mcAfee Secure Website
exam =5
exam =6

Exam Code: NSE4_FGT_AD-7.6

Exam Name: Fortinet NSE 4 - FortiOS 7.6 Administrator

Certification Provider: Fortinet

Corresponding Certification: NSE4

Fortinet NSE4_FGT_AD-7.6 Questions & Answers

Reliable & Actual Study Materials for NSE4_FGT_AD-7.6 Exam Success

94 Questions & Answers with Testing Engine

"NSE4_FGT_AD-7.6: Fortinet NSE 4 - FortiOS 7.6 Administrator" Testing Engine covers all the knowledge points of the real Fortinet NSE4_FGT_AD-7.6 exam.

The latest actual NSE4_FGT_AD-7.6 Questions & Answers from Pass4sure. Everything you need to prepare and get best score at NSE4_FGT_AD-7.6 exam easily and quickly.

exam =7
Guarantee

Satisfaction Guaranteed

Pass4sure has a remarkable Fortinet Candidate Success record. We're confident of our products and provide no hassle product exchange. That's how confident we are!

99.3% Pass Rate
Was: $137.49
Now: $124.99

Fortinet NSE4_FGT_AD-7.6 Practice Test 54

Question 530

Two FortiGates establish an IPsec tunnel but business traffic fails. The observed symptom is that phase 2 counters show encrypt bytes increasing but decrypt bytes remain zero. Which diagnostic step best resolves the uncertainty?

  1. Check remote routing, selectors, remote policies and return path rather than assuming local encryption is broken
  2. Add the reciprocal remote-side route for the local protected network
  3. Create an appropriate scoped inside-to-IPsec firewall allow policy
  4. Exclude the site-to-site protected traffic from inappropriate source NAT

Explanation

Correct Answer

A:

The appropriate control is to check remote routing, selectors, remote policies and return path rather than assuming local encryption is broken. A one-way counter pattern indicates traffic leaves the local tunnel without the expected reply.

Incorrect Answers

B:

Add the reciprocal remote-side route for the local protected network is relevant when remote replies never reach the initiating site because remote return routing is missing. A functioning tunnel requires routes in both directions.

C:

Create an appropriate scoped inside-to-IPsec firewall allow policy is useful when the local route uses the tunnel but firewall forward policy denies the protected traffic. A route-based tunnel still needs security policy authorization for protected packets.

D:

Exclude the site-to-site protected traffic from inappropriate source NAT addresses a different symptom: a generic internet SNAT rule matches traffic intended for a selector requiring private source addresses. NAT can change source addresses so they no longer match expected IPsec selectors.

Question 531

A FortiGate behind an ISP gateway establishes IPsec with a public peer. In the effective configuration, IKE messages cross an intermediate NAT device but ESP traffic fails. Which control most directly addresses the observed gap?

  1. Enable compatible NAT traversal and confirm UDP 4500 reachability
  2. Configure unique supported peer IDs and matching dial-up or gateway selectors
  3. Use a supported dynamic-peer design and validate keepalive behavior
  4. Check external NAT mapping and the configured peer identification

Explanation

Correct Answer

A:

Enable compatible NAT traversal and confirm UDP 4500 reachability directly addresses the requirement. NAT-T encapsulates ESP in UDP to work through NAT devices.

Incorrect Answers

B:

Configure unique supported peer IDs and matching dial-up or gateway selectors is relevant when two branch gateways sit behind one NAT public IP and use overlapping identifiers. Peer identity and connection profiles must disambiguate multiple protected peers.

C:

Use a supported dynamic-peer design and validate keepalive behavior is useful when a tunnel works until a home router changes its public NAT mapping. Fixed-public-IP assumptions do not hold for frequently changing NAT endpoints.

D:

Check external NAT mapping and the configured peer identification addresses a different symptom: a peer reports the private source address rather than the public address expected by a fixed-gateway configuration. Remote gateway expectations must match the reachable translated endpoint and identity.

Question 532

A FortiGate behind an ISP gateway establishes IPsec with a public peer. The current operating problem is that UDP 500 reaches the peer but the intermediate firewall blocks UDP 4500 during NAT detection. Which response is most effective for this case?

  1. Use a supported dynamic-peer design and validate keepalive behavior
  2. Configure unique supported peer IDs and matching dial-up or gateway selectors
  3. Enable compatible NAT traversal and confirm UDP 4500 reachability
  4. Permit the required NAT-T UDP 4500 path between gateways

Explanation

Correct Answer

D:

Permit the required NAT-T UDP 4500 path between gateways is the best response. IPsec negotiation can transition transport ports when NAT is detected.

Incorrect Answers

A:

Use a supported dynamic-peer design and validate keepalive behavior is relevant when a tunnel works until a home router changes its public NAT mapping. Fixed-public-IP assumptions do not hold for frequently changing NAT endpoints.

B:

Configure unique supported peer IDs and matching dial-up or gateway selectors is useful when two branch gateways sit behind one NAT public IP and use overlapping identifiers. Peer identity and connection profiles must disambiguate multiple protected peers.

C:

Enable compatible NAT traversal and confirm UDP 4500 reachability addresses a different symptom: IKE messages cross an intermediate NAT device but ESP traffic fails. NAT-T encapsulates ESP in UDP to work through NAT devices.

Question 533

A FortiGate behind an ISP gateway establishes IPsec with a public peer. An incident review establishes that a peer reports the private source address rather than the public address expected by a fixed-gateway configuration. Which response best fits the observed symptoms?

  1. Enable compatible NAT traversal and confirm UDP 4500 reachability
  2. Check external NAT mapping and the configured peer identification
  3. Permit the required NAT-T UDP 4500 path between gateways
  4. Configure unique supported peer IDs and matching dial-up or gateway selectors

Explanation

Correct Answer

B:

Choose check external NAT mapping and the configured peer identification. Remote gateway expectations must match the reachable translated endpoint and identity. Verify the named control at the affected interface, identity, route, or session boundary.

Incorrect Answers

A:

Enable compatible NAT traversal and confirm UDP 4500 reachability is useful when IKE messages cross an intermediate NAT device but ESP traffic fails. NAT-T encapsulates ESP in UDP to work through NAT devices.

C:

Permit the required NAT-T UDP 4500 path between gateways is relevant when UDP 500 reaches the peer but the intermediate firewall blocks UDP 4500 during NAT detection. IPsec negotiation can transition transport ports when NAT is detected.

D:

Configure unique supported peer IDs and matching dial-up or gateway selectors is useful when two branch gateways sit behind one NAT public IP and use overlapping identifiers. Peer identity and connection profiles must disambiguate multiple protected peers.

Question 534

A FortiGate behind an ISP gateway establishes IPsec with a public peer. The administrator observes that two branch gateways sit behind one NAT public IP and use overlapping identifiers. Which action best meets the stated requirement?

  1. Enable compatible NAT traversal and confirm UDP 4500 reachability
  2. Use a supported dynamic-peer design and validate keepalive behavior
  3. Check external NAT mapping and the configured peer identification
  4. Configure unique supported peer IDs and matching dial-up or gateway selectors

Explanation

Correct Answer

D:

The appropriate control is to configure unique supported peer IDs and matching dial-up or gateway selectors. Peer identity and connection profiles must disambiguate multiple protected peers.

Incorrect Answers

A:

Enable compatible NAT traversal and confirm UDP 4500 reachability addresses a different symptom: IKE messages cross an intermediate NAT device but ESP traffic fails. NAT-T encapsulates ESP in UDP to work through NAT devices.

B:

Use a supported dynamic-peer design and validate keepalive behavior is relevant when a tunnel works until a home router changes its public NAT mapping. Fixed-public-IP assumptions do not hold for frequently changing NAT endpoints.

C:

Check external NAT mapping and the configured peer identification is useful when a peer reports the private source address rather than the public address expected by a fixed-gateway configuration. Remote gateway expectations must match the reachable translated endpoint and identity.

Question 535

A FortiGate behind an ISP gateway establishes IPsec with a public peer. During troubleshooting, the engineer finds that a tunnel works until a home router changes its public NAT mapping. What is the most appropriate next step?

  1. Check external NAT mapping and the configured peer identification
  2. Use a supported dynamic-peer design and validate keepalive behavior
  3. Configure unique supported peer IDs and matching dial-up or gateway selectors
  4. Permit the required NAT-T UDP 4500 path between gateways

Explanation

Correct Answer

B:

Use a supported dynamic-peer design and validate keepalive behavior directly addresses the requirement. Fixed-public-IP assumptions do not hold for frequently changing NAT endpoints.

Incorrect Answers

A:

Check external NAT mapping and the configured peer identification is relevant when a peer reports the private source address rather than the public address expected by a fixed-gateway configuration. Remote gateway expectations must match the reachable translated endpoint and identity.

C:

Configure unique supported peer IDs and matching dial-up or gateway selectors addresses a different symptom: two branch gateways sit behind one NAT public IP and use overlapping identifiers. Peer identity and connection profiles must disambiguate multiple protected peers.

D:

Permit the required NAT-T UDP 4500 path between gateways is relevant when UDP 500 reaches the peer but the intermediate firewall blocks UDP 4500 during NAT detection. IPsec negotiation can transition transport ports when NAT is detected.

Question 536

An IPsec deployment uses pre-shared key authentication and IKE identities. The team reports that the remote peer rejects authentication even though the configured PSK strings match. Which action is most appropriate in this situation?

  1. Verify FQDN/DDNS gateway resolution and the Phase 1 remote gateway definition
  2. Compare IKE local-ID and expected peer-ID settings on both devices
  3. Coordinate the new PSK on both ends during a change window
  4. Use unique strong PSKs and scoped peer definitions for each partner

Explanation

Correct Answer

B:

Compare IKE local-ID and expected peer-ID settings on both devices is the best response. Identity mismatch can fail peer authentication despite a correct key.

Incorrect Answers

A:

Verify FQDN/DDNS gateway resolution and the Phase 1 remote gateway definition is relevant when a tunnel initiator is configured with a wrong remote peer IP but a valid name. Peer reachability depends on resolving and targeting the configured endpoint.

C:

Coordinate the new PSK on both ends during a change window addresses a different symptom: a provider rotates the pre-shared key on one FortiGate only. Both endpoints must use the same authentication secret for the negotiated peer.

D:

Use unique strong PSKs and scoped peer definitions for each partner is relevant when a site uses the same PSK for every unrelated partner tunnel. Separate secrets limit the impact of one exposed tunnel credential.

Question 537

An IPsec deployment uses pre-shared key authentication and IKE identities. In the effective configuration, a provider rotates the pre-shared key on one FortiGate only. What should the administrator do to address the stated condition?

  1. Compare IKE local-ID and expected peer-ID settings on both devices
  2. Use unique strong PSKs and scoped peer definitions for each partner
  3. Coordinate the new PSK on both ends during a change window
  4. Verify FQDN/DDNS gateway resolution and the Phase 1 remote gateway definition

Explanation

Correct Answer

C:

Choose coordinate the new PSK on both ends during a change window. Both endpoints must use the same authentication secret for the negotiated peer.

Incorrect Answers

A:

Compare IKE local-ID and expected peer-ID settings on both devices is useful when the remote peer rejects authentication even though the configured PSK strings match. Identity mismatch can fail peer authentication despite a correct key.

B:

Use unique strong PSKs and scoped peer definitions for each partner addresses a different symptom: a site uses the same PSK for every unrelated partner tunnel. Separate secrets limit the impact of one exposed tunnel credential.

D:

Verify FQDN/DDNS gateway resolution and the Phase 1 remote gateway definition is useful when a tunnel initiator is configured with a wrong remote peer IP but a valid name. Peer reachability depends on resolving and targeting the configured endpoint.

Question 538

An IPsec deployment uses pre-shared key authentication and IKE identities. The current operating problem is that a site uses the same PSK for every unrelated partner tunnel. Which action best meets the stated requirement?

  1. Coordinate the new PSK on both ends during a change window
  2. Compare IKE local-ID and expected peer-ID settings on both devices
  3. Use unique strong PSKs and scoped peer definitions for each partner
  4. Evaluate supported certificate-based IKE peer authentication for that trust requirement

Explanation

Correct Answer

C:

The appropriate control is to use unique strong PSKs and scoped peer definitions for each partner. Separate secrets limit the impact of one exposed tunnel credential.

Incorrect Answers

A:

Coordinate the new PSK on both ends during a change window addresses a different symptom: a provider rotates the pre-shared key on one FortiGate only. Both endpoints must use the same authentication secret for the negotiated peer.

B:

Compare IKE local-ID and expected peer-ID settings on both devices is relevant when the remote peer rejects authentication even though the configured PSK strings match. Identity mismatch can fail peer authentication despite a correct key.

D:

Evaluate supported certificate-based IKE peer authentication for that trust requirement addresses a different symptom: the administrator assumes PSK proves the corporate server identity in a strong third-party trust model. Certificates can bind peers to a verified PKI identity rather than a shared password alone.

Question 539

An IPsec deployment uses pre-shared key authentication and IKE identities. An incident review establishes that a tunnel initiator is configured with a wrong remote peer IP but a valid name. Which next step most directly addresses the reported evidence?

  1. Evaluate supported certificate-based IKE peer authentication for that trust requirement
  2. Compare IKE local-ID and expected peer-ID settings on both devices
  3. Verify FQDN/DDNS gateway resolution and the Phase 1 remote gateway definition
  4. Use unique strong PSKs and scoped peer definitions for each partner

Explanation

Correct Answer

C:

Verify FQDN/DDNS gateway resolution and the Phase 1 remote gateway definition directly addresses the requirement. Peer reachability depends on resolving and targeting the configured endpoint.

Incorrect Answers

A:

Evaluate supported certificate-based IKE peer authentication for that trust requirement is relevant when the administrator assumes PSK proves the corporate server identity in a strong third-party trust model. Certificates can bind peers to a verified PKI identity rather than a shared password alone.

B:

Compare IKE local-ID and expected peer-ID settings on both devices is useful when the remote peer rejects authentication even though the configured PSK strings match. Identity mismatch can fail peer authentication despite a correct key.

D:

Use unique strong PSKs and scoped peer definitions for each partner is relevant when a site uses the same PSK for every unrelated partner tunnel. Separate secrets limit the impact of one exposed tunnel credential.

Question 540

An IPsec deployment uses pre-shared key authentication and IKE identities. The administrator observes that the administrator assumes PSK proves the corporate server identity in a strong third-party trust model. What should the engineer investigate or verify?

  1. Coordinate the new PSK on both ends during a change window
  2. Use unique strong PSKs and scoped peer definitions for each partner
  3. Evaluate supported certificate-based IKE peer authentication for that trust requirement
  4. Verify FQDN/DDNS gateway resolution and the Phase 1 remote gateway definition

Explanation

Correct Answer

C:

Evaluate supported certificate-based IKE peer authentication for that trust requirement is the best response. Certificates can bind peers to a verified PKI identity rather than a shared password alone.

Incorrect Answers

A:

Coordinate the new PSK on both ends during a change window is useful when a provider rotates the pre-shared key on one FortiGate only. Both endpoints must use the same authentication secret for the negotiated peer.

B:

Use unique strong PSKs and scoped peer definitions for each partner addresses a different symptom: a site uses the same PSK for every unrelated partner tunnel. Separate secrets limit the impact of one exposed tunnel credential.

D:

Verify FQDN/DDNS gateway resolution and the Phase 1 remote gateway definition is useful when a tunnel initiator is configured with a wrong remote peer IP but a valid name. Peer reachability depends on resolving and targeting the configured endpoint.

Fortinet NSE 4 - FortiOS 7.6 Administrator (NSE4_FGT_AD-7.6) Practice Tests