mcAfee Secure Website
exam =5
exam =6

Exam Code: NSE4_FGT_AD-7.6

Exam Name: Fortinet NSE 4 - FortiOS 7.6 Administrator

Certification Provider: Fortinet

Corresponding Certification: NSE4

Fortinet NSE4_FGT_AD-7.6 Questions & Answers

Reliable & Actual Study Materials for NSE4_FGT_AD-7.6 Exam Success

94 Questions & Answers with Testing Engine

"NSE4_FGT_AD-7.6: Fortinet NSE 4 - FortiOS 7.6 Administrator" Testing Engine covers all the knowledge points of the real Fortinet NSE4_FGT_AD-7.6 exam.

The latest actual NSE4_FGT_AD-7.6 Questions & Answers from Pass4sure. Everything you need to prepare and get best score at NSE4_FGT_AD-7.6 exam easily and quickly.

exam =7
Guarantee

Satisfaction Guaranteed

Pass4sure has a remarkable Fortinet Candidate Success record. We're confident of our products and provide no hassle product exchange. That's how confident we are!

99.3% Pass Rate
Was: $137.49
Now: $124.99

Fortinet NSE4_FGT_AD-7.6 Practice Test 58

Question 570

An engineer inspects IKE negotiation logs for a failing VPN. The observed symptom is that the operator enables broad IKE debug on a busy firewall and floods the console. Which response is most effective for this case?

  1. Filter IKE debug to the target peer and disable it after a bounded capture
  2. Check child proposal, PFS and selector compatibility in Phase 2 diagnostics
  3. Verify UDP 500/4500 arrival at the appropriate WAN interface
  4. Compare configured IKE cryptographic proposals and DH groups

Explanation

Correct Answer

A:

The appropriate control is to filter IKE debug to the target peer and disable it after a bounded capture. Focused negotiation tracing avoids excessive diagnostic overhead and noise.

Incorrect Answers

B:

Check child proposal, PFS and selector compatibility in Phase 2 diagnostics addresses a different symptom: IKE Phase 1 is established but no matching Phase 2 child SA appears. Child-SA requirements are independent from an established IKE SA.

C:

Verify UDP 500/4500 arrival at the appropriate WAN interface is relevant when the firewall has no IKE logs during a connection attempt from an external peer. An IKE negotiation cannot begin if the control traffic never reaches FortiGate.

D:

Compare configured IKE cryptographic proposals and DH groups is useful when IKE Phase 1 fails before authentication and logs no common proposal. Encryption and DH negotiation mismatches prevent IKE SA formation.

Question 571

A FortiGate IPsec tunnel has Phase 2 errors after adding a new application subnet. In the effective configuration, the remote subnet is missing from the local Phase 2 selectors. Which action best meets the stated requirement?

  1. Update the route's VPN interface for the intended protected network
  2. Add the intended destination prefix to compatible Phase 2 selectors on each peer
  3. Create a scoped LAN-to-tunnel accept rule with appropriate return policy
  4. Set compatible ESP encryption and integrity parameters on both peers

Explanation

Correct Answer

B:

Add the intended destination prefix to compatible Phase 2 selectors on each peer directly addresses the requirement. Traffic outside established selectors cannot use the child SA.

Incorrect Answers

A:

Update the route's VPN interface for the intended protected network is useful when a local route points to a retired IPsec tunnel rather than the new one. Forwarding depends on the installed route and tunnel binding.

C:

Create a scoped LAN-to-tunnel accept rule with appropriate return policy is relevant when a firewall has no policy allowing traffic from its inside VLAN to the new VPN interface. VPN child SA does not replace normal firewall access authorization.

D:

Set compatible ESP encryption and integrity parameters on both peers is useful when phase 2 encryption proposals disagree while IKE Phase 1 remains up. Phase 1 success does not prove the child-SA proposal is acceptable.

Question 572

A FortiGate IPsec tunnel has Phase 2 errors after adding a new application subnet. The current operating problem is that one peer configures PFS group 14 while the other only accepts a different group. What is the most appropriate next step?

  1. Align a mutually accepted PFS DH group for the child SA
  2. Set compatible ESP encryption and integrity parameters on both peers
  3. Create a scoped LAN-to-tunnel accept rule with appropriate return policy
  4. Update the route's VPN interface for the intended protected network

Explanation

Correct Answer

A:

Align a mutually accepted PFS DH group for the child SA is the best response. PFS group negotiation must agree at both ends.

Incorrect Answers

B:

Set compatible ESP encryption and integrity parameters on both peers is relevant when phase 2 encryption proposals disagree while IKE Phase 1 remains up. Phase 1 success does not prove the child-SA proposal is acceptable.

C:

Create a scoped LAN-to-tunnel accept rule with appropriate return policy is useful when a firewall has no policy allowing traffic from its inside VLAN to the new VPN interface. VPN child SA does not replace normal firewall access authorization.

D:

Update the route's VPN interface for the intended protected network addresses a different symptom: a local route points to a retired IPsec tunnel rather than the new one. Forwarding depends on the installed route and tunnel binding.

Question 573

A FortiGate IPsec tunnel has Phase 2 errors after adding a new application subnet. An incident review establishes that phase 2 encryption proposals disagree while IKE Phase 1 remains up. Which control most directly addresses the observed gap?

  1. Update the route's VPN interface for the intended protected network
  2. Set compatible ESP encryption and integrity parameters on both peers
  3. Align a mutually accepted PFS DH group for the child SA
  4. Create a scoped LAN-to-tunnel accept rule with appropriate return policy

Explanation

Correct Answer

B:

Choose set compatible ESP encryption and integrity parameters on both peers. Phase 1 success does not prove the child-SA proposal is acceptable. Verify the named control at the affected interface, identity, route, or session boundary.

Incorrect Answers

A:

Update the route's VPN interface for the intended protected network is relevant when a local route points to a retired IPsec tunnel rather than the new one. Forwarding depends on the installed route and tunnel binding.

C:

Align a mutually accepted PFS DH group for the child SA addresses a different symptom: one peer configures PFS group 14 while the other only accepts a different group. PFS group negotiation must agree at both ends.

D:

Create a scoped LAN-to-tunnel accept rule with appropriate return policy is relevant when a firewall has no policy allowing traffic from its inside VLAN to the new VPN interface. VPN child SA does not replace normal firewall access authorization.

Question 574

A FortiGate IPsec tunnel has Phase 2 errors after adding a new application subnet. The administrator observes that a local route points to a retired IPsec tunnel rather than the new one. Which response is most effective for this case?

  1. Set compatible ESP encryption and integrity parameters on both peers
  2. Update the route's VPN interface for the intended protected network
  3. Align a mutually accepted PFS DH group for the child SA
  4. Add the intended destination prefix to compatible Phase 2 selectors on each peer

Explanation

Correct Answer

B:

The appropriate control is to update the route's VPN interface for the intended protected network. Forwarding depends on the installed route and tunnel binding.

Incorrect Answers

A:

Set compatible ESP encryption and integrity parameters on both peers is useful when phase 2 encryption proposals disagree while IKE Phase 1 remains up. Phase 1 success does not prove the child-SA proposal is acceptable.

C:

Align a mutually accepted PFS DH group for the child SA is relevant when one peer configures PFS group 14 while the other only accepts a different group. PFS group negotiation must agree at both ends.

D:

Add the intended destination prefix to compatible Phase 2 selectors on each peer is useful when the remote subnet is missing from the local Phase 2 selectors. Traffic outside established selectors cannot use the child SA.

Question 575

A FortiGate IPsec tunnel has Phase 2 errors after adding a new application subnet. During troubleshooting, the engineer finds that a firewall has no policy allowing traffic from its inside VLAN to the new VPN interface. What should the administrator do to address the stated condition?

  1. Create a scoped LAN-to-tunnel accept rule with appropriate return policy
  2. Align a mutually accepted PFS DH group for the child SA
  3. Update the route's VPN interface for the intended protected network
  4. Add the intended destination prefix to compatible Phase 2 selectors on each peer

Explanation

Correct Answer

A:

Create a scoped LAN-to-tunnel accept rule with appropriate return policy directly addresses the requirement. VPN child SA does not replace normal firewall access authorization.

Incorrect Answers

B:

Align a mutually accepted PFS DH group for the child SA is relevant when one peer configures PFS group 14 while the other only accepts a different group. PFS group negotiation must agree at both ends.

C:

Update the route's VPN interface for the intended protected network is useful when a local route points to a retired IPsec tunnel rather than the new one. Forwarding depends on the installed route and tunnel binding.

D:

Add the intended destination prefix to compatible Phase 2 selectors on each peer addresses a different symptom: the remote subnet is missing from the local Phase 2 selectors. Traffic outside established selectors cannot use the child SA.

Question 576

A security operations center correlates VPN packet captures and debug logs. The team reports that traffic reaches the IPsec WAN port but IKE packets are denied upstream. Which next step most directly addresses the reported evidence?

  1. Compare effective SA lifetimes and DPD/rekey settings on both ends
  2. Inspect matching policy, routes and Phase 2 selector coverage
  3. Capture UDP 500/4500 on the local interface and verify upstream filtering
  4. Verify remote decrypt counters and reverse policies/routes

Explanation

Correct Answer

C:

Capture UDP 500/4500 on the local interface and verify upstream filtering is the best response. IKE and NAT-T control-plane reachability is necessary before negotiation.

Incorrect Answers

A:

Compare effective SA lifetimes and DPD/rekey settings on both ends addresses a different symptom: negotiation repeatedly rekeys on a short interval during low activity. Frequent renegotiation can reflect mismatched timers or unstable peer state.

B:

Inspect matching policy, routes and Phase 2 selector coverage is relevant when IKE up events are present but ESP packet counters never increment on user access. An established SA may remain idle if protected traffic is routed elsewhere or denied.

D:

Verify remote decrypt counters and reverse policies/routes addresses a different symptom: encrypt counters grow but the peer's return traffic never appears. A one-direction flow usually implicates remote forwarding or reply selection.

Question 577

A security operations center correlates VPN packet captures and debug logs. In the effective configuration, IKE up events are present but ESP packet counters never increment on user access. What should the engineer investigate or verify?

  1. Inspect matching policy, routes and Phase 2 selector coverage
  2. Capture UDP 500/4500 on the local interface and verify upstream filtering
  3. Correlate tunnel, firewall policy and UTM log stages for the packet
  4. Verify remote decrypt counters and reverse policies/routes

Explanation

Correct Answer

A:

Choose inspect matching policy, routes and Phase 2 selector coverage. An established SA may remain idle if protected traffic is routed elsewhere or denied.

Incorrect Answers

B:

Capture UDP 500/4500 on the local interface and verify upstream filtering is useful when traffic reaches the IPsec WAN port but IKE packets are denied upstream. IKE and NAT-T control-plane reachability is necessary before negotiation.

C:

Correlate tunnel, firewall policy and UTM log stages for the packet addresses a different symptom: a VPN denial is blamed on FortiGuard web filtering without any web-filter evidence. Encryption, forwarding and content inspection can fail at different stages.

D:

Verify remote decrypt counters and reverse policies/routes is relevant when encrypt counters grow but the peer's return traffic never appears. A one-direction flow usually implicates remote forwarding or reply selection.

Question 578

A security operations center correlates VPN packet captures and debug logs. The current operating problem is that encrypt counters grow but the peer's return traffic never appears. Which action is most appropriate in this situation?

  1. Compare effective SA lifetimes and DPD/rekey settings on both ends
  2. Verify remote decrypt counters and reverse policies/routes
  3. Capture UDP 500/4500 on the local interface and verify upstream filtering
  4. Inspect matching policy, routes and Phase 2 selector coverage

Explanation

Correct Answer

B:

The appropriate control is to verify remote decrypt counters and reverse policies/routes. A one-direction flow usually implicates remote forwarding or reply selection.

Incorrect Answers

A:

Compare effective SA lifetimes and DPD/rekey settings on both ends is useful when negotiation repeatedly rekeys on a short interval during low activity. Frequent renegotiation can reflect mismatched timers or unstable peer state.

C:

Capture UDP 500/4500 on the local interface and verify upstream filtering is relevant when traffic reaches the IPsec WAN port but IKE packets are denied upstream. IKE and NAT-T control-plane reachability is necessary before negotiation.

D:

Inspect matching policy, routes and Phase 2 selector coverage is useful when IKE up events are present but ESP packet counters never increment on user access. An established SA may remain idle if protected traffic is routed elsewhere or denied.

Question 579

A security operations center correlates VPN packet captures and debug logs. An incident review establishes that negotiation repeatedly rekeys on a short interval during low activity. Which response best fits the observed symptoms?

  1. Correlate tunnel, firewall policy and UTM log stages for the packet
  2. Compare effective SA lifetimes and DPD/rekey settings on both ends
  3. Inspect matching policy, routes and Phase 2 selector coverage
  4. Verify remote decrypt counters and reverse policies/routes

Explanation

Correct Answer

B:

Compare effective SA lifetimes and DPD/rekey settings on both ends directly addresses the requirement. Frequent renegotiation can reflect mismatched timers or unstable peer state.

Incorrect Answers

A:

Correlate tunnel, firewall policy and UTM log stages for the packet addresses a different symptom: a VPN denial is blamed on FortiGuard web filtering without any web-filter evidence. Encryption, forwarding and content inspection can fail at different stages.

C:

Inspect matching policy, routes and Phase 2 selector coverage is useful when IKE up events are present but ESP packet counters never increment on user access. An established SA may remain idle if protected traffic is routed elsewhere or denied.

D:

Verify remote decrypt counters and reverse policies/routes addresses a different symptom: encrypt counters grow but the peer's return traffic never appears. A one-direction flow usually implicates remote forwarding or reply selection.

Question 580

A security operations center correlates VPN packet captures and debug logs. The administrator observes that a VPN denial is blamed on FortiGuard web filtering without any web-filter evidence. Which diagnostic step best resolves the uncertainty?

  1. Inspect matching policy, routes and Phase 2 selector coverage
  2. Capture UDP 500/4500 on the local interface and verify upstream filtering
  3. Correlate tunnel, firewall policy and UTM log stages for the packet
  4. Verify remote decrypt counters and reverse policies/routes

Explanation

Correct Answer

C:

Correlate tunnel, firewall policy and UTM log stages for the packet is the best response. Encryption, forwarding and content inspection can fail at different stages.

Incorrect Answers

A:

Inspect matching policy, routes and Phase 2 selector coverage is relevant when IKE up events are present but ESP packet counters never increment on user access. An established SA may remain idle if protected traffic is routed elsewhere or denied.

B:

Capture UDP 500/4500 on the local interface and verify upstream filtering is useful when traffic reaches the IPsec WAN port but IKE packets are denied upstream. IKE and NAT-T control-plane reachability is necessary before negotiation.

D:

Verify remote decrypt counters and reverse policies/routes is relevant when encrypt counters grow but the peer's return traffic never appears. A one-direction flow usually implicates remote forwarding or reply selection.

Fortinet NSE 4 - FortiOS 7.6 Administrator (NSE4_FGT_AD-7.6) Practice Tests