mcAfee Secure Website
exam =5
exam =6

Exam Code: 4A0-D01

Exam Name: Nokia Data Center Fabric Fundamentals

Certification Provider: Nokia

Nokia 4A0-D01 Questions & Answers

Reliable & Actual Study Materials for 4A0-D01 Exam Success

61 Questions & Answers with Testing Engine

"4A0-D01: Nokia Data Center Fabric Fundamentals" Testing Engine covers all the knowledge points of the real Nokia 4A0-D01 exam.

The latest actual 4A0-D01 Questions & Answers from Pass4sure. Everything you need to prepare and get best score at 4A0-D01 exam easily and quickly.

exam =7
Guarantee

Satisfaction Guaranteed

Pass4sure has a remarkable Nokia Candidate Success record. We're confident of our products and provide no hassle product exchange. That's how confident we are!

99.3% Pass Rate
Was: $137.49
Now: $124.99

Nokia 4A0-D01 Practice Test 12

Question 110

In the fictional Ridge-2 east pod, a secondary data hall with tenant isolation requirements, the team reports that traffic must route between tenant subnets while maintaining VRF isolation across VTEPs. A peer suggested: "Require destination-VLAN bridge membership at every intermediary hop" That did not solve the constraint. What should be chosen instead?

  1. Require destination-VLAN bridge membership at every intermediary hop.
  2. Use a correctly designed symmetric IRB L3 EVPN routing model.
  3. Remove the IP-VRF and route all tenants in a single default instance.
  4. Use a CLI alias as the inter-subnet forwarding method.

Explanation

Correct Answer

B:

Symmetric IRB uses distributed tenant routing constructs to support inter-subnet traffic over the overlay. The option uses “Use a correctly designed symmetric IRB L3 EVPN routing model” to address “traffic must route between tenant subnets while maintaining VRF isolation across VTEPs”. The result must be observed on the affected component.

Incorrect Answers

A:

“Require destination-VLAN bridge membership at every intermediary hop” targets a different operation from the reported requirement: “traffic must route between tenant subnets while maintaining VRF isolation across VTEPs”. Symmetric IRB uses distributed tenant routing constructs to support inter-subnet traffic over the overlay. Use the appropriate method: Use a correctly designed symmetric IRB L3 EVPN routing model.

C:

“Remove the IP-VRF and route all tenants in a single default instance” targets a different operation from the reported requirement: “traffic must route between tenant subnets while maintaining VRF isolation across VTEPs”. Symmetric IRB uses distributed tenant routing constructs to support inter-subnet traffic over the overlay. Use the appropriate method: Use a correctly designed symmetric IRB L3 EVPN routing model.

D:

“Use a CLI alias as the inter-subnet forwarding method” targets a different operation from the reported requirement: “traffic must route between tenant subnets while maintaining VRF isolation across VTEPs”. Symmetric IRB uses distributed tenant routing constructs to support inter-subnet traffic over the overlay. Use the appropriate method: Use a correctly designed symmetric IRB L3 EVPN routing model.

Question 111

In the fictional Ridge-2 west pod, a secondary data hall with tenant isolation requirements, the team reports that several operators repeatedly use the same long diagnostic command. An unrelated configuration change is being considered. Which focused remediation best addresses the described problem first?

  1. Create a data-plane VXLAN tunnel for terminal convenience.
  2. Reboot the switch after every repeated command.
  3. Create an appropriate CLI alias for the recurring diagnostic command.
  4. Add a BGP community only to shorten the command text.

Explanation

Correct Answer

C:

Aliases improve CLI usability without altering network forwarding semantics. For Ridge-2, confirm the actual outcome: the alias expands to the intended diagnostic action.

Incorrect Answers

A:

“Create a data-plane VXLAN tunnel for terminal convenience” targets a different operation from the reported requirement: “several operators repeatedly use the same long diagnostic command”. Aliases improve CLI usability without altering network forwarding semantics. Use the appropriate method: Create an appropriate CLI alias for the recurring diagnostic command.

B:

“Reboot the switch after every repeated command” targets a different operation from the reported requirement: “several operators repeatedly use the same long diagnostic command”. Aliases improve CLI usability without altering network forwarding semantics. Use the appropriate method: Create an appropriate CLI alias for the recurring diagnostic command.

D:

“Add a BGP community only to shorten the command text” targets a different operation from the reported requirement: “several operators repeatedly use the same long diagnostic command”. Aliases improve CLI usability without altering network forwarding semantics. Use the appropriate method: Create an appropriate CLI alias for the recurring diagnostic command.

Question 112

In the fictional Ridge-2 east pod, a secondary data hall with tenant isolation requirements, the team reports that a script parses configuration output into machine-readable fields. The shift handoff must specify a defensible solution and the observable service outcome. Which recommendation is technically justified?

  1. Read the command history as though it were live device state.
  2. Treat a tabular summary as a stable cross-version JSON schema.
  3. Convert interface IP addresses into spreadsheet row labels.
  4. Request JSON-formatted CLI or API output rather than scrape decorated terminal text.

Explanation

Correct Answer

D:

Structured output avoids brittle assumptions about human-oriented CLI presentation. The option uses “Request JSON-formatted CLI or API output rather than scrape decorated terminal text” to address “a script parses configuration output into machine-readable fields”. The result must be observed on the affected component.

Incorrect Answers

A:

“Read the command history as though it were live device state” targets a different operation from the reported requirement: “a script parses configuration output into machine-readable fields”. Structured output avoids brittle assumptions about human-oriented CLI presentation. Use the appropriate method: Request JSON-formatted CLI or API output rather than scrape decorated terminal text.

B:

“Treat a tabular summary as a stable cross-version JSON schema” targets a different operation from the reported requirement: “a script parses configuration output into machine-readable fields”. Structured output avoids brittle assumptions about human-oriented CLI presentation. Use the appropriate method: Request JSON-formatted CLI or API output rather than scrape decorated terminal text.

C:

“Convert interface IP addresses into spreadsheet row labels” targets a different operation from the reported requirement: “a script parses configuration output into machine-readable fields”. Structured output avoids brittle assumptions about human-oriented CLI presentation. Use the appropriate method: Request JSON-formatted CLI or API output rather than scrape decorated terminal text.

Question 113

In the fictional Summit-4 east pod, a change-freeze exception for a narrow operational fault, the team reports that a fresh switch boots normally but fails to retrieve its startup configuration. A peer suggested: "Disable every management interface to force ZTP to work" That did not solve the constraint. What should be chosen instead?

  1. Check bootstrap networking, DHCP-provided information and referenced server availability.
  2. Disable every management interface to force ZTP to work.
  3. Change live EVPN Type 2 entries before validating bootstrap transport.
  4. Inspect only production tenant MAC-VRF routes.

Explanation

Correct Answer

A:

Bootstrap failure often comes from missing or unreachable provisioning prerequisites. The option uses “Check bootstrap networking, DHCP-provided information and referenced server availability” to address “a fresh switch boots normally but fails to retrieve its startup configuration”. The result must be observed on the affected component.

Incorrect Answers

B:

“Disable every management interface to force ZTP to work” targets a different operation from the reported requirement: “a fresh switch boots normally but fails to retrieve its startup configuration”. Bootstrap failure often comes from missing or unreachable provisioning prerequisites. Use the appropriate method: Check bootstrap networking, DHCP-provided information and referenced server availability.

C:

“Change live EVPN Type 2 entries before validating bootstrap transport” targets a different operation from the reported requirement: “a fresh switch boots normally but fails to retrieve its startup configuration”. Bootstrap failure often comes from missing or unreachable provisioning prerequisites. Use the appropriate method: Check bootstrap networking, DHCP-provided information and referenced server availability.

D:

“Inspect only production tenant MAC-VRF routes” targets a different operation from the reported requirement: “a fresh switch boots normally but fails to retrieve its startup configuration”. Bootstrap failure often comes from missing or unreachable provisioning prerequisites. Use the appropriate method: Check bootstrap networking, DHCP-provided information and referenced server availability.

Question 114

In the fictional Ridge-2 west pod, a secondary data hall with tenant isolation requirements, the team reports that traffic uses a tenant VRF but only the default route table was examined. A peer suggested: "Assume default-instance routes always show tenant decisions" That did not solve the constraint. What should be chosen instead?

  1. Assume default-instance routes always show tenant decisions.
  2. Inspect the forwarding and routing tables inside the actual tenant IP-VRF.
  3. Check an unrelated MAC-VRF as the IPv4 lookup table.
  4. Change the transport MTU without inspecting the tenant route.

Explanation

Correct Answer

B:

VRF-specific forwarding decisions require examining the correct routing instance. For Ridge-2, confirm the actual outcome: the destination is resolved in the intended tenant IP-VRF.

Incorrect Answers

A:

“Assume default-instance routes always show tenant decisions” targets a different operation from the reported requirement: “traffic uses a tenant VRF but only the default route table was examined”. VRF-specific forwarding decisions require examining the correct routing instance. Use the appropriate method: Inspect the forwarding and routing tables inside the actual tenant IP-VRF.

C:

“Check an unrelated MAC-VRF as the IPv4 lookup table” targets a different operation from the reported requirement: “traffic uses a tenant VRF but only the default route table was examined”. VRF-specific forwarding decisions require examining the correct routing instance. Use the appropriate method: Inspect the forwarding and routing tables inside the actual tenant IP-VRF.

D:

“Change the transport MTU without inspecting the tenant route” targets a different operation from the reported requirement: “traffic uses a tenant VRF but only the default route table was examined”. VRF-specific forwarding decisions require examining the correct routing instance. Use the appropriate method: Inspect the forwarding and routing tables inside the actual tenant IP-VRF.

Question 115

In the fictional Harbor-1 east pod, a staged top-of-rack rollout with a bounded maintenance window, the team reports that the monitoring platform is flooded with low-priority diagnostic records. Which engineering action best satisfies this request?

  1. Disable all logging including faults and security events.
  2. Drop BGP adjacencies to reduce syslog volume.
  3. Tune supported logging levels and destinations while retaining important events.
  4. Change tenant VRFs to control severity thresholds.

Explanation

Correct Answer

C:

Severity and destination selection reduce noise without removing necessary fault evidence. The option uses “Tune supported logging levels and destinations while retaining important events” to address “the monitoring platform is flooded with low-priority diagnostic records”. The result must be observed on the affected component.

Incorrect Answers

A:

“Disable all logging including faults and security events” targets a different operation from the reported requirement: “the monitoring platform is flooded with low-priority diagnostic records”. Severity and destination selection reduce noise without removing necessary fault evidence. Use the appropriate method: Tune supported logging levels and destinations while retaining important events.

B:

“Drop BGP adjacencies to reduce syslog volume” targets a different operation from the reported requirement: “the monitoring platform is flooded with low-priority diagnostic records”. Severity and destination selection reduce noise without removing necessary fault evidence. Use the appropriate method: Tune supported logging levels and destinations while retaining important events.

D:

“Change tenant VRFs to control severity thresholds” targets a different operation from the reported requirement: “the monitoring platform is flooded with low-priority diagnostic records”. Severity and destination selection reduce noise without removing necessary fault evidence. Use the appropriate method: Tune supported logging levels and destinations while retaining important events.

Question 116

In the fictional North-10 west pod, a commissioning exercise under the on-call team, the team reports that IPv6 traffic fails while IPv4 routes to the same leaf are healthy. Which engineering action best satisfies this request?

  1. Change an IPv4-only ACL and declare IPv6 restored.
  2. Move the entire tenant into a Layer 2 hub.
  3. Assume healthy IPv4 forwarding proves IPv6 route installation.
  4. Inspect the IPv6 address-family routes and next-hop resolution separately.

Explanation

Correct Answer

D:

The two IP address families have distinct routes and reachability requirements. For North-10, confirm the actual outcome: the IPv6 destination and next hop are installed in the intended route table.

Incorrect Answers

A:

“Change an IPv4-only ACL and declare IPv6 restored” targets a different operation from the reported requirement: “IPv6 traffic fails while IPv4 routes to the same leaf are healthy”. The two IP address families have distinct routes and reachability requirements. Use the appropriate method: Inspect the IPv6 address-family routes and next-hop resolution separately. Before onboarding, test that the intended fabric state exists.

B:

“Move the entire tenant into a Layer 2 hub” targets a different operation from the reported requirement: “IPv6 traffic fails while IPv4 routes to the same leaf are healthy”. The two IP address families have distinct routes and reachability requirements. Use the appropriate method: Inspect the IPv6 address-family routes and next-hop resolution separately. Before onboarding, test that the intended fabric state exists.

C:

“Assume healthy IPv4 forwarding proves IPv6 route installation” targets a different operation from the reported requirement: “IPv6 traffic fails while IPv4 routes to the same leaf are healthy”. The two IP address families have distinct routes and reachability requirements. Use the appropriate method: Inspect the IPv6 address-family routes and next-hop resolution separately. Before onboarding, test that the intended fabric state exists.

Question 117

In the fictional North-10 east pod, a commissioning exercise under the on-call team, the team reports that two engineers are comparing configured state with a pending change. An unrelated configuration change is being considered. Which focused remediation best addresses the described problem first?

  1. Compare the running and candidate views rather than treating them as identical.
  2. Discard the running view and trust only an offline screenshot.
  3. Use an ACL counter as a substitute for configuration comparison.
  4. Assume any staged edit is automatically committed.

Explanation

Correct Answer

A:

Running and candidate configurations represent different phases of an edit transaction. The option uses “Compare the running and candidate views rather than treating them as identical” to address “two engineers are comparing configured state with a pending change”. The result must be observed on the affected component. Before onboarding, test that the intended fabric state exists.

Incorrect Answers

B:

“Discard the running view and trust only an offline screenshot” targets a different operation from the reported requirement: “two engineers are comparing configured state with a pending change”. Running and candidate configurations represent different phases of an edit transaction. Use the appropriate method: Compare the running and candidate views rather than treating them as identical. Before onboarding, test that the intended fabric state exists.

C:

“Use an ACL counter as a substitute for configuration comparison” targets a different operation from the reported requirement: “two engineers are comparing configured state with a pending change”. Running and candidate configurations represent different phases of an edit transaction. Use the appropriate method: Compare the running and candidate views rather than treating them as identical. Before onboarding, test that the intended fabric state exists.

D:

“Assume any staged edit is automatically committed” targets a different operation from the reported requirement: “two engineers are comparing configured state with a pending change”. Running and candidate configurations represent different phases of an edit transaction. Use the appropriate method: Compare the running and candidate views rather than treating them as identical. Before onboarding, test that the intended fabric state exists.

Question 118

In the fictional Canyon-5 east pod, a fabric operations audit prior to tenant onboarding, the team reports that an automation system needs structured streaming device state. A peer suggested: "Infer device counters from route-target strings" That did not solve the constraint. What should be chosen instead?

  1. Infer device counters from route-target strings.
  2. Use a supported gNMI subscription or retrieval interface.
  3. Encode syslog output as a replacement for interface state models.
  4. Run a human terminal screenshot macro as the only telemetry feed.

Explanation

Correct Answer

B:

GNMI provides a model-driven management path for configuration and telemetry. The option uses “Use a supported gNMI subscription or retrieval interface” to address “an automation system needs structured streaming device state”. The result must be observed on the affected component. Before onboarding, test that the intended fabric state exists.

Incorrect Answers

A:

“Infer device counters from route-target strings” targets a different operation from the reported requirement: “an automation system needs structured streaming device state”. GNMI provides a model-driven management path for configuration and telemetry. Use the appropriate method: Use a supported gNMI subscription or retrieval interface. Before onboarding, test that the intended fabric state exists.

C:

“Encode syslog output as a replacement for interface state models” targets a different operation from the reported requirement: “an automation system needs structured streaming device state”. GNMI provides a model-driven management path for configuration and telemetry. Use the appropriate method: Use a supported gNMI subscription or retrieval interface. Before onboarding, test that the intended fabric state exists.

D:

“Run a human terminal screenshot macro as the only telemetry feed” targets a different operation from the reported requirement: “an automation system needs structured streaming device state”. GNMI provides a model-driven management path for configuration and telemetry. Use the appropriate method: Use a supported gNMI subscription or retrieval interface. Before onboarding, test that the intended fabric state exists.

Question 119

In the fictional Ridge-2 east pod, a secondary data hall with tenant isolation requirements, the team reports that a script parses configuration output into machine-readable fields. A peer suggested: "Treat a tabular summary as a stable cross-version JSON schema" That did not solve the constraint. What should be chosen instead?

  1. Read the command history as though it were live device state.
  2. Convert interface IP addresses into spreadsheet row labels.
  3. Request JSON-formatted CLI or API output rather than scrape decorated terminal text.
  4. Treat a tabular summary as a stable cross-version JSON schema.

Explanation

Correct Answer

C:

Structured output avoids brittle assumptions about human-oriented CLI presentation. The option uses “Request JSON-formatted CLI or API output rather than scrape decorated terminal text” to address “a script parses configuration output into machine-readable fields”. The result must be observed on the affected component.

Incorrect Answers

A:

“Read the command history as though it were live device state” targets a different operation from the reported requirement: “a script parses configuration output into machine-readable fields”. Structured output avoids brittle assumptions about human-oriented CLI presentation. Use the appropriate method: Request JSON-formatted CLI or API output rather than scrape decorated terminal text.

B:

“Convert interface IP addresses into spreadsheet row labels” targets a different operation from the reported requirement: “a script parses configuration output into machine-readable fields”. Structured output avoids brittle assumptions about human-oriented CLI presentation. Use the appropriate method: Request JSON-formatted CLI or API output rather than scrape decorated terminal text.

D:

“Treat a tabular summary as a stable cross-version JSON schema” targets a different operation from the reported requirement: “a script parses configuration output into machine-readable fields”. Structured output avoids brittle assumptions about human-oriented CLI presentation. Use the appropriate method: Request JSON-formatted CLI or API output rather than scrape decorated terminal text.

Question 120

In the fictional Harbor-1 west pod, a staged top-of-rack rollout with a bounded maintenance window, the team reports that unexpected packets target the switch control plane and risk exhausting CPU. The planned change is "Use the CPM filter and appropriate control-plane policers." Which post-change observation best validates the intended technical behavior?

  1. Use an unrelated tenant dashboard as proof, without verifying the required control-plane protection condition.
  2. Confirm that a documentation ticket is marked complete, without checking switch state or forwarding behavior.
  3. Check only that the device hostname is listed in the inventory, without examining control-plane protection behavior.
  4. Verify that legitimate control traffic passes within policy while unwanted rates are constrained.

Explanation

Correct Answer

D:

Control-plane filters and policers protect protocol and management processing capacity. The option uses “Verify that legitimate control traffic passes within policy while unwanted rates are constrained” to address “unexpected packets target the switch control plane and risk exhausting CPU”. The acceptance test is: legitimate control traffic passes within policy while unwanted rates are constrained.

Incorrect Answers

A:

“Use an unrelated tenant dashboard as proof, without verifying the required control-plane protection condition” targets a different operation from the reported requirement: “unexpected packets target the switch control plane and risk exhausting CPU”. Control-plane filters and policers protect protocol and management processing capacity. The confirming result is: legitimate control traffic passes within policy while unwanted rates are constrained.

B:

“Confirm that a documentation ticket is marked complete, without checking switch state or forwarding behavior” targets a different operation from the reported requirement: “unexpected packets target the switch control plane and risk exhausting CPU”. Control-plane filters and policers protect protocol and management processing capacity. The confirming result is: legitimate control traffic passes within policy while unwanted rates are constrained.

C:

“Check only that the device hostname is listed in the inventory, without examining control-plane protection behavior” targets a different operation from the reported requirement: “unexpected packets target the switch control plane and risk exhausting CPU”. Control-plane filters and policers protect protocol and management processing capacity. The confirming result is: legitimate control traffic passes within policy while unwanted rates are constrained.

Nokia Data Center Fabric Fundamentals (4A0-D01) Practice Tests