest from hosts to their local multicast router. Its verification is distinct from the reported condition: An engineer tries to assign a unicast destination to represent a one-to-many IPv4 video channel. The team should test joins and forwarding separately.

Question 275

At a campus network built with Juniper EX switches, a Junos specialist investigates this scenario: A circuit works for short frames but drops full-size customer frames after stacked VLAN tagging is enabled. The intended segmentation and loop prevention must remain intact. When would the described mechanism be appropriate?

  1. Use filter-based VLAN classification when traffic attributes determine VLAN placement.
  2. Use loop protection where missing BPDUs could cause erroneous forwarding.
  3. Account for Q-in-Q encapsulation overhead when planning L2 transport MTU.
  4. Use Q-in-Q to transport customer VLAN tags through a provider Ethernet domain.

Explanation

Correct Answer

C:

For a campus network built with Juniper EX switches, this mechanism fits the requirement: Account for Q-in-Q encapsulation overhead when planning L2 transport MTU. The design is appropriate because: Adding an outer VLAN tag increases Ethernet frame size and may exceed an interface's supported MTU. In this scenario, the observed issue is: A circuit works for short frames but drops full-size customer frames after stacked VLAN tagging is enabled. The corresponding implementation is: Increase supported link MTU consistently or adjust customer frame limits where required.

Incorrect Answers

A:

Filter-based VLANs can classify ingress frames and assign eligible traffic to a selected VLAN. The appropriate correction for the reported case is: Increase supported link MTU consistently or adjust customer frame limits where required.

B:

Loop protection helps guard against unsafe port state changes when expected spanning-tree BPDUs disappear. Fixing that different mechanism would not address the current root cause: adding an outer VLAN tag increases Ethernet frame size and may exceed an interface's supported MTU.

D:

IEEE 802.1ad Q-in-Q encapsulates customer-tagged frames with an outer service VLAN tag. Its verification is distinct from the reported condition: A circuit works for short frames but drops full-size customer frames after stacked VLAN tagging is enabled. The intended segmentation and loop prevention must remain intact. When would the described mechanism be appropriate.

Question 276

At a dual-homed business network peering with two upstream providers, a Junos specialist investigates this scenario: An enterprise receives multiple paths from one neighboring AS and wants to influence which entry that AS uses. The routing policy must retain intended primary and backup paths. What is the most appropriate correction to implement?

  1. Apply a narrowly matched export policy for intended prefixes to the relevant BGP group.
  2. Choose exact or bounded prefix-length matching appropriate to the advertisement contract.
  3. Enable advertise-inactive only for the intentional peer context and test its effect.
  4. Apply intended MED values for comparable advertisements and validate the peer's MED treatment.

Explanation

Correct Answer

D:

For a dual-homed business network peering with two upstream providers, the direct corrective action is: Apply intended MED values for comparable advertisements and validate the peer's MED treatment. This addresses the mechanism: BGP MED can signal a preferred ingress point to a neighboring AS subject to the neighbor's selection policy. Confirm by checking: The cooperating neighbor selects the intended ingress for otherwise matching routes. During rollout, do not assume a remote AS must honor MED or compare MED across all unrelated ASes.

Incorrect Answers

A:

BGP export policy controls which eligible active routes the speaker announces to selected neighbors. The appropriate correction for the reported case is: Apply intended MED values for comparable advertisements and validate the peer's MED treatment.

B:

Junos route filters distinguish exact matching from longer or longer-prefix patterns. Fixing that different mechanism would not address the current root cause: BGP MED can signal a preferred ingress point to a neighboring AS subject to the neighbor's selection policy.

C:

Junos normally exports active routes; supported advertise-inactive can announce an eligible inactive BGP route in some cases. Its verification is distinct from the reported condition: An enterprise receives multiple paths from one neighboring AS and wants to influence which entry that AS uses. The routing policy must retain intended primary and backup paths.

Question 277

At a university separating multiple OSPF areas, a Junos specialist investigates this scenario: An OSPF neighbor remains in ExStart or Exchange although basic connectivity and Hellos work. The routing change must preserve control-plane consistency across areas. For which use case is this feature the best match?

  1. Use consistent link MTU to complete OSPF database-description synchronization.
  2. Prefer type-1 external metrics where internal distance to the ASBR must influence selection.
  3. Use a temporary virtual link when an OSPF backbone partition has a valid transit path.
  4. Use OSPF ABR summary policy to control which interarea prefixes propagate.

Explanation

Correct Answer

A:

For a university separating multiple OSPF areas, this mechanism fits the requirement: Use consistent link MTU to complete OSPF database-description synchronization. The design is appropriate because: Database-description exchange can fail when peers disagree on the IP MTU for a common OSPF link. In this scenario, the observed issue is: An OSPF neighbor remains in ExStart or Exchange although basic connectivity and Hellos work. The corresponding implementation is: Correct the relevant link MTU on both endpoints and restart adjacency safely if necessary.

Incorrect Answers

B:

Type-1 external OSPF cost includes internal cost to the ASBR while type-2 primarily uses the external metric for selection. The appropriate correction for the reported case is: Correct the relevant link MTU on both endpoints and restart adjacency safely if necessary.

C:

A supported OSPF virtual link can logically extend the backbone through a nonstub transit area between eligible ABRs. Fixing that different mechanism would not address the current root cause: database-description exchange can fail when peers disagree on the IP MTU for a common OSPF link.

D:

OSPF interarea summary-LSA generation can be governed with supported routing policies on ABRs. Its verification is distinct from the reported condition: An OSPF neighbor remains in ExStart or Exchange although basic connectivity and Hellos work. The routing change must preserve control-plane consistency across areas.

Question 278

At a regional provider operating Junos-based branch routers, a Junos specialist investigates this scenario: Many individual branch prefixes are announced between areas and inflate other areas' route tables. The team must validate neighbor state rather than assume basic IP reachability proves routing. What would demonstrate a successful correction under test?

  1. The expected interarea prefix LSA and remote IPv6 route appear in the intended area.
  2. Remote areas receive the expected summarized routes and excluded addresses do not blackhole.
  3. OSPF topology and route-change counters settle after fault correction.
  4. show ospf database and downstream routes reflect only the approved summaries.

Explanation

Correct Answer

B:

For a regional provider operating Junos-based branch routers, the decisive evidence is: Remote areas receive the expected summarized routes and excluded addresses do not blackhole. This validates the action: Configure appropriate ABR area-range summarization with valid aggregate boundaries. Because: An OSPF area border router can originate summarized interarea reachability when prefixes allow aggregation. An unrelated successful test would not prove this specific issue is resolved.

Incorrect Answers

A:

OSPFv3 interarea-prefix LSAs convey reachable IPv6 prefixes across area boundaries. The appropriate correction for the reported case is: Configure appropriate ABR area-range summarization with valid aggregate boundaries.

C:

Link-state SPF recalculation is triggered by topology changes and must converge over a coherent LSDB. Fixing that different mechanism would not address the current root cause: an OSPF area border router can originate summarized interarea reachability when prefixes allow aggregation.

D:

OSPF interarea summary-LSA generation can be governed with supported routing policies on ABRs. Its verification is distinct from the reported condition: Many individual branch prefixes are announced between areas and inflate other areas' route tables. The team must validate neighbor state rather than assume basic IP reachability proves routing.

Question 279

At a managed network team troubleshooting an internet edge, a Junos specialist investigates this scenario: Two BGP routes have equal local preference and AS-path length but differ in origin attribute. The diagnosis must distinguish a healthy BGP session from eligible received routes. Which limitation should guide the change control?

  1. Check local preference and next-hop reachability first because they can override this comparison.
  2. Avoid inserting a catchall accept before security and route-leak protections.
  3. Do not claim origin always wins over local preference or AS-path length.
  4. Test term ordering and default policy behavior before enabling changes on a production peer.

Explanation

Correct Answer

C:

For a managed network team troubleshooting an internet edge, the relevant safeguard is: Do not claim origin always wins over local preference or AS-path length. It matters while implementing: Inspect the origin attribute and apply policy only if the intended path requires explicit adjustment. The fault involves: BGP best-path selection considers origin type after higher-priority attributes, normally preferring IGP over EGP over incomplete. The required acceptance result remains: The best route matches documented origin comparison when other earlier criteria are tied.

Incorrect Answers

A:

In Junos BGP best-path selection an eligible shorter AS path is generally preferred after higher-priority criteria tie. The appropriate correction for the reported case is: Do not claim origin always wins over local preference or AS-path length.

B:

Junos policy terms are evaluated in configured order and a terminating action can end processing early. Fixing that different mechanism would not address the current root cause: BGP best-path selection considers origin type after higher-priority attributes, normally preferring IGP over EGP over incomplete.

D:

A BGP import policy determines which incoming route advertisements are accepted into the routing table. Its verification is distinct from the reported condition: Two BGP routes have equal local preference and AS-path length but differ in origin attribute. The diagnosis must distinguish a healthy BGP session from eligible received routes.

Question 280

At a campus network built with Juniper EX switches, a Junos specialist investigates this scenario: A switch interconnect passes one VLAN but drops frames for a second authorized VLAN. The intended segmentation and loop prevention must remain intact. When would the described mechanism be appropriate?

  1. Use MSTP instance mapping to scale spanning-tree topologies for many VLANs.
  2. Use filter-based VLAN classification when traffic attributes determine VLAN placement.
  3. Use access VLAN assignment for a single untagged user segment.
  4. Use tagged trunks to carry multiple VLANs between compatible switches.

Explanation

Correct Answer

D:

For a campus network built with Juniper EX switches, this mechanism fits the requirement: Use tagged trunks to carry multiple VLANs between compatible switches. The design is appropriate because: An Ethernet trunk carries selected tagged VLANs and membership must include every allowed VLAN. In this scenario, the observed issue is: A switch interconnect passes one VLAN but drops frames for a second authorized VLAN. The corresponding implementation is: Configure the required VLAN members on both ends of the tagged trunk.

Incorrect Answers

A:

Multiple Spanning Tree Protocol maps selected VLANs into common spanning-tree instances. The appropriate correction for the reported case is: Configure the required VLAN members on both ends of the tagged trunk.

B:

Filter-based VLANs can classify ingress frames and assign eligible traffic to a selected VLAN. Fixing that different mechanism would not address the current root cause: An Ethernet trunk carries selected tagged VLANs and membership must include every allowed VLAN.

C:

An untagged Ethernet access port places endpoint traffic into its configured access VLAN. Its verification is distinct from the reported condition: A switch interconnect passes one VLAN but drops frames for a second authorized VLAN. The intended segmentation and loop prevention must remain intact. When would the described mechanism be appropriate.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests