mcAfee Secure Website
exam =5
exam =6

Exam Code: JN0-650

Exam Name: Enterprise Routing and Switching, Professional (JNCIP-ENT)

Certification Provider: Juniper

Corresponding Certification: JNCIP-ENT

Juniper JN0-650 Questions & Answers

Reliable & Actual Study Materials for JN0-650 Exam Success

107 Questions & Answers with Testing Engine

"JN0-650: Enterprise Routing and Switching, Professional (JNCIP-ENT)" Testing Engine covers all the knowledge points of the real Juniper JN0-650 exam.

The latest actual JN0-650 Questions & Answers from Pass4sure. Everything you need to prepare and get best score at JN0-650 exam easily and quickly.

exam =7
Guarantee

Satisfaction Guaranteed

Pass4sure has a remarkable Juniper Candidate Success record. We're confident of our products and provide no hassle product exchange. That's how confident we are!

99.3% Pass Rate
Was: $137.49
Now: $124.99

Juniper JN0-650 Practice Test 27

Question 260

At a large enterprise updating redundant switch links, a Junos specialist investigates this scenario: Two adjacent switches use MSTP but appear to occupy different regions despite a shared physical trunk. The change must retain both link resilience and correct VLAN isolation. What is the most appropriate correction to implement?

  1. Assign the appropriate VLANs to the intended MST instances and set designated roots.
  2. Enable the supported L2PT mechanism for the selected customer control protocol and service VLAN.
  3. Configure supported VSTP membership and root priorities for the chosen VLANs.
  4. Align the MSTP region attributes and intended VLAN mappings across the switches.

Explanation

Correct Answer

D:

For a large enterprise updating redundant switch links, the direct corrective action is: Align the MSTP region attributes and intended VLAN mappings across the switches. This addresses the mechanism: MSTP region membership depends on compatible region name, revision and VLAN-to-instance mapping digest. Confirm by checking: Operational state shows common region information and expected instance boundaries. During rollout, avoid partial region updates that temporarily create different spanning-tree domains.

Incorrect Answers

A:

Multiple Spanning Tree Protocol maps selected VLANs into common spanning-tree instances. The appropriate correction for the reported case is: Align the MSTP region attributes and intended VLAN mappings across the switches.

B:

Layer 2 protocol tunneling can transport specified customer control frames across a separate provider bridging domain. Fixing that different mechanism would not address the current root cause: MSTP region membership depends on compatible region name, revision and VLAN-to-instance mapping digest.

C:

VLAN Spanning Tree Protocol allows separate tree instances for selected VLANs and can choose different roots. Its verification is distinct from the reported condition: Two adjacent switches use MSTP but appear to occupy different regions despite a shared physical trunk. The change must retain both link resilience and correct VLAN isolation.

Question 261

At a campus network built with Juniper EX switches, a Junos specialist investigates this scenario: An access switch unexpectedly becomes the root bridge and traffic takes a slow path through the campus. The intended segmentation and loop prevention must remain intact. What verification result should the engineer expect?

  1. show spanning-tree bridge identifies the intended root for each MST instance.
  2. show ethernet-switching interfaces displays the assigned VLAN and test hosts reach only its subnet.
  3. A controlled received-BPDU test produces the expected protective state and alert.
  4. Operational state shows common region information and expected instance boundaries.

Explanation

Correct Answer

A:

For a campus network built with Juniper EX switches, the decisive evidence is: show spanning-tree bridge identifies the intended root for each MST instance. This validates the action: Set supported bridge priorities so designated distribution switches become root and backup root. Because: Spanning-tree root selection uses bridge identifiers and configured priorities within the relevant instance. An unrelated successful test would not prove this specific issue is resolved.

Incorrect Answers

B:

An untagged Ethernet access port places endpoint traffic into its configured access VLAN. The appropriate correction for the reported case is: Set supported bridge priorities so designated distribution switches become root and backup root.

C:

BPDU protection can prevent an edge interface from accepting unauthorized bridge control messages. Fixing that different mechanism would not address the current root cause: spanning-tree root selection uses bridge identifiers and configured priorities within the relevant instance.

D:

MSTP region membership depends on compatible region name, revision and VLAN-to-instance mapping digest. Its verification is distinct from the reported condition: An access switch unexpectedly becomes the root bridge and traffic takes a slow path through the campus. The intended segmentation and loop prevention must remain intact.

Question 262

At a live-event venue using routed multicast streaming, a Junos specialist investigates this scenario: An enterprise deploys IPv6 group delivery but attempts to identify receivers with ordinary IPv6 unicast addresses. The change must preserve source identity and avoid multicast loops. Which underlying distinction should guide troubleshooting?

  1. PIM-SM can transition selected traffic from an RP-rooted shared tree to a source-rooted shortest-path tree.
  2. IPv6 multicast destinations begin in the FF00::/8 range and include scope information.
  3. IPv4 multicast traffic uses group addresses from 224.0.0.0 through 239.255.255.255 rather than ordinary unicast host destinations.
  4. PIM sparse mode builds multicast forwarding paths in response to explicit joins rather than flooding everywhere.

Explanation

Correct Answer

B:

For a live-event venue using routed multicast streaming, the governing mechanism is: IPv6 multicast destinations begin in the FF00::/8 range and include scope information. It explains the reported symptom: An enterprise deploys IPv6 group delivery but attempts to identify receivers with ordinary IPv6 unicast addresses. The intended response is: Select a suitable IPv6 multicast group and scope for the approved application. Verification: An eligible receiver joins the IPv6 multicast group and receives one expected copy.

Incorrect Answers

A:

PIM-SM can transition selected traffic from an RP-rooted shared tree to a source-rooted shortest-path tree. This alternative mechanism does not match the current fault.

C:

IPv4 multicast traffic uses group addresses from 224.0.0.0 through 239.255.255.255 rather than ordinary unicast host destinations. Fixing that different mechanism would not address the current root cause: IPv6 multicast destinations begin in the FF00::/8 range and include scope information.

D:

PIM sparse mode builds multicast forwarding paths in response to explicit joins rather than flooding everywhere. Its verification is distinct from the reported condition: An enterprise deploys IPv6 group delivery but attempts to identify receivers with ordinary IPv6 unicast addresses. The change must preserve source identity and avoid multicast loops.

Question 263

At a campus network built with Juniper EX switches, a Junos specialist investigates this scenario: Trunk links lack a recently introduced VLAN because the team expects dynamic VLAN registration without enabling a registration mechanism. The intended segmentation and loop prevention must remain intact. What is the most likely design-related cause?

  1. An Ethernet trunk carries selected tagged VLANs and membership must include every allowed VLAN.
  2. Layer 2 switches learn source MAC addresses on ingress ports and forward known unicast using their MAC tables.
  3. Multiple VLAN Registration Protocol exchanges VLAN registration information between participating bridged devices.
  4. Root protection can prevent a specified port from accepting an unexpected superior root advertisement.

Explanation

Correct Answer

C:

For a campus network built with Juniper EX switches, the governing mechanism is: Multiple VLAN Registration Protocol exchanges VLAN registration information between participating bridged devices. It explains the reported symptom: Trunk links lack a recently introduced VLAN because the team expects dynamic VLAN registration without enabling a registration mechanism. The intended response is: Enable supported MVRP on intended links and validate the dynamically registered VLAN membership. Verification: Both participating switches learn the correct registered VLAN and forward its traffic.

Incorrect Answers

A:

An Ethernet trunk carries selected tagged VLANs and membership must include every allowed VLAN. This alternative mechanism does not match the current fault.

B:

Layer 2 switches learn source MAC addresses on ingress ports and forward known unicast using their MAC tables. Fixing that different mechanism would not address the current root cause: multiple VLAN Registration Protocol exchanges VLAN registration information between participating bridged devices.

D:

Root protection can prevent a specified port from accepting an unexpected superior root advertisement. Its verification is distinct from the reported condition: Trunk links lack a recently introduced VLAN because the team expects dynamic VLAN registration without enabling a registration mechanism. The intended segmentation and loop prevention must remain intact.

Question 264

At a school building a restricted guest onboarding network, a Junos specialist investigates this scenario: An unmanaged visitor device does not answer 802.1X challenges yet should reach a limited onboarding network. Only approved identities may enter privileged enterprise segments. What important rollout safeguard is most relevant here?

  1. Protect shared secrets and ensure the RADIUS server permits the correct switch as a client.
  2. Do not grant full access merely because the client can exchange EAP packets.
  3. Do not confuse a server timeout with an explicit Access-Reject or permit a broad uncontrolled bypass.
  4. Do not assume a wrong-password response triggers the same behavior as complete nonresponse.

Explanation

Correct Answer

D:

For a school building a restricted guest onboarding network, the relevant safeguard is: Do not assume a wrong-password response triggers the same behavior as complete nonresponse. It matters while implementing: Configure supported guest VLAN behavior and its restricted connectivity policy on the access port. The fault involves: A guest VLAN can supply restricted access for supported nonresponsive clients when the authentication mode allows it. The required acceptance result remains: The unauthenticated nonresponsive test client reaches only the approved onboarding services.

Incorrect Answers

A:

In common 802.1X switching, the supplicant exchanges EAPOL with the authenticator, which relays authentication toward a RADIUS server. The appropriate correction for the reported case is: Do not assume a wrong-password response triggers the same behavior as complete nonresponse.

B:

A RADIUS Access-Reject event is distinct from a silent client and can be mapped to an appropriate reject VLAN. Fixing that different mechanism would not address the current root cause: a guest VLAN can supply restricted access for supported nonresponsive clients when the authentication mode allows it.

C:

Server fail fallback controls permit, deny, cached access or restricted VLAN assignment when authentication infrastructure is unavailable. Its verification is distinct from the reported condition: An unmanaged visitor device does not answer 802.1X challenges yet should reach a limited onboarding network. Only approved identities may enter privileged enterprise segments.

Question 265

At a campus switch team configuring Junos egress queues, a Junos specialist investigates this scenario: A low-latency voice service waits behind large file transfers even when its traffic is correctly classified. The improvement must not starve business traffic. Which underlying distinction should guide troubleshooting?

  1. A scheduler can prioritize selected latency-sensitive queues over other queues when the interface is congested.
  2. Shaping buffers excess eligible traffic to pace transmission whereas policing marks or drops traffic that exceeds a limit.
  3. Junos packet-loss priority provides an additional attribute for drop-profile selection under queue pressure.
  4. A behavior aggregate classifier maps incoming codepoint values to local forwarding class and loss priority.

Explanation

Correct Answer

A:

For a campus switch team configuring Junos egress queues, the governing mechanism is: A scheduler can prioritize selected latency-sensitive queues over other queues when the interface is congested. It explains the reported symptom: A low-latency voice service waits behind large file transfers even when its traffic is correctly classified. The intended response is: Configure an appropriate constrained high-priority scheduler for the approved real-time class. Verification: Voice queue delay remains within the target while lower classes still receive required service.

Incorrect Answers

B:

Shaping buffers excess eligible traffic to pace transmission whereas policing marks or drops traffic that exceeds a limit. This alternative mechanism does not match the current fault.

C:

Junos packet-loss priority provides an additional attribute for drop-profile selection under queue pressure. Fixing that different mechanism would not address the current root cause: a scheduler can prioritize selected latency-sensitive queues over other queues when the interface is congested.

D:

A behavior aggregate classifier maps incoming codepoint values to local forwarding class and loss priority. Its verification is distinct from the reported condition: A low-latency voice service waits behind large file transfers even when its traffic is correctly classified. The improvement must not starve business traffic.

Question 266

At a provider Ethernet network carrying customer Layer 2 services, a Junos specialist investigates this scenario: A desktop plugged into an EX switch receives traffic from an unexpected user VLAN. The service must preserve tags without bridging unrelated tenants. For which use case is this feature the best match?

  1. Use a private VLAN promiscuous port to provide common gateway access.
  2. Use access VLAN assignment for a single untagged user segment.
  3. Use filter-based VLAN classification when traffic attributes determine VLAN placement.
  4. Use MSTP instance mapping to scale spanning-tree topologies for many VLANs.

Explanation

Correct Answer

B:

For a provider Ethernet network carrying customer Layer 2 services, this mechanism fits the requirement: Use access VLAN assignment for a single untagged user segment. The design is appropriate because: An untagged Ethernet access port places endpoint traffic into its configured access VLAN. In this scenario, the observed issue is: A desktop plugged into an EX switch receives traffic from an unexpected user VLAN. The corresponding implementation is: Set the intended VLAN membership on the access logical interface and verify the port mode.

Incorrect Answers

A:

Private VLAN promiscuous ports can communicate with applicable secondary VLAN ports, providing a shared exit. The appropriate correction for the reported case is: Set the intended VLAN membership on the access logical interface and verify the port mode.

C:

Filter-based VLANs can classify ingress frames and assign eligible traffic to a selected VLAN. Fixing that different mechanism would not address the current root cause: an untagged Ethernet access port places endpoint traffic into its configured access VLAN.

D:

Multiple Spanning Tree Protocol maps selected VLANs into common spanning-tree instances. Its verification is distinct from the reported condition: A desktop plugged into an EX switch receives traffic from an unexpected user VLAN. The service must preserve tags without bridging unrelated tenants.

Question 267

At a university separating multiple OSPF areas, a Junos specialist investigates this scenario: A route is visible locally but network engineers confuse accepting it into a RIB with advertising it as a new OSPF external LSA. The routing change must preserve control-plane consistency across areas. What would demonstrate a successful correction under test?

  1. The selected destination shows multiple eligible next hops and traffic load sharing is observable.
  2. show route protocol ospf on another router reveals the advertised external prefix.
  3. The intended external LSA appears only after the correct export policy is active.
  4. Other OSPFv3 routers learn the specified external IPv6 prefix without unrelated statics.

Explanation

Correct Answer

C:

For a university separating multiple OSPF areas, the decisive evidence is: The intended external LSA appears only after the correct export policy is active. This validates the action: Apply the policy at the hierarchy appropriate to redistribution rather than assuming import creates advertisements. Because: Junos OSPF export governs eligible external route origination while import filtering has different route-selection effects. An unrelated successful test would not prove this specific issue is resolved.

Incorrect Answers

A:

OSPF can compute equal-cost paths; forwarding utilization depends on installed next hops and platform ECMP behavior. The appropriate correction for the reported case is: Apply the policy at the hierarchy appropriate to redistribution rather than assuming import creates advertisements.

B:

Junos OSPF normally requires explicit export policy to redistribute eligible non-OSPF routes as external reachability. Fixing that different mechanism would not address the current root cause: junos OSPF export governs eligible external route origination while import filtering has different route-selection effects.

D:

Junos requires a suitable route export policy to originate eligible non-OSPFv3 routes. Its verification is distinct from the reported condition: A route is visible locally but network engineers confuse accepting it into a RIB with advertising it as a new OSPF external LSA. The routing change must preserve control-plane consistency across areas.

Question 268

At a multihomed data center using redundant Ethernet segments, a Junos specialist investigates this scenario: Two VTEPs reach each other but a tenant VLAN crosses into the wrong remote Ethernet segment. The design must avoid forwarding loops during failover. For which use case is this feature the best match?

  1. Use routable VTEP loopbacks and healthy underlay routing to carry VXLAN encapsulated frames.
  2. Use EVPN split horizon to prevent bridging loops across dual-homed Ethernet segments.
  3. Account for VXLAN header overhead when sizing underlay MTU.
  4. Use consistent VNIs to extend a selected VLAN across a VXLAN fabric.

Explanation

Correct Answer

D:

For a multihomed data center using redundant Ethernet segments, this mechanism fits the requirement: Use consistent VNIs to extend a selected VLAN across a VXLAN fabric. The design is appropriate because: VXLAN uses a 24-bit VNI to identify a logical overlay segment associated with local bridging context. In this scenario, the observed issue is: Two VTEPs reach each other but a tenant VLAN crosses into the wrong remote Ethernet segment. The corresponding implementation is: Align the intended VLAN-to-VNI mapping across participating leaf switches.

Incorrect Answers

A:

VXLAN tunnels require IP reachability between VTEP addresses and adequate underlay transport capacity. The appropriate correction for the reported case is: Align the intended VLAN-to-VNI mapping across participating leaf switches.

B:

EVPN multihoming split-horizon mechanisms prevent reflected traffic from looping across a common Ethernet segment. Fixing that different mechanism would not address the current root cause: VXLAN uses a 24-bit VNI to identify a logical overlay segment associated with local bridging context.

C:

VXLAN adds outer Ethernet, IP, UDP and VXLAN encapsulation overhead to tenant frames. Its verification is distinct from the reported condition: Two VTEPs reach each other but a tenant VLAN crosses into the wrong remote Ethernet segment. The design must avoid forwarding loops during failover.

Question 269

At a healthcare organization connecting redundant facilities, a Junos specialist investigates this scenario: Routers report Full neighbors but one route is missing and technicians only inspect the forwarding table. The correction must not expose administrative network prefixes. For which use case is this feature the best match?

  1. Use OSPF LSDB inspection before changing unrelated next-hop forwarding settings.
  2. Use area 0 as the backbone of a multi-area OSPF routing domain.
  3. Use SPF diagnostics to identify repeated topology-triggered route recalculation.
  4. Use a temporary virtual link when an OSPF backbone partition has a valid transit path.

Explanation

Correct Answer

A:

For a healthcare organization connecting redundant facilities, this mechanism fits the requirement: Use OSPF LSDB inspection before changing unrelated next-hop forwarding settings. The design is appropriate because: The link-state database and area LSA contents determine which routes the OSPF calculation can derive. In this scenario, the observed issue is: Routers report Full neighbors but one route is missing and technicians only inspect the forwarding table. The corresponding implementation is: Compare show ospf database and LSAs against the intended origin and area boundaries.

Incorrect Answers

B:

OSPF interarea routing normally relies on connectivity through area 0 and correctly placed area border routers. The appropriate correction for the reported case is: Compare show ospf database and LSAs against the intended origin and area boundaries.

C:

Link-state SPF recalculation is triggered by topology changes and must converge over a coherent LSDB. Fixing that different mechanism would not address the current root cause: the link-state database and area LSA contents determine which routes the OSPF calculation can derive.

D:

A supported OSPF virtual link can logically extend the backbone through a nonstub transit area between eligible ABRs. Its verification is distinct from the reported condition: Routers report Full neighbors but one route is missing and technicians only inspect the forwarding table. The correction must not expose administrative network prefixes.

Question 270

At an enterprise core exchanging BGP routes over redundant WAN paths, a Junos specialist investigates this scenario: An iBGP session over loopbacks fails because the outgoing TCP connection uses a physical-interface source address. The chosen route must have a valid data-plane next hop. Which configuration adjustment should be made first to address this issue?

  1. Correct the unintended AS-path manipulation or routing leak rather than disabling loop protection.
  2. Set the BGP local-address to the intended routable loopback and verify remote peer configuration.
  3. Apply targeted AS-path prepend in an authorized export policy for the backup link.
  4. Review peer type and the complete path decision chain before adjusting selection policy.

Explanation

Correct Answer

B:

For an enterprise core exchanging BGP routes over redundant WAN paths, the direct corrective action is: Set the BGP local-address to the intended routable loopback and verify remote peer configuration. This addresses the mechanism: Both ends of a loopback-based BGP session must reach and recognize the configured local addresses. Confirm by checking: show BGP neighbor reports the expected local source and established peer endpoint. During rollout, ensure underlay IGP reachability to loopbacks before pinning the session source.

Incorrect Answers

A:

BGP AS-path loop detection normally prevents accepting routes already traversing the local autonomous system. The appropriate correction for the reported case is: Set the BGP local-address to the intended routable loopback and verify remote peer configuration.

C:

AS-path prepending lengthens a path in selected outbound advertisements and may influence upstream BGP selection. Fixing that different mechanism would not address the current root cause: both ends of a loopback-based BGP session must reach and recognize the configured local addresses.

D:

Junos BGP best-path logic generally prefers the external route when preceding comparisons tie. Its verification is distinct from the reported condition: An iBGP session over loopbacks fails because the outgoing TCP connection uses a physical-interface source address. The chosen route must have a valid data-plane next hop.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests