mcAfee Secure Website
exam =5
exam =6

Exam Code: JN0-650

Exam Name: Enterprise Routing and Switching, Professional (JNCIP-ENT)

Certification Provider: Juniper

Corresponding Certification: JNCIP-ENT

Juniper JN0-650 Questions & Answers

Reliable & Actual Study Materials for JN0-650 Exam Success

107 Questions & Answers with Testing Engine

"JN0-650: Enterprise Routing and Switching, Professional (JNCIP-ENT)" Testing Engine covers all the knowledge points of the real Juniper JN0-650 exam.

The latest actual JN0-650 Questions & Answers from Pass4sure. Everything you need to prepare and get best score at JN0-650 exam easily and quickly.

exam =7
Guarantee

Satisfaction Guaranteed

Pass4sure has a remarkable Juniper Candidate Success record. We're confident of our products and provide no hassle product exchange. That's how confident we are!

99.3% Pass Rate
Was: $137.49
Now: $124.99

Juniper JN0-650 Practice Test 15

Question 140

At an enterprise migrating virtual machines between racks, a Junos specialist investigates this scenario: An overlay needs to advertise routed IP subnet reachability without enumerating every individual host MAC. The overlay must relearn host reachability without stale tunnel selection. What is the most appropriate correction to implement?

  1. Enable a supported EVPN BGP signaling relationship with the intended route targets and instances.
  2. Set approved export and import route targets for each isolated tenant EVPN service.
  3. Verify the local MAC/IP advertisement and its acceptance through the correct EVPN instance.
  4. Advertise the intended IP prefixes through an eligible EVPN routing instance and import targets.

Explanation

Correct Answer

D:

For an enterprise migrating virtual machines between racks, the direct corrective action is: Advertise the intended IP prefixes through an eligible EVPN routing instance and import targets. This addresses the mechanism: EVPN route type 5 conveys IP prefix reachability and can support routed overlay designs. Confirm by checking: The remote IP-VRF learns the approved prefix with valid overlay next-hop resolution. During rollout, verify IRB and route-target configuration and avoid leaking unrelated tenant subnets.

Incorrect Answers

A:

EVPN uses a BGP signaling address family to distribute Ethernet reachability and related control-plane information. The appropriate correction for the reported case is: Advertise the intended IP prefixes through an eligible EVPN routing instance and import targets.

B:

EVPN route targets determine which routes are imported into the relevant EVPN instances and tenant contexts. Fixing that different mechanism would not address the current root cause: EVPN route type 5 conveys IP prefix reachability and can support routed overlay designs.

C:

EVPN route type 2 advertises MAC reachability and can include associated IP information for hosts. Its verification is distinct from the reported condition: An overlay needs to advertise routed IP subnet reachability without enumerating every individual host MAC. The overlay must relearn host reachability without stale tunnel selection.

Question 141

At a live-event venue using routed multicast streaming, a Junos specialist investigates this scenario: An ASM receiver joins a group without selecting one specific sender but engineers search only (S,G) entries. The change must preserve source identity and avoid multicast loops. Which configuration adjustment should be made first to address this issue?

  1. Verify receiver joins and the relevant shared-tree multicast state toward the RP.
  2. Configure or correct the intended RP mapping for the affected group range throughout the domain.
  3. Inspect the source and group state to diagnose the correct sender-specific distribution tree.
  4. Enable compatible PIM on the appropriate routed interfaces and allow required multicast control traffic.

Explanation

Correct Answer

A:

For a live-event venue using routed multicast streaming, the direct corrective action is: Verify receiver joins and the relevant shared-tree multicast state toward the RP. This addresses the mechanism: Shared-tree (*,G) state expresses interest in traffic to group G from potentially multiple sources. Confirm by checking: The network reports expected (*,G) membership and delivers approved ASM traffic. During rollout, check the RP mapping before assuming a source-specific join is mandatory for ASM.

Incorrect Answers

B:

PIM-SM shared-tree construction depends on consistent mappings of multicast groups to suitable RPs. The appropriate correction for the reported case is: Verify receiver joins and the relevant shared-tree multicast state toward the RP.

C:

(S,G) multicast state identifies one particular source S and destination group G. Fixing that different mechanism would not address the current root cause: shared-tree (*,G) state expresses interest in traffic to group G from potentially multiple sources.

D:

PIM routers discover routing neighbors on participating interfaces through PIM Hello exchanges. Its verification is distinct from the reported condition: An ASM receiver joins a group without selecting one specific sender but engineers search only (S,G) entries. The change must preserve source identity and avoid multicast loops.

Question 142

At a data-center access fabric using tagged trunks, a Junos specialist investigates this scenario: Isolated private VLAN endpoints can reach neither each other nor the legitimate default gateway. The proposed behavior must be validated on actual switching ports. When would the described mechanism be appropriate?

  1. Use private VLAN isolated ports for same-subnet tenant isolation.
  2. Use a private VLAN promiscuous port to provide common gateway access.
  3. Use family ethernet-switching on supported switch logical interfaces.
  4. Use MSTP to preserve redundancy without Layer 2 forwarding loops.

Explanation

Correct Answer

B:

For a data-center access fabric using tagged trunks, this mechanism fits the requirement: Use a private VLAN promiscuous port to provide common gateway access. The design is appropriate because: Private VLAN promiscuous ports can communicate with applicable secondary VLAN ports, providing a shared exit. In this scenario, the observed issue is: Isolated private VLAN endpoints can reach neither each other nor the legitimate default gateway. The corresponding implementation is: Configure the gateway-facing port with proper promiscuous association for the private VLAN topology.

Incorrect Answers

A:

Private VLAN isolated ports restrict communication with peer isolated ports while allowing designated promiscuous connectivity. The appropriate correction for the reported case is: Configure the gateway-facing port with proper promiscuous association for the private VLAN topology.

C:

Junos enhanced Layer 2 switching uses family ethernet-switching configuration on eligible logical interfaces. Fixing that different mechanism would not address the current root cause: private VLAN promiscuous ports can communicate with applicable secondary VLAN ports, providing a shared exit.

D:

Spanning tree prevents bridging loops by keeping appropriate redundant ports in nondesignated states. Its verification is distinct from the reported condition: Isolated private VLAN endpoints can reach neither each other nor the legitimate default gateway. The proposed behavior must be validated on actual switching ports. When would the described mechanism be appropriate.

Question 143

At an enterprise telemetry network with multicast subscribers, a Junos specialist investigates this scenario: A multicast video stream floods every port in a VLAN although only two receivers joined. The team should test joins and forwarding separately. For which use case is this feature the best match?

  1. Use multicast source-group policy to restrict who may deliver group traffic.
  2. Use PIM Register messages to introduce ASM sources to a rendezvous point.
  3. Use IGMP snooping to constrain Layer 2 multicast distribution to interested ports.
  4. Use an IGMP querier to maintain receiver state in a multicast VLAN.

Explanation

Correct Answer

C:

For an enterprise telemetry network with multicast subscribers, this mechanism fits the requirement: Use IGMP snooping to constrain Layer 2 multicast distribution to interested ports. The design is appropriate because: IGMP snooping lets a Layer 2 switch learn interested receiver ports and limit multicast flooding within a VLAN. In this scenario, the observed issue is: A multicast video stream floods every port in a VLAN although only two receivers joined. The corresponding implementation is: Configure supported IGMP snooping and verify a reachable multicast-router port in the receiver VLAN.

Incorrect Answers

A:

PIM and multicast routing policy can be applied to limit permitted source and group reachability. The appropriate correction for the reported case is: Configure supported IGMP snooping and verify a reachable multicast-router port in the receiver VLAN.

B:

In PIM sparse-mode ASM, a first-hop designated router can register new source traffic with the RP. Fixing that different mechanism would not address the current root cause: IGMP snooping lets a Layer 2 switch learn interested receiver ports and limit multicast flooding within a VLAN.

D:

IGMP membership maintenance relies on periodic queries from a suitable multicast querier. Its verification is distinct from the reported condition: A multicast video stream floods every port in a VLAN although only two receivers joined. The team should test joins and forwarding separately.

Question 144

At a dual-homed business network peering with two upstream providers, a Junos specialist investigates this scenario: A route filter intended to allow a single aggregate accidentally accepts many more-specific customer prefixes. The routing policy must retain intended primary and backup paths. Which design objective is best served by this mechanism?

  1. Use BGP ORIGIN as a later best-path tiebreaker among otherwise comparable paths.
  2. Use BGP route reflectors to scale internal route distribution beyond a full mesh.
  3. Use BGP prefix limits to protect route-table capacity from excessive peer announcements.
  4. Use route-filter match semantics to prevent unintended more-specific route leaks.

Explanation

Correct Answer

D:

For a dual-homed business network peering with two upstream providers, this mechanism fits the requirement: Use route-filter match semantics to prevent unintended more-specific route leaks. The design is appropriate because: Junos route filters distinguish exact matching from longer or longer-prefix patterns. In this scenario, the observed issue is: A route filter intended to allow a single aggregate accidentally accepts many more-specific customer prefixes. The corresponding implementation is: Choose exact or bounded prefix-length matching appropriate to the advertisement contract.

Incorrect Answers

A:

BGP best-path selection considers origin type after higher-priority attributes, normally preferring IGP over EGP over incomplete. The appropriate correction for the reported case is: Choose exact or bounded prefix-length matching appropriate to the advertisement contract.

B:

Ordinary iBGP split-horizon rules avoid re-advertising routes between iBGP peers; route reflectors provide controlled reflection. Fixing that different mechanism would not address the current root cause: junos route filters distinguish exact matching from longer or longer-prefix patterns.

C:

A BGP prefix-limit control detects or constrains excessive received NLRI from a peer. Its verification is distinct from the reported condition: A route filter intended to allow a single aggregate accidentally accepts many more-specific customer prefixes. The routing policy must retain intended primary and backup paths.

Question 145

At a regional provider operating Junos-based branch routers, a Junos specialist investigates this scenario: An OSPFv3 ABR has an IPv6 subnet internally but other areas never learn the prefix. The team must validate neighbor state rather than assume basic IP reachability proves routing. Which limitation should guide the change control?

  1. Avoid applying IPv4 OSPF LSA type assumptions to OSPFv3 packet formats.
  2. Verify IPv6 link-local interface reachability and security filters before assuming IPv4 OSPF proves readiness.
  3. Avoid enabling ECMP across paths with incompatible MTU or traffic-security policies.
  4. Coordinate key rotation to avoid simultaneous loss of all redundant routing adjacencies.

Explanation

Correct Answer

A:

For a regional provider operating Junos-based branch routers, the relevant safeguard is: Avoid applying IPv4 OSPF LSA type assumptions to OSPFv3 packet formats. It matters while implementing: Check ABR area topology and permitted interarea prefix advertisement for the missing network. The fault involves: OSPFv3 interarea-prefix LSAs convey reachable IPv6 prefixes across area boundaries. The required acceptance result remains: The expected interarea prefix LSA and remote IPv6 route appear in the intended area.

Incorrect Answers

B:

OSPFv3 is a distinct link-state protocol requiring correct interface and area enablement for IPv6 environments. The appropriate correction for the reported case is: Avoid applying IPv4 OSPF LSA type assumptions to OSPFv3 packet formats.

C:

OSPF can compute equal-cost paths; forwarding utilization depends on installed next hops and platform ECMP behavior. Fixing that different mechanism would not address the current root cause: OSPFv3 interarea-prefix LSAs convey reachable IPv6 prefixes across area boundaries.

D:

OSPF protocol authentication checks configured credentials for applicable neighbor exchanges. Its verification is distinct from the reported condition: An OSPFv3 ABR has an IPv6 subnet internally but other areas never learn the prefix. The team must validate neighbor state rather than assume basic IP reachability proves routing.

Question 146

At an enterprise core exchanging BGP routes over redundant WAN paths, a Junos specialist investigates this scenario: An iBGP speaker advertises a learned external prefix but internal clients cannot reach the external provider next hop. The chosen route must have a valid data-plane next hop. What is the most appropriate correction to implement?

  1. Enable matching supported BGP authentication keys on both sides and test staged replacement.
  2. Apply approved next-hop self behavior at the correct iBGP advertisement boundary.
  3. Repair the underlay route to the received BGP next hop or apply a deliberate next-hop policy.
  4. Choose exact or bounded prefix-length matching appropriate to the advertisement contract.

Explanation

Correct Answer

B:

For an enterprise core exchanging BGP routes over redundant WAN paths, the direct corrective action is: Apply approved next-hop self behavior at the correct iBGP advertisement boundary. This addresses the mechanism: iBGP propagation may retain the original eBGP next-hop attribute unless policy or configuration changes it. Confirm by checking: Internal routers resolve the advertised next hop through the enterprise IGP and can forward to the prefix. During rollout, confirm the advertising router actually has valid egress before making it a transit hop.

Incorrect Answers

A:

Compatible TCP-level BGP authentication methods can verify the configured neighbor relationship. The appropriate correction for the reported case is: Apply approved next-hop self behavior at the correct iBGP advertisement boundary.

C:

A usable BGP route requires an eligible reachable forwarding next hop before it can become active. Fixing that different mechanism would not address the current root cause: iBGP propagation may retain the original eBGP next-hop attribute unless policy or configuration changes it.

D:

Junos route filters distinguish exact matching from longer or longer-prefix patterns. Its verification is distinct from the reported condition: An iBGP speaker advertises a learned external prefix but internal clients cannot reach the external provider next hop. The chosen route must have a valid data-plane next hop.

Question 147

At a provider Ethernet network carrying customer Layer 2 services, a Junos specialist investigates this scenario: A unicast frame is flooded across a VLAN because the switch lacks a destination MAC entry. The service must preserve tags without bridging unrelated tenants. Which operational change most directly resolves the observed failure?

  1. Align the MSTP region attributes and intended VLAN mappings across the switches.
  2. Configure supported LACP or static aggregated Ethernet on both ends as appropriate.
  3. Verify MAC learning and the relevant source port/VLAN association.
  4. Enable the supported BPDU protection behavior on designated host-facing ports.

Explanation

Correct Answer

C:

For a provider Ethernet network carrying customer Layer 2 services, the direct corrective action is: Verify MAC learning and the relevant source port/VLAN association. This addresses the mechanism: Layer 2 switches learn source MAC addresses on ingress ports and forward known unicast using their MAC tables. Confirm by checking: show ethernet-switching table contains the expected MAC-to-port entry and forwarding becomes selective. During rollout, check MAC aging and port movement before pinning static entries.

Incorrect Answers

A:

MSTP region membership depends on compatible region name, revision and VLAN-to-instance mapping digest. The appropriate correction for the reported case is: Verify MAC learning and the relevant source port/VLAN association.

B:

A link aggregation group presents multiple member links as one logical Ethernet interface when both peers agree. Fixing that different mechanism would not address the current root cause: layer 2 switches learn source MAC addresses on ingress ports and forward known unicast using their MAC tables.

D:

BPDU protection can prevent an edge interface from accepting unauthorized bridge control messages. Its verification is distinct from the reported condition: A unicast frame is flooded across a VLAN because the switch lacks a destination MAC entry. The service must preserve tags without bridging unrelated tenants.

Question 148

At a branch router serving several application classes, a Junos specialist investigates this scenario: Users report poor application performance but staff rely solely on interface utilization and ignore per-queue drops. The team must validate packet drops by actual queue statistics. What is the most likely design-related cause?

  1. Rate policers use token or burst parameters that influence which short bursts are considered conformant.
  2. Junos rewrite rules map internal forwarding class and loss-priority information to outgoing packet codepoints.
  3. The ingress trust boundary decides whether external markings should be accepted or reclassified.
  4. Per-queue counters reveal forwarding class use, transmission and discard behavior during congestion.

Explanation

Correct Answer

D:

For a branch router serving several application classes, the governing mechanism is: Per-queue counters reveal forwarding class use, transmission and discard behavior during congestion. It explains the reported symptom: Users report poor application performance but staff rely solely on interface utilization and ignore per-queue drops. The intended response is: Inspect Junos interface queue statistics and correlate drops with traffic class and times. Verification: A representative load shows which class drops packets and the verified correction reduces them.

Incorrect Answers

A:

Rate policers use token or burst parameters that influence which short bursts are considered conformant. This alternative mechanism does not match the current fault.

B:

Junos rewrite rules map internal forwarding class and loss-priority information to outgoing packet codepoints. Fixing that different mechanism would not address the current root cause: per-queue counters reveal forwarding class use, transmission and discard behavior during congestion.

C:

The ingress trust boundary decides whether external markings should be accepted or reclassified. Its verification is distinct from the reported condition: Users report poor application performance but staff rely solely on interface utilization and ignore per-queue drops. The team must validate packet drops by actual queue statistics.

Question 149

At a provider Ethernet network carrying customer Layer 2 services, a Junos specialist investigates this scenario: A switch's MSTP region connects to a different spanning-tree domain and path selection behaves unexpectedly. The service must preserve tags without bridging unrelated tenants. Which configuration adjustment should be made first to address this issue?

  1. Inspect boundary-port roles and configure supported interoperation at the domain edge.
  2. Assign distinct outer service VLAN identities to the independent customer services.
  3. Align the MSTP region attributes and intended VLAN mappings across the switches.
  4. Enable a consistent MSTP topology and verify the expected alternate-port state.

Explanation

Correct Answer

A:

For a provider Ethernet network carrying customer Layer 2 services, the direct corrective action is: Inspect boundary-port roles and configure supported interoperation at the domain edge. This addresses the mechanism: MSTP region boundaries interact with neighboring spanning-tree variants through common spanning-tree behavior. Confirm by checking: Root and port states remain stable on both sides during controlled link transitions. During rollout, do not assume per-instance MST details traverse an incompatible external region unchanged.

Incorrect Answers

B:

A provider S-VLAN or equivalent encapsulation boundary is needed to keep identical customer C-VLAN numbers separate. The appropriate correction for the reported case is: Inspect boundary-port roles and configure supported interoperation at the domain edge.

C:

MSTP region membership depends on compatible region name, revision and VLAN-to-instance mapping digest. Fixing that different mechanism would not address the current root cause: MSTP region boundaries interact with neighboring spanning-tree variants through common spanning-tree behavior.

D:

Spanning tree prevents bridging loops by keeping appropriate redundant ports in nondesignated states. Its verification is distinct from the reported condition: A switch's MSTP region connects to a different spanning-tree domain and path selection behaves unexpectedly. The service must preserve tags without bridging unrelated tenants.

Question 150

At a medical facility deploying high-power conference phones, a Junos specialist investigates this scenario: A phone's integrated PC switch port works but the downstream computer never reaches the data VLAN. The phone network must retain appropriate VLAN and voice QoS treatment. For which use case is this feature the best match?

  1. Use LLDP to discover directly connected Ethernet neighbors.
  2. Use a dual-use access port to serve an IP phone plus an attached workstation.
  3. Use PoE classification to allocate suitable endpoint power safely.
  4. Use LLDP power negotiation for compatible phones with varying power requirements.

Explanation

Correct Answer

B:

For a medical facility deploying high-power conference phones, this mechanism fits the requirement: Use a dual-use access port to serve an IP phone plus an attached workstation. The design is appropriate because: An Ethernet phone can bridge tagged voice traffic and untagged workstation traffic with appropriate VLAN behavior. In this scenario, the observed issue is: A phone's integrated PC switch port works but the downstream computer never reaches the data VLAN. The corresponding implementation is: Validate the phone passthrough configuration and Junos port VLAN membership for both traffic types.

Incorrect Answers

A:

Link Layer Discovery Protocol advertises local chassis and port information to directly attached compatible devices. The appropriate correction for the reported case is: Validate the phone passthrough configuration and Junos port VLAN membership for both traffic types.

C:

PoE power classification informs the power source of the powered device's required allocation. Fixing that different mechanism would not address the current root cause: An Ethernet phone can bridge tagged voice traffic and untagged workstation traffic with appropriate VLAN behavior.

D:

Supported LLDP-MED or LLDP power TLVs can negotiate endpoint power requirements beyond static class assumptions. Its verification is distinct from the reported condition: A phone's integrated PC switch port works but the downstream computer never reaches the data VLAN. The phone network must retain appropriate VLAN and voice QoS treatment.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests