mcAfee Secure Website
exam =5
exam =6

Exam Code: NSE4_FGT_AD-7.6

Exam Name: Fortinet NSE 4 - FortiOS 7.6 Administrator

Certification Provider: Fortinet

Corresponding Certification: NSE4

Fortinet NSE4_FGT_AD-7.6 Questions & Answers

Reliable & Actual Study Materials for NSE4_FGT_AD-7.6 Exam Success

94 Questions & Answers with Testing Engine

"NSE4_FGT_AD-7.6: Fortinet NSE 4 - FortiOS 7.6 Administrator" Testing Engine covers all the knowledge points of the real Fortinet NSE4_FGT_AD-7.6 exam.

The latest actual NSE4_FGT_AD-7.6 Questions & Answers from Pass4sure. Everything you need to prepare and get best score at NSE4_FGT_AD-7.6 exam easily and quickly.

exam =7
Guarantee

Satisfaction Guaranteed

Pass4sure has a remarkable Fortinet Candidate Success record. We're confident of our products and provide no hassle product exchange. That's how confident we are!

99.3% Pass Rate
Was: $137.49
Now: $124.99

Fortinet NSE4_FGT_AD-7.6 Practice Test 53

Question 520

Two offices create a new route-based IPsec site-to-site tunnel. The team reports that IKE reaches the remote gateway but the response fails source-interface validation. Which response is most effective for this case?

  1. Select the correct Phase 1 local WAN interface and peer source addressing
  2. Set a mutually supported IKE version on both ends
  3. Configure matching IKE authentication secrets for the expected peer identities
  4. Correct the Phase 1 remote-gateway destination to the actual peer endpoint

Explanation

Correct Answer

A:

Select the correct Phase 1 local WAN interface and peer source addressing is the best response. The tunnel must negotiate using the interface and source address expected by the remote peer.

Incorrect Answers

B:

Set a mutually supported IKE version on both ends is useful when one peer expects IKEv2 but the remote end is explicitly configured for an incompatible IKE version. Both devices must negotiate the same IKE protocol family to establish security associations.

C:

Configure matching IKE authentication secrets for the expected peer identities addresses a different symptom: the two devices agree on algorithms but have different pre-shared keys. Pre-shared key authentication requires the intended shared secret on both ends.

D:

Correct the Phase 1 remote-gateway destination to the actual peer endpoint is relevant when the remote peer gateway address is wrong although both firewalls are reachable generally. IKE is initiated to the configured remote gateway rather than any reachable firewall.

Question 521

A network engineer configures IPsec Phase 2 between two FortiGates. An incident review establishes that phase 1 comes up but Phase 2 cannot establish because local and remote subnet selectors disagree. Which action best meets the stated requirement?

  1. Match the reciprocal Phase 2 traffic selectors to the intended protected prefixes
  2. Configure matching Phase 2 perfect-forward-secrecy settings and DH groups
  3. Extend matching Phase 2 selectors on each peer only for the approved subnet
  4. Inspect Phase 2 lifetimes and rekey negotiation on both ends

Explanation

Correct Answer

A:

Choose match the reciprocal Phase 2 traffic selectors to the intended protected prefixes. Child SA selectors must be compatible between both tunnel ends. Verify the named control at the affected interface, identity, route, or session boundary.

Incorrect Answers

B:

Configure matching Phase 2 perfect-forward-secrecy settings and DH groups is useful when PFS is required by one peer but disabled by the other. PFS negotiation must agree for the child security association.

C:

Extend matching Phase 2 selectors on each peer only for the approved subnet addresses a different symptom: the protected traffic includes a new subnet not covered by the installed selectors. New traffic is not encrypted by an SA whose selectors exclude its addresses.

D:

Inspect Phase 2 lifetimes and rekey negotiation on both ends is relevant when the Phase 2 SA expires and cannot rekey because lifetimes differ unexpectedly. Rekey compatibility and timing affect continuity of established IPsec child SAs.

Question 522

A network engineer configures IPsec Phase 2 between two FortiGates. The administrator observes that phase 2 proposals differ on accepted encryption and integrity settings. What is the most appropriate next step?

  1. Extend matching Phase 2 selectors on each peer only for the approved subnet
  2. Configure matching Phase 2 perfect-forward-secrecy settings and DH groups
  3. Align the supported Phase 2 proposal list on both peers
  4. Match the reciprocal Phase 2 traffic selectors to the intended protected prefixes

Explanation

Correct Answer

C:

The appropriate control is to align the supported Phase 2 proposal list on both peers. ESP SA establishment requires a common Phase 2 cryptographic transform.

Incorrect Answers

A:

Extend matching Phase 2 selectors on each peer only for the approved subnet is useful when the protected traffic includes a new subnet not covered by the installed selectors. New traffic is not encrypted by an SA whose selectors exclude its addresses.

B:

Configure matching Phase 2 perfect-forward-secrecy settings and DH groups addresses a different symptom: PFS is required by one peer but disabled by the other. PFS negotiation must agree for the child security association.

D:

Match the reciprocal Phase 2 traffic selectors to the intended protected prefixes is useful when phase 1 comes up but Phase 2 cannot establish because local and remote subnet selectors disagree. Child SA selectors must be compatible between both tunnel ends.

Question 523

A network engineer configures IPsec Phase 2 between two FortiGates. During troubleshooting, the engineer finds that PFS is required by one peer but disabled by the other. Which control most directly addresses the observed gap?

  1. Configure matching Phase 2 perfect-forward-secrecy settings and DH groups
  2. Align the supported Phase 2 proposal list on both peers
  3. Match the reciprocal Phase 2 traffic selectors to the intended protected prefixes
  4. Inspect Phase 2 lifetimes and rekey negotiation on both ends

Explanation

Correct Answer

A:

Configure matching Phase 2 perfect-forward-secrecy settings and DH groups directly addresses the requirement. PFS negotiation must agree for the child security association.

Incorrect Answers

B:

Align the supported Phase 2 proposal list on both peers is relevant when phase 2 proposals differ on accepted encryption and integrity settings. ESP SA establishment requires a common Phase 2 cryptographic transform.

C:

Match the reciprocal Phase 2 traffic selectors to the intended protected prefixes is useful when phase 1 comes up but Phase 2 cannot establish because local and remote subnet selectors disagree. Child SA selectors must be compatible between both tunnel ends.

D:

Inspect Phase 2 lifetimes and rekey negotiation on both ends addresses a different symptom: the Phase 2 SA expires and cannot rekey because lifetimes differ unexpectedly. Rekey compatibility and timing affect continuity of established IPsec child SAs.

Question 524

A network engineer configures IPsec Phase 2 between two FortiGates. The observed symptom is that the Phase 2 SA expires and cannot rekey because lifetimes differ unexpectedly. Which action is most appropriate in this situation?

  1. Match the reciprocal Phase 2 traffic selectors to the intended protected prefixes
  2. Inspect Phase 2 lifetimes and rekey negotiation on both ends
  3. Configure matching Phase 2 perfect-forward-secrecy settings and DH groups
  4. Align the supported Phase 2 proposal list on both peers

Explanation

Correct Answer

B:

Inspect Phase 2 lifetimes and rekey negotiation on both ends is the best response. Rekey compatibility and timing affect continuity of established IPsec child SAs.

Incorrect Answers

A:

Match the reciprocal Phase 2 traffic selectors to the intended protected prefixes is relevant when phase 1 comes up but Phase 2 cannot establish because local and remote subnet selectors disagree. Child SA selectors must be compatible between both tunnel ends.

C:

Configure matching Phase 2 perfect-forward-secrecy settings and DH groups addresses a different symptom: PFS is required by one peer but disabled by the other. PFS negotiation must agree for the child security association.

D:

Align the supported Phase 2 proposal list on both peers is relevant when phase 2 proposals differ on accepted encryption and integrity settings. ESP SA establishment requires a common Phase 2 cryptographic transform.

Question 525

A network engineer configures IPsec Phase 2 between two FortiGates. A post-change test indicates that the protected traffic includes a new subnet not covered by the installed selectors. What should the administrator do to address the stated condition?

  1. Inspect Phase 2 lifetimes and rekey negotiation on both ends
  2. Configure matching Phase 2 perfect-forward-secrecy settings and DH groups
  3. Extend matching Phase 2 selectors on each peer only for the approved subnet
  4. Match the reciprocal Phase 2 traffic selectors to the intended protected prefixes

Explanation

Correct Answer

C:

Choose extend matching Phase 2 selectors on each peer only for the approved subnet. New traffic is not encrypted by an SA whose selectors exclude its addresses.

Incorrect Answers

A:

Inspect Phase 2 lifetimes and rekey negotiation on both ends is useful when the Phase 2 SA expires and cannot rekey because lifetimes differ unexpectedly. Rekey compatibility and timing affect continuity of established IPsec child SAs.

B:

Configure matching Phase 2 perfect-forward-secrecy settings and DH groups addresses a different symptom: PFS is required by one peer but disabled by the other. PFS negotiation must agree for the child security association.

D:

Match the reciprocal Phase 2 traffic selectors to the intended protected prefixes is useful when phase 1 comes up but Phase 2 cannot establish because local and remote subnet selectors disagree. Child SA selectors must be compatible between both tunnel ends.

Question 526

Two FortiGates establish an IPsec tunnel but business traffic fails. The current operating problem is that IKE and child SAs show established but the local site has no route to remote VLANs. What is the most appropriate next step?

  1. Check remote routing, selectors, remote policies and return path rather than assuming local encryption is broken
  2. Exclude the site-to-site protected traffic from inappropriate source NAT
  3. Add the correct static route through the route-based IPsec interface
  4. Create an appropriate scoped inside-to-IPsec firewall allow policy

Explanation

Correct Answer

C:

The appropriate control is to add the correct static route through the route-based IPsec interface. Tunnel status alone does not direct business packets into the encrypted overlay.

Incorrect Answers

A:

Check remote routing, selectors, remote policies and return path rather than assuming local encryption is broken is useful when phase 2 counters show encrypt bytes increasing but decrypt bytes remain zero. A one-way counter pattern indicates traffic leaves the local tunnel without the expected reply.

B:

Exclude the site-to-site protected traffic from inappropriate source NAT addresses a different symptom: a generic internet SNAT rule matches traffic intended for a selector requiring private source addresses. NAT can change source addresses so they no longer match expected IPsec selectors.

D:

Create an appropriate scoped inside-to-IPsec firewall allow policy is useful when the local route uses the tunnel but firewall forward policy denies the protected traffic. A route-based tunnel still needs security policy authorization for protected packets.

Question 527

Two FortiGates establish an IPsec tunnel but business traffic fails. An incident review establishes that the local route uses the tunnel but firewall forward policy denies the protected traffic. Which control most directly addresses the observed gap?

  1. Check remote routing, selectors, remote policies and return path rather than assuming local encryption is broken
  2. Create an appropriate scoped inside-to-IPsec firewall allow policy
  3. Exclude the site-to-site protected traffic from inappropriate source NAT
  4. Add the correct static route through the route-based IPsec interface

Explanation

Correct Answer

B:

Create an appropriate scoped inside-to-IPsec firewall allow policy directly addresses the requirement. A route-based tunnel still needs security policy authorization for protected packets.

Incorrect Answers

A:

Check remote routing, selectors, remote policies and return path rather than assuming local encryption is broken addresses a different symptom: phase 2 counters show encrypt bytes increasing but decrypt bytes remain zero. A one-way counter pattern indicates traffic leaves the local tunnel without the expected reply.

C:

Exclude the site-to-site protected traffic from inappropriate source NAT is useful when a generic internet SNAT rule matches traffic intended for a selector requiring private source addresses. NAT can change source addresses so they no longer match expected IPsec selectors.

D:

Add the correct static route through the route-based IPsec interface addresses a different symptom: IKE and child SAs show established but the local site has no route to remote VLANs. Tunnel status alone does not direct business packets into the encrypted overlay.

Question 528

Two FortiGates establish an IPsec tunnel but business traffic fails. The administrator observes that remote replies never reach the initiating site because remote return routing is missing. Which response is most effective for this case?

  1. Add the reciprocal remote-side route for the local protected network
  2. Add the correct static route through the route-based IPsec interface
  3. Check remote routing, selectors, remote policies and return path rather than assuming local encryption is broken
  4. Create an appropriate scoped inside-to-IPsec firewall allow policy

Explanation

Correct Answer

A:

Add the reciprocal remote-side route for the local protected network is the best response. A functioning tunnel requires routes in both directions.

Incorrect Answers

B:

Add the correct static route through the route-based IPsec interface is useful when IKE and child SAs show established but the local site has no route to remote VLANs. Tunnel status alone does not direct business packets into the encrypted overlay.

C:

Check remote routing, selectors, remote policies and return path rather than assuming local encryption is broken addresses a different symptom: phase 2 counters show encrypt bytes increasing but decrypt bytes remain zero. A one-way counter pattern indicates traffic leaves the local tunnel without the expected reply.

D:

Create an appropriate scoped inside-to-IPsec firewall allow policy is relevant when the local route uses the tunnel but firewall forward policy denies the protected traffic. A route-based tunnel still needs security policy authorization for protected packets.

Question 529

Two FortiGates establish an IPsec tunnel but business traffic fails. During troubleshooting, the engineer finds that a generic internet SNAT rule matches traffic intended for a selector requiring private source addresses. What should the administrator do to address the stated condition?

  1. Check remote routing, selectors, remote policies and return path rather than assuming local encryption is broken
  2. Create an appropriate scoped inside-to-IPsec firewall allow policy
  3. Add the correct static route through the route-based IPsec interface
  4. Exclude the site-to-site protected traffic from inappropriate source NAT

Explanation

Correct Answer

D:

Choose exclude the site-to-site protected traffic from inappropriate source NAT. NAT can change source addresses so they no longer match expected IPsec selectors. Verify the named control at the affected interface, identity, route, or session boundary.

Incorrect Answers

A:

Check remote routing, selectors, remote policies and return path rather than assuming local encryption is broken is useful when phase 2 counters show encrypt bytes increasing but decrypt bytes remain zero. A one-way counter pattern indicates traffic leaves the local tunnel without the expected reply.

B:

Create an appropriate scoped inside-to-IPsec firewall allow policy addresses a different symptom: the local route uses the tunnel but firewall forward policy denies the protected traffic. A route-based tunnel still needs security policy authorization for protected packets.

C:

Add the correct static route through the route-based IPsec interface is relevant when IKE and child SAs show established but the local site has no route to remote VLANs. Tunnel status alone does not direct business packets into the encrypted overlay.

Question 530

Two FortiGates establish an IPsec tunnel but business traffic fails. The observed symptom is that phase 2 counters show encrypt bytes increasing but decrypt bytes remain zero. Which diagnostic step best resolves the uncertainty?

  1. Check remote routing, selectors, remote policies and return path rather than assuming local encryption is broken
  2. Add the reciprocal remote-side route for the local protected network
  3. Create an appropriate scoped inside-to-IPsec firewall allow policy
  4. Exclude the site-to-site protected traffic from inappropriate source NAT

Explanation

Correct Answer

A:

The appropriate control is to check remote routing, selectors, remote policies and return path rather than assuming local encryption is broken. A one-way counter pattern indicates traffic leaves the local tunnel without the expected reply.

Incorrect Answers

B:

Add the reciprocal remote-side route for the local protected network is relevant when remote replies never reach the initiating site because remote return routing is missing. A functioning tunnel requires routes in both directions.

C:

Create an appropriate scoped inside-to-IPsec firewall allow policy is useful when the local route uses the tunnel but firewall forward policy denies the protected traffic. A route-based tunnel still needs security policy authorization for protected packets.

D:

Exclude the site-to-site protected traffic from inappropriate source NAT addresses a different symptom: a generic internet SNAT rule matches traffic intended for a selector requiring private source addresses. NAT can change source addresses so they no longer match expected IPsec selectors.

Fortinet NSE 4 - FortiOS 7.6 Administrator (NSE4_FGT_AD-7.6) Practice Tests