mcAfee Secure Website
exam =5
exam =6

Exam Code: JN0-481

Exam Name: Data Center, Specialist (JNCIS-DC)

Certification Provider: Juniper

Juniper JN0-481 Questions & Answers

Reliable & Actual Study Materials for JN0-481 Exam Success

65 Questions & Answers with Testing Engine

"JN0-481: Data Center, Specialist (JNCIS-DC)" Testing Engine covers all the knowledge points of the real Juniper JN0-481 exam.

The latest actual JN0-481 Questions & Answers from Pass4sure. Everything you need to prepare and get best score at JN0-481 exam easily and quickly.

exam =7
Guarantee

Satisfaction Guaranteed

Pass4sure has a remarkable Juniper Candidate Success record. We're confident of our products and provide no hassle product exchange. That's how confident we are!

99.3% Pass Rate
Was: $137.49
Now: $124.99

Juniper JN0-481 Practice Test 43

Question 420

A newly installed rack can exchange underlay packets but VTEP loopback routes are missing from the remote leaf routing tables. Which controlled change best addresses the described requirement?

  1. Correct underlay failure detection and routing convergence within the approved topology and timer policy.
  2. Advertise the approved VTEP loopbacks through the fabric underlay and check next-hop reachability.
  3. Repair the routed underlay addressing or protocol configuration and then validate overlay sessions.
  4. Use validated spine-leaf cabling and routing relationships rather than ad hoc lateral transit links.

Explanation

Correct Answer

B:

This action addresses the stated defect: advertise the approved VTEP loopbacks through the fabric underlay and check next-hop reachability. The underlying constraint is that overlay tunnel endpoint reachability depends on the underlay carrying the VTEP loopback routes. Verify rather than assume success: confirm remote VTEP loopbacks resolve to healthy fabric routes and VXLAN tunnel traffic succeeds.

Incorrect Answers

A:

The option “Correct underlay failure detection and routing convergence within the approved topology and timer policy” is useful in a different setting: A fabric uses two equal-cost underlay next hops yet packets continue toward a failed path following a port outage. The case being tested is: A newly installed rack can exchange underlay packets but VTEP loopback routes are missing from the remote leaf routing tables. Advertise the approved VTEP loopbacks through the fabric underlay and check next-hop reachability. The most relevant correction is “Advertise the approved VTEP loopbacks through the fabric underlay and check next-hop reachability”.

C:

That choice—“Repair the routed underlay addressing or protocol configuration and then validate overlay sessions”—addresses this other problem: An additional rack joins a Clos fabric with healthy physical interfaces but fails to form underlay neighbor sessions. Here the scenario is: A newly installed rack can exchange underlay packets but VTEP loopback routes are missing from the remote leaf routing tables. Advertise the approved VTEP loopbacks through the fabric underlay and check next-hop reachability. The most relevant correction is “Advertise the approved VTEP loopbacks through the fabric underlay and check next-hop reachability”.

D:

“Use validated spine-leaf cabling and routing relationships rather than ad hoc lateral transit links” is associated with a distinct issue: A migration plan connects every rack leaf laterally and treats spine devices as only optional edge routers. By contrast, the actual problem is: A newly installed rack can exchange underlay packets but VTEP loopback routes are missing from the remote leaf routing tables. Advertise the approved VTEP loopbacks through the fabric underlay and check next-hop reachability. The most relevant correction is “Advertise the approved VTEP loopbacks through the fabric underlay and check next-hop reachability”.

Question 421

A design is staged and rendered correctly, but a production switch still uses the previous running configuration. Which shortcut would be most likely to undermine this objective?

  1. Treat the existence of a rendered config file as proof of deployment to every switch.
  2. Assume every configuration view is identical and blindly paste one into the device CLI.
  3. Skip diff review and declare the change complete as soon as the design editor saves it.
  4. Delete the old blueprint and recreate every tenant because one hardware identifier changed.

Explanation

Correct Answer

A:

This is the unsafe shortcut to avoid: treat the existence of a rendered config file as proof of deployment to every switch. It violates the principle that staging and rendering intended configuration are distinct from committing and deploying the active blueprint. An appropriate alternative is to review and commit the approved staged change using the documented deployment process.

Incorrect Answers

B:

The option “Assume every configuration view is identical and blindly paste one into the device CLI” is useful in a different setting: A new Apstra deployment includes baseline settings, platform-specific changes and generated overlay commands that an engineer wants to distinguish. The case being tested is: A design is staged and rendered correctly, but a production switch still uses the previous running configuration. Staging and rendering intended configuration are distinct from committing and deploying the active blueprint. The directly relevant unsafe shortcut is “Treat the existence of a rendered config file as proof of deployment to every switch”.

C:

“Skip diff review and declare the change complete as soon as the design editor saves it” is relevant to a different condition: An Apstra operator wants to distinguish blueprint validation from the actual deployment to managed switches. The stated question instead concerns: A design is staged and rendered correctly, but a production switch still uses the previous running configuration. Staging and rendering intended configuration are distinct from committing and deploying the active blueprint. The directly relevant unsafe shortcut is “Treat the existence of a rendered config file as proof of deployment to every switch”.

D:

That choice—“Delete the old blueprint and recreate every tenant because one hardware identifier changed”—addresses this other problem: A failed managed switch is swapped physically yet Apstra refuses deployment to the replacement inventory device. Here the scenario is: A design is staged and rendered correctly, but a production switch still uses the previous running configuration. Staging and rendering intended configuration are distinct from committing and deploying the active blueprint. The directly relevant unsafe shortcut is “Treat the existence of a rendered config file as proof of deployment to every switch”.

Question 422

An operations team adds a hypervisor pair whose access ports are not modeled in Apstra generic-system inventory. Which controlled change best addresses the described requirement?

  1. Investigate unexpected changes using the appropriate generated-config view and approved override workflow.
  2. Create or update the authorized generic system and its connectivity template within the staged blueprint.
  3. Stage the new rack, assign valid devices and resources, validate, then commit through change control.
  4. Use each blueprint tab for its intended lifecycle step and deploy changes only after authorized review.

Explanation

Correct Answer

B:

This action addresses the stated defect: create or update the authorized generic system and its connectivity template within the staged blueprint. The underlying constraint is that generic systems represent attached external workloads and can be modeled with their interfaces and supported connectivity patterns. Verify rather than assume success: verify both expected server interfaces and VLAN or routing attachments appear in active intent and measured connectivity.

Incorrect Answers

A:

That choice—“Investigate unexpected changes using the appropriate generated-config view and approved override workflow”—addresses this other problem: A network engineer sees differences among the pristine, incremental and rendered configurations for a managed leaf. Here the scenario is: An operations team adds a hypervisor pair whose access ports are not modeled in Apstra generic-system inventory. Create or update the authorized generic system and its connectivity template within the staged blueprint. The most relevant correction is “Create or update the authorized generic system and its connectivity template within the staged blueprint”.

C:

The option “Stage the new rack, assign valid devices and resources, validate, then commit through change control” is useful in a different setting: An organization expands a Clos topology and wants newly created racks to inherit validated patterns and allocations. The case being tested is: An operations team adds a hypervisor pair whose access ports are not modeled in Apstra generic-system inventory. Create or update the authorized generic system and its connectivity template within the staged blueprint. The most relevant correction is “Create or update the authorized generic system and its connectivity template within the staged blueprint”.

D:

“Use each blueprint tab for its intended lifecycle step and deploy changes only after authorized review” is relevant to a different condition: A dashboard reports that all switches are reachable while a recent staged policy change has not been deployed. The stated question instead concerns: An operations team adds a hypervisor pair whose access ports are not modeled in Apstra generic-system inventory. Create or update the authorized generic system and its connectivity template within the staged blueprint. The most relevant correction is “Create or update the authorized generic system and its connectivity template within the staged blueprint”.

Question 423

A managed leaf is physically reachable but its Apstra device agent no longer reports state to the controller. Which controlled change best addresses the described requirement?

  1. Restore the supported device-agent connection and management credentials without bypassing security checks.
  2. Select a supported device and image combination and complete controlled onboarding checks.
  3. Use the documented recovery and reconciliation procedure before attempting broad deployment changes.
  4. Coordinate change ownership and apply role or process controls to prevent conflicting unreviewed commits.

Explanation

Correct Answer

A:

This action addresses the stated defect: restore the supported device-agent connection and management credentials without bypassing security checks. The underlying constraint is that the Apstra server relies on managed device agent connectivity and state collection to maintain an accurate operational model. Verify rather than assume success: confirm the server receives fresh device state and reconciles inventory and blueprint expectations.

Incorrect Answers

B:

That choice—“Select a supported device and image combination and complete controlled onboarding checks”—addresses this other problem: A fabric engineer asks whether a managed switch can simply be added to any blueprint without first validating its NOS and device profile. Here the scenario is: A managed leaf is physically reachable but its Apstra device agent no longer reports state to the controller. Restore the supported device-agent connection and management credentials without bypassing security checks. The most relevant correction is “Restore the supported device-agent connection and management credentials without bypassing security checks”.

C:

“Use the documented recovery and reconciliation procedure before attempting broad deployment changes” is associated with a distinct issue: A Juniper Apstra controller is restored following a failure and some device configurations no longer match its database. By contrast, the actual problem is: A managed leaf is physically reachable but its Apstra device agent no longer reports state to the controller. Restore the supported device-agent connection and management credentials without bypassing security checks. The most relevant correction is “Restore the supported device-agent connection and management credentials without bypassing security checks”.

D:

The option “Coordinate change ownership and apply role or process controls to prevent conflicting unreviewed commits” is useful in a different setting: Two on-call staff attempt to stage modifications for the same fabric without a documented approval process. The case being tested is: A managed leaf is physically reachable but its Apstra device agent no longer reports state to the controller. Restore the supported device-agent connection and management credentials without bypassing security checks. The most relevant correction is “Restore the supported device-agent connection and management credentials without bypassing security checks”.

Question 424

A newly staged fabric reports LLDP neighbor mismatches although physical links are up. Which design or operational principle best explains this behavior?

  1. Cable-map discrepancies should be reconciled before traffic flows through an unvalidated physical fabric.
  2. Per-device deployment and configuration status must be inspected rather than assuming a blueprint commit succeeded uniformly.
  3. Cabling validation compares observed neighbor links against intended device/interface relationships.
  4. Controlled build and deploy phases separate design validation, reviewed staged changes and active device updates.

Explanation

Correct Answer

C:

cabling validation compares observed neighbor links against intended device/interface relationships. Here, a newly staged fabric reports LLDP neighbor mismatches although physical links are up. A useful discriminating check is to compare LLDP-discovered endpoints and physical interface identifiers against the generated cable map.

Incorrect Answers

A:

The option “Cable-map discrepancies should be reconciled before traffic flows through an unvalidated physical fabric” is useful in a different setting: A staging team has different cable-map snapshots from design and observed discovery data. The case being tested is: A newly staged fabric reports LLDP neighbor mismatches although physical links are up. Cabling validation compares observed neighbor links against intended device/interface relationships. The controlling principle is “Cabling validation compares observed neighbor links against intended device/interface relationships”.

B:

“Per-device deployment and configuration status must be inspected rather than assuming a blueprint commit succeeded uniformly” is relevant to a different condition: A new switch reports Ready while its peers remain in a deployment-failed state after committing fabric intent. The stated question instead concerns: A newly staged fabric reports LLDP neighbor mismatches although physical links are up. Cabling validation compares observed neighbor links against intended device/interface relationships. The controlling principle is “Cabling validation compares observed neighbor links against intended device/interface relationships”.

D:

“Controlled build and deploy phases separate design validation, reviewed staged changes and active device updates” is associated with a distinct issue: A team needs to roll out a fabric change safely but its change record mixes staging a modification with committing the active state. By contrast, the actual problem is: A newly staged fabric reports LLDP neighbor mismatches although physical links are up. Cabling validation compares observed neighbor links against intended device/interface relationships. The controlling principle is “Cabling validation compares observed neighbor links against intended device/interface relationships”.

Question 425

An endpoint's remote leaf cannot deliver traffic even though the local access VLAN is assigned correctly because the tunnel endpoint is unreachable. Which evidence most directly verifies the intended network outcome?

  1. Verify same-tenant endpoints communicate and traffic is not delivered to the unrelated tenant VNI.
  2. Observe valid endpoint advertisements with less dependence on unknown-destination flooding for known endpoints.
  3. Measure expected BUM replication only among authorized VTEPs and improved traffic counters.
  4. Confirm encapsulated packets reach the intended VTEP and are decapsulated to the authorized bridge domain.

Explanation

Correct Answer

D:

This directly tests the desired result: confirm encapsulated packets reach the intended VTEP and are decapsulated to the authorized bridge domain. The decisive investigation is to inspect VTEP loopback next-hop resolution, VXLAN encapsulation and underlay reachability. The governing principle is that a VTEP provides VXLAN encapsulation and decapsulation and its IP reachability must exist independently of bridge membership.

Incorrect Answers

A:

“Verify same-tenant endpoints communicate and traffic is not delivered to the unrelated tenant VNI” is associated with a distinct issue: A rack migration assigns the correct switch access VLAN but places the VTEP into another tenant's virtual network identifier. By contrast, the actual problem is: An endpoint's remote leaf cannot deliver traffic even though the local access VLAN is assigned correctly because the tunnel endpoint is unreachable. A VTEP provides VXLAN encapsulation and decapsulation and its IP reachability must exist independently of bridge membership. The direct acceptance evidence is “Confirm encapsulated packets reach the intended VTEP and are decapsulated to the authorized bridge domain”.

B:

The option “Observe valid endpoint advertisements with less dependence on unknown-destination flooding for known endpoints” is useful in a different setting: A team wants scalable MAC learning across the fabric rather than sending every remote MAC advertisement by flood. The case being tested is: An endpoint's remote leaf cannot deliver traffic even though the local access VLAN is assigned correctly because the tunnel endpoint is unreachable. A VTEP provides VXLAN encapsulation and decapsulation and its IP reachability must exist independently of bridge membership. The direct acceptance evidence is “Confirm encapsulated packets reach the intended VTEP and are decapsulated to the authorized bridge domain”.

C:

“Measure expected BUM replication only among authorized VTEPs and improved traffic counters” is relevant to a different condition: An overlay virtual network has the correct VNI but unknown destination traffic continues to flood farther than intended. The stated question instead concerns: An endpoint's remote leaf cannot deliver traffic even though the local access VLAN is assigned correctly because the tunnel endpoint is unreachable. A VTEP provides VXLAN encapsulation and decapsulation and its IP reachability must exist independently of bridge membership. The direct acceptance evidence is “Confirm encapsulated packets reach the intended VTEP and are decapsulated to the authorized bridge domain”.

Question 426

An anycast gateway design uses inconsistent SVI gateway parameters on two participating leafs. Which controlled change best addresses the described requirement?

  1. Implement an authorized distributed gateway design and ensure the overlay advertises the required endpoint or prefix routes.
  2. Align the authorized distributed gateway configuration across participating VTEPs.
  3. Advertise and import the required host or prefix routes according to the approved ERB routing design.
  4. Align approved Ethernet segment and multihoming configuration on the participating leaf devices.

Explanation

Correct Answer

B:

This action addresses the stated defect: align the authorized distributed gateway configuration across participating VTEPs. The underlying constraint is that a distributed anycast gateway needs consistent gateway identity and virtual network association across participating leaf devices. Verify rather than assume success: confirm local first-hop forwarding and cross-rack routing continue consistently through each attached leaf.

Incorrect Answers

A:

That choice—“Implement an authorized distributed gateway design and ensure the overlay advertises the required endpoint or prefix routes”—addresses this other problem: An architect wants gateway functions distributed across tenant leafs in an EVPN-VXLAN fabric. Here the scenario is: An anycast gateway design uses inconsistent SVI gateway parameters on two participating leafs. Align the authorized distributed gateway configuration across participating VTEPs. The most relevant correction is “Align the authorized distributed gateway configuration across participating VTEPs”.

C:

The option “Advertise and import the required host or prefix routes according to the approved ERB routing design” is useful in a different setting: A design review confuses Type 2 MAC-IP advertisements with Type 5 IP prefix advertisements in an ERB fabric. The case being tested is: An anycast gateway design uses inconsistent SVI gateway parameters on two participating leafs. Align the authorized distributed gateway configuration across participating VTEPs. The most relevant correction is “Align the authorized distributed gateway configuration across participating VTEPs”.

D:

“Align approved Ethernet segment and multihoming configuration on the participating leaf devices” is relevant to a different condition: An EVPN multihomed endpoint exhibits unstable forwarding after both attachment leafs advertise the same segment independently. The stated question instead concerns: An anycast gateway design uses inconsistent SVI gateway parameters on two participating leafs. Align the authorized distributed gateway configuration across participating VTEPs. The most relevant correction is “Align the authorized distributed gateway configuration across participating VTEPs”.

Question 427

A multirack tenant needs two segmented application subnets while sharing a common VRF routing domain. Which design or operational principle best explains this behavior?

  1. A virtual network's routed gateway and routing-zone association determine its Layer 3 tenant boundary.
  2. Apstra routing zones and VRFs separate tenant Layer 3 routing contexts, allowing overlapping IP ranges by design.
  3. A routing zone can contain multiple virtual networks that share the intended tenant Layer 3 routing context.
  4. Connectivity templates can describe supported external routing sessions and attach them to the intended routing zone.

Explanation

Correct Answer

C:

a routing zone can contain multiple virtual networks that share the intended tenant Layer 3 routing context. Here, a multirack tenant needs two segmented application subnets while sharing a common VRF routing domain. A useful discriminating check is to inspect virtual-network membership and routing-zone assignments for the application segments.

Incorrect Answers

A:

“A virtual network's routed gateway and routing-zone association determine its Layer 3 tenant boundary” is relevant to a different condition: A newly created virtual network must be attached to a tenant VRF, but application packets route through the default routing instance. The stated question instead concerns: A multirack tenant needs two segmented application subnets while sharing a common VRF routing domain. A routing zone can contain multiple virtual networks that share the intended tenant Layer 3 routing context. The controlling principle is “A routing zone can contain multiple virtual networks that share the intended tenant Layer 3 routing context”.

B:

That choice—“Apstra routing zones and VRFs separate tenant Layer 3 routing contexts, allowing overlapping IP ranges by design”—addresses this other problem: Two tenants require identical subnet ranges in a shared physical fabric while remaining isolated. Here the scenario is: A multirack tenant needs two segmented application subnets while sharing a common VRF routing domain. A routing zone can contain multiple virtual networks that share the intended tenant Layer 3 routing context. The controlling principle is “A routing zone can contain multiple virtual networks that share the intended tenant Layer 3 routing context”.

D:

The option “Connectivity templates can describe supported external routing sessions and attach them to the intended routing zone” is useful in a different setting: A tenant needs a dedicated external BGP peering connection without advertising every other tenant's prefixes. The case being tested is: A multirack tenant needs two segmented application subnets while sharing a common VRF routing domain. A routing zone can contain multiple virtual networks that share the intended tenant Layer 3 routing context. The controlling principle is “A routing zone can contain multiple virtual networks that share the intended tenant Layer 3 routing context”.

Question 428

A team needs to identify whether a failed deployment arose from system automation or an approved human change. Which shortcut would be most likely to undermine this objective?

  1. Infer the responsible user solely from the switch's uptime after the outage.
  2. Give the SOC full controller administrator access instead of exporting necessary event records.
  3. Delete inconvenient deployment log entries to keep the audit record clean.
  4. Suppress missing telemetry warnings because the last displayed value was normal.

Explanation

Correct Answer

C:

This is the unsafe shortcut to avoid: delete inconvenient deployment log entries to keep the audit record clean. It violates the principle that controller event logs and deployment records should be correlated with intent revisions and change approvals. An appropriate alternative is to document the causal change and correct the failed deployment through an auditable workflow.

Incorrect Answers

A:

The option “Infer the responsible user solely from the switch's uptime after the outage” is useful in a different setting: A team investigates whether a blueprint revision was created by automation or by an administrator. The case being tested is: A team needs to identify whether a failed deployment arose from system automation or an approved human change. Controller event logs and deployment records should be correlated with intent revisions and change approvals. The directly relevant unsafe shortcut is “Delete inconvenient deployment log entries to keep the audit record clean”.

B:

“Give the SOC full controller administrator access instead of exporting necessary event records” is relevant to a different condition: A security team needs Apstra events delivered to its central log monitoring platform for long-term investigation. The stated question instead concerns: A team needs to identify whether a failed deployment arose from system automation or an approved human change. Controller event logs and deployment records should be correlated with intent revisions and change approvals. The directly relevant unsafe shortcut is “Delete inconvenient deployment log entries to keep the audit record clean”.

D:

“Suppress missing telemetry warnings because the last displayed value was normal” is associated with a distinct issue: A monitoring dashboard shows a device as green but telemetry timestamps stopped updating 20 minutes earlier. By contrast, the actual problem is: A team needs to identify whether a failed deployment arose from system automation or an approved human change. Controller event logs and deployment records should be correlated with intent revisions and change approvals. The directly relevant unsafe shortcut is “Delete inconvenient deployment log entries to keep the audit record clean”.

Question 429

A fabric sees unexpectedly broad BUM traffic after a new VXLAN virtual network is provisioned. Which initial check would most directly distinguish the likely cause?

  1. Trace effective underlay MTU and path fragmentation or drop counters between the participating VTEPs.
  2. Inspect the VLAN-to-VNI bindings on both local and remote VTEPs and compare the blueprint virtual-network intent.
  3. Inspect VTEP loopback next-hop resolution, VXLAN encapsulation and underlay reachability.
  4. Inspect broadcast, unknown-unicast and multicast handling and participating VTEPs for the affected VNI.

Explanation

Correct Answer

D:

This checks the relevant evidence first: inspect broadcast, unknown-unicast and multicast handling and participating VTEPs for the affected VNI. The underlying concept is that BUM replication behavior and EVPN learning strategy must be scoped to the intended VXLAN membership. After confirming the finding, a controlled remediation is to correct replication or multicast membership and virtual-network attachment within the supported fabric design.

Incorrect Answers

A:

“Trace effective underlay MTU and path fragmentation or drop counters between the participating VTEPs” is associated with a distinct issue: A VXLAN packet encapsulation crosses a routed fabric but is discarded along the path due to frame size. By contrast, the actual problem is: A fabric sees unexpectedly broad BUM traffic after a new VXLAN virtual network is provisioned. The relevant inspection is: Inspect broadcast, unknown-unicast and multicast handling and participating VTEPs for the affected VNI. The most discriminating first check is “Inspect broadcast, unknown-unicast and multicast handling and participating VTEPs for the affected VNI”.

B:

The option “Inspect the VLAN-to-VNI bindings on both local and remote VTEPs and compare the blueprint virtual-network intent” is useful in a different setting: A server's VLAN 210 is accidentally bound to the wrong VXLAN segment on one leaf. The case being tested is: A fabric sees unexpectedly broad BUM traffic after a new VXLAN virtual network is provisioned. The relevant inspection is: Inspect broadcast, unknown-unicast and multicast handling and participating VTEPs for the affected VNI. The most discriminating first check is “Inspect broadcast, unknown-unicast and multicast handling and participating VTEPs for the affected VNI”.

C:

“Inspect VTEP loopback next-hop resolution, VXLAN encapsulation and underlay reachability” is relevant to a different condition: An endpoint's remote leaf cannot deliver traffic even though the local access VLAN is assigned correctly because the tunnel endpoint is unreachable. The stated question instead concerns: A fabric sees unexpectedly broad BUM traffic after a new VXLAN virtual network is provisioned. The relevant inspection is: Inspect broadcast, unknown-unicast and multicast handling and participating VTEPs for the affected VNI. The most discriminating first check is “Inspect broadcast, unknown-unicast and multicast handling and participating VTEPs for the affected VNI”.

Question 430

A built-in analytics probe reports a metric but cannot identify why the value changed after a rack migration. Which shortcut would be most likely to undermine this objective?

  1. Raise the anomaly threshold to infinity because the probe currently selects unrelated devices.
  2. Trigger incidents from a single unvalidated stale sample while discarding the source telemetry.
  3. Disable interface telemetry to suppress alerts caused by rising packet errors.
  4. Treat absence of a service configuration anomaly as proof that every application performance metric is normal.

Explanation

Correct Answer

A:

This is the unsafe shortcut to avoid: raise the anomaly threshold to infinity because the probe currently selects unrelated devices. It violates the principle that an IBA probe's context and graph selector are essential to interpreting its measurements and anomaly scope. An appropriate alternative is to narrow the query and probe stages to the correct blueprint nodes and monitored metrics.

Incorrect Answers

B:

“Trigger incidents from a single unvalidated stale sample while discarding the source telemetry” is associated with a distinct issue: A team wants an analytics alert if interface utilization deviates from baseline while still retaining raw evidence. By contrast, the actual problem is: A built-in analytics probe reports a metric but cannot identify why the value changed after a rack migration. An IBA probe's context and graph selector are essential to interpreting its measurements and anomaly scope. The directly relevant unsafe shortcut is “Raise the anomaly threshold to infinity because the probe currently selects unrelated devices”.

C:

The option “Disable interface telemetry to suppress alerts caused by rising packet errors” is useful in a different setting: An operator wants an early-warning signal when fabric interface errors exceed a defined threshold. The case being tested is: A built-in analytics probe reports a metric but cannot identify why the value changed after a rack migration. An IBA probe's context and graph selector are essential to interpreting its measurements and anomaly scope. The directly relevant unsafe shortcut is “Raise the anomaly threshold to infinity because the probe currently selects unrelated devices”.

D:

“Treat absence of a service configuration anomaly as proof that every application performance metric is normal” is relevant to a different condition: An IBA probe reports intermittent latency spikes but application errors are not visible in basic device health summaries. The stated question instead concerns: A built-in analytics probe reports a metric but cannot identify why the value changed after a rack migration. An IBA probe's context and graph selector are essential to interpreting its measurements and anomaly scope. The directly relevant unsafe shortcut is “Raise the anomaly threshold to infinity because the probe currently selects unrelated devices”.

Data Center, Specialist (JNCIS-DC) (JN0-481) Practice Tests