mcAfee Secure Website
exam =5
exam =6

Exam Code: NSE4_FGT_AD-7.6

Exam Name: Fortinet NSE 4 - FortiOS 7.6 Administrator

Certification Provider: Fortinet

Corresponding Certification: NSE4

Fortinet NSE4_FGT_AD-7.6 Questions & Answers

Reliable & Actual Study Materials for NSE4_FGT_AD-7.6 Exam Success

94 Questions & Answers with Testing Engine

"NSE4_FGT_AD-7.6: Fortinet NSE 4 - FortiOS 7.6 Administrator" Testing Engine covers all the knowledge points of the real Fortinet NSE4_FGT_AD-7.6 exam.

The latest actual NSE4_FGT_AD-7.6 Questions & Answers from Pass4sure. Everything you need to prepare and get best score at NSE4_FGT_AD-7.6 exam easily and quickly.

exam =7
Guarantee

Satisfaction Guaranteed

Pass4sure has a remarkable Fortinet Candidate Success record. We're confident of our products and provide no hassle product exchange. That's how confident we are!

99.3% Pass Rate
Was: $137.49
Now: $124.99

Fortinet NSE4_FGT_AD-7.6 Practice Test 56

Question 550

A branch uses Dead Peer Detection on a route-based IPsec VPN. The current operating problem is that the team tests peer liveness only by pinging an internal server. Which response best fits the observed symptoms?

  1. Check IKE DPD state alongside encrypted application reachability
  2. Inspect DPD and IKE negotiation events separately from static routing
  3. Review DPD timers and retransmission behavior against measured connectivity
  4. Use an appropriate auto-negotiate or keepalive design if an always-ready SA is required

Explanation

Correct Answer

A:

The appropriate control is to check IKE DPD state alongside encrypted application reachability. A remote host's ICMP policy can mislead an otherwise healthy VPN liveness assessment.

Incorrect Answers

B:

Inspect DPD and IKE negotiation events separately from static routing is useful when operators assume a down tunnel implies a missed routing update only. Peer liveness failures and route installation are distinct incident causes.

C:

Review DPD timers and retransmission behavior against measured connectivity addresses a different symptom: DPD triggers constantly during brief planned link jitter and causes unnecessary renegotiation. Overly aggressive peer liveness checks can destabilize a marginal path.

D:

Use an appropriate auto-negotiate or keepalive design if an always-ready SA is required is relevant when a partner VPN has no relevant traffic but on-demand negotiation leaves Phase 2 idle. On-demand SAs may remain inactive until matching protected traffic arrives.

Question 551

An enterprise has two IPsec tunnels over independent WAN circuits. During troubleshooting, the engineer finds that both VPN tunnels route equally but failover should prefer the primary circuit. What is the most appropriate next step?

  1. Set deliberate route preferences and validated backup path health
  2. Match selectors on the backup tunnel to the same approved remote networks
  3. Register both partner-facing peer endpoints and identities on the remote gateway
  4. Combine supported tunnel liveness detection and routing failover behavior

Explanation

Correct Answer

A:

Set deliberate route preferences and validated backup path health directly addresses the requirement. Path selection should reflect the intended active and standby tunnel design.

Incorrect Answers

B:

Match selectors on the backup tunnel to the same approved remote networks is useful when backup tunnel Phase 1 connects but Phase 2 selectors do not include the protected application subnet. A redundant VPN is not useful unless it protects the required application prefixes.

C:

Register both partner-facing peer endpoints and identities on the remote gateway addresses a different symptom: the secondary path uses a different public ISP address that the partner has not permitted. Redundant IPsec paths need consistent configuration at both peers.

D:

Combine supported tunnel liveness detection and routing failover behavior is relevant when the primary tunnel stays installed after the remote gateway becomes unreachable. A static route pointing to a stale VPN path can blackhole traffic.

Question 552

An enterprise has two IPsec tunnels over independent WAN circuits. The observed symptom is that the primary tunnel stays installed after the remote gateway becomes unreachable. Which control most directly addresses the observed gap?

  1. Register both partner-facing peer endpoints and identities on the remote gateway
  2. Match selectors on the backup tunnel to the same approved remote networks
  3. Combine supported tunnel liveness detection and routing failover behavior
  4. Set deliberate route preferences and validated backup path health

Explanation

Correct Answer

C:

Combine supported tunnel liveness detection and routing failover behavior is the best response. A static route pointing to a stale VPN path can blackhole traffic.

Incorrect Answers

A:

Register both partner-facing peer endpoints and identities on the remote gateway is useful when the secondary path uses a different public ISP address that the partner has not permitted. Redundant IPsec paths need consistent configuration at both peers.

B:

Match selectors on the backup tunnel to the same approved remote networks addresses a different symptom: backup tunnel Phase 1 connects but Phase 2 selectors do not include the protected application subnet. A redundant VPN is not useful unless it protects the required application prefixes.

D:

Set deliberate route preferences and validated backup path health is useful when both VPN tunnels route equally but failover should prefer the primary circuit. Path selection should reflect the intended active and standby tunnel design.

Question 553

An enterprise has two IPsec tunnels over independent WAN circuits. A post-change test indicates that backup tunnel Phase 1 connects but Phase 2 selectors do not include the protected application subnet. Which response is most effective for this case?

  1. Register both partner-facing peer endpoints and identities on the remote gateway
  2. Combine supported tunnel liveness detection and routing failover behavior
  3. Test session continuity and application reconnection across the tunnel switch
  4. Match selectors on the backup tunnel to the same approved remote networks

Explanation

Correct Answer

D:

Choose match selectors on the backup tunnel to the same approved remote networks. A redundant VPN is not useful unless it protects the required application prefixes.

Incorrect Answers

A:

Register both partner-facing peer endpoints and identities on the remote gateway addresses a different symptom: the secondary path uses a different public ISP address that the partner has not permitted. Redundant IPsec paths need consistent configuration at both peers.

B:

Combine supported tunnel liveness detection and routing failover behavior is relevant when the primary tunnel stays installed after the remote gateway becomes unreachable. A static route pointing to a stale VPN path can blackhole traffic.

C:

Test session continuity and application reconnection across the tunnel switch is useful when an outage test succeeds for new sessions but breaks existing voice calls on failover. IKE and routing failover do not guarantee seamless preservation of every stateful flow.

Question 554

An enterprise has two IPsec tunnels over independent WAN circuits. The team reports that the secondary path uses a different public ISP address that the partner has not permitted. What should the administrator do to address the stated condition?

  1. Match selectors on the backup tunnel to the same approved remote networks
  2. Register both partner-facing peer endpoints and identities on the remote gateway
  3. Combine supported tunnel liveness detection and routing failover behavior
  4. Set deliberate route preferences and validated backup path health

Explanation

Correct Answer

B:

The appropriate control is to register both partner-facing peer endpoints and identities on the remote gateway. Redundant IPsec paths need consistent configuration at both peers.

Incorrect Answers

A:

Match selectors on the backup tunnel to the same approved remote networks is relevant when backup tunnel Phase 1 connects but Phase 2 selectors do not include the protected application subnet. A redundant VPN is not useful unless it protects the required application prefixes.

C:

Combine supported tunnel liveness detection and routing failover behavior addresses a different symptom: the primary tunnel stays installed after the remote gateway becomes unreachable. A static route pointing to a stale VPN path can blackhole traffic.

D:

Set deliberate route preferences and validated backup path health is relevant when both VPN tunnels route equally but failover should prefer the primary circuit. Path selection should reflect the intended active and standby tunnel design.

Question 555

An enterprise has two IPsec tunnels over independent WAN circuits. In the effective configuration, an outage test succeeds for new sessions but breaks existing voice calls on failover. Which diagnostic step best resolves the uncertainty?

  1. Set deliberate route preferences and validated backup path health
  2. Combine supported tunnel liveness detection and routing failover behavior
  3. Test session continuity and application reconnection across the tunnel switch
  4. Match selectors on the backup tunnel to the same approved remote networks

Explanation

Correct Answer

C:

Test session continuity and application reconnection across the tunnel switch directly addresses the requirement. IKE and routing failover do not guarantee seamless preservation of every stateful flow.

Incorrect Answers

A:

Set deliberate route preferences and validated backup path health is useful when both VPN tunnels route equally but failover should prefer the primary circuit. Path selection should reflect the intended active and standby tunnel design.

B:

Combine supported tunnel liveness detection and routing failover behavior addresses a different symptom: the primary tunnel stays installed after the remote gateway becomes unreachable. A static route pointing to a stale VPN path can blackhole traffic.

D:

Match selectors on the backup tunnel to the same approved remote networks is useful when backup tunnel Phase 1 connects but Phase 2 selectors do not include the protected application subnet. A redundant VPN is not useful unless it protects the required application prefixes.

Question 556

A regional enterprise designs hub-and-spoke IPsec connectivity. The administrator observes that every branch has separate tunnels to every other branch although policy calls for central inspection. Which control most directly addresses the observed gap?

  1. Compare full-mesh and partial-mesh topology to actual application requirements
  2. Introduce an approved subnet renumbering or translation design for the conflict
  3. Add explicit inter-tunnel firewall policies for approved spoke-to-spoke services
  4. Use a hub-and-spoke route-based IPsec topology with controlled spoke-to-spoke forwarding

Explanation

Correct Answer

D:

Use a hub-and-spoke route-based IPsec topology with controlled spoke-to-spoke forwarding is the best response. Hub routing centralizes inspection and reduces unnecessary full-mesh tunnels.

Incorrect Answers

A:

Compare full-mesh and partial-mesh topology to actual application requirements is useful when a complete mesh is chosen for ten branches without estimating operational overhead. Tunnel and routing complexity rises with unnecessary pairwise connections.

B:

Introduce an approved subnet renumbering or translation design for the conflict addresses a different symptom: a branch's source address overlaps another branch's private network. Overlapping private prefixes prevent unambiguous routing without addressing changes.

C:

Add explicit inter-tunnel firewall policies for approved spoke-to-spoke services is relevant when the hub has routes but the firewall blocks traffic between two protected overlay interfaces. Route-based VPN forwarding is still subject to FortiGate security policies.

Question 557

A regional enterprise designs hub-and-spoke IPsec connectivity. During troubleshooting, the engineer finds that spoke A sends branch traffic to the hub but the hub has no route toward Spoke B. Which response is most effective for this case?

  1. Add the correct hub routing path between the spoke tunnel interfaces
  2. Use a hub-and-spoke route-based IPsec topology with controlled spoke-to-spoke forwarding
  3. Introduce an approved subnet renumbering or translation design for the conflict
  4. Add explicit inter-tunnel firewall policies for approved spoke-to-spoke services

Explanation

Correct Answer

A:

Choose add the correct hub routing path between the spoke tunnel interfaces. The hub needs forwarding knowledge for traffic crossing between spokes. Verify the named control at the affected interface, identity, route, or session boundary.

Incorrect Answers

B:

Use a hub-and-spoke route-based IPsec topology with controlled spoke-to-spoke forwarding is relevant when every branch has separate tunnels to every other branch although policy calls for central inspection. Hub routing centralizes inspection and reduces unnecessary full-mesh tunnels.

C:

Introduce an approved subnet renumbering or translation design for the conflict is useful when a branch's source address overlaps another branch's private network. Overlapping private prefixes prevent unambiguous routing without addressing changes.

D:

Add explicit inter-tunnel firewall policies for approved spoke-to-spoke services addresses a different symptom: the hub has routes but the firewall blocks traffic between two protected overlay interfaces. Route-based VPN forwarding is still subject to FortiGate security policies.

Question 558

A regional enterprise designs hub-and-spoke IPsec connectivity. The observed symptom is that the hub has routes but the firewall blocks traffic between two protected overlay interfaces. What should the administrator do to address the stated condition?

  1. Add explicit inter-tunnel firewall policies for approved spoke-to-spoke services
  2. Introduce an approved subnet renumbering or translation design for the conflict
  3. Compare full-mesh and partial-mesh topology to actual application requirements
  4. Add the correct hub routing path between the spoke tunnel interfaces

Explanation

Correct Answer

A:

The appropriate control is to add explicit inter-tunnel firewall policies for approved spoke-to-spoke services. Route-based VPN forwarding is still subject to FortiGate security policies.

Incorrect Answers

B:

Introduce an approved subnet renumbering or translation design for the conflict is useful when a branch's source address overlaps another branch's private network. Overlapping private prefixes prevent unambiguous routing without addressing changes.

C:

Compare full-mesh and partial-mesh topology to actual application requirements addresses a different symptom: a complete mesh is chosen for ten branches without estimating operational overhead. Tunnel and routing complexity rises with unnecessary pairwise connections.

D:

Add the correct hub routing path between the spoke tunnel interfaces is relevant when spoke A sends branch traffic to the hub but the hub has no route toward Spoke B. The hub needs forwarding knowledge for traffic crossing between spokes.

Question 559

A regional enterprise designs hub-and-spoke IPsec connectivity. A post-change test indicates that a branch's source address overlaps another branch's private network. Which action best meets the stated requirement?

  1. Add explicit inter-tunnel firewall policies for approved spoke-to-spoke services
  2. Introduce an approved subnet renumbering or translation design for the conflict
  3. Use a hub-and-spoke route-based IPsec topology with controlled spoke-to-spoke forwarding
  4. Compare full-mesh and partial-mesh topology to actual application requirements

Explanation

Correct Answer

B:

Introduce an approved subnet renumbering or translation design for the conflict directly addresses the requirement. Overlapping private prefixes prevent unambiguous routing without addressing changes.

Incorrect Answers

A:

Add explicit inter-tunnel firewall policies for approved spoke-to-spoke services is useful when the hub has routes but the firewall blocks traffic between two protected overlay interfaces. Route-based VPN forwarding is still subject to FortiGate security policies.

C:

Use a hub-and-spoke route-based IPsec topology with controlled spoke-to-spoke forwarding is relevant when every branch has separate tunnels to every other branch although policy calls for central inspection. Hub routing centralizes inspection and reduces unnecessary full-mesh tunnels.

D:

Compare full-mesh and partial-mesh topology to actual application requirements is useful when a complete mesh is chosen for ten branches without estimating operational overhead. Tunnel and routing complexity rises with unnecessary pairwise connections.

Question 560

A regional enterprise designs hub-and-spoke IPsec connectivity. The team reports that a complete mesh is chosen for ten branches without estimating operational overhead. Which next step most directly addresses the reported evidence?

  1. Add explicit inter-tunnel firewall policies for approved spoke-to-spoke services
  2. Add the correct hub routing path between the spoke tunnel interfaces
  3. Compare full-mesh and partial-mesh topology to actual application requirements
  4. Introduce an approved subnet renumbering or translation design for the conflict

Explanation

Correct Answer

C:

Compare full-mesh and partial-mesh topology to actual application requirements is the best response. Tunnel and routing complexity rises with unnecessary pairwise connections.

Incorrect Answers

A:

Add explicit inter-tunnel firewall policies for approved spoke-to-spoke services addresses a different symptom: the hub has routes but the firewall blocks traffic between two protected overlay interfaces. Route-based VPN forwarding is still subject to FortiGate security policies.

B:

Add the correct hub routing path between the spoke tunnel interfaces is relevant when spoke A sends branch traffic to the hub but the hub has no route toward Spoke B. The hub needs forwarding knowledge for traffic crossing between spokes.

D:

Introduce an approved subnet renumbering or translation design for the conflict addresses a different symptom: a branch's source address overlaps another branch's private network. Overlapping private prefixes prevent unambiguous routing without addressing changes.

Fortinet NSE 4 - FortiOS 7.6 Administrator (NSE4_FGT_AD-7.6) Practice Tests