mcAfee Secure Website
exam =5
exam =6

Exam Code: JN0-481

Exam Name: Data Center, Specialist (JNCIS-DC)

Certification Provider: Juniper

Juniper JN0-481 Questions & Answers

Reliable & Actual Study Materials for JN0-481 Exam Success

65 Questions & Answers with Testing Engine

"JN0-481: Data Center, Specialist (JNCIS-DC)" Testing Engine covers all the knowledge points of the real Juniper JN0-481 exam.

The latest actual JN0-481 Questions & Answers from Pass4sure. Everything you need to prepare and get best score at JN0-481 exam easily and quickly.

exam =7
Guarantee

Satisfaction Guaranteed

Pass4sure has a remarkable Juniper Candidate Success record. We're confident of our products and provide no hassle product exchange. That's how confident we are!

99.3% Pass Rate
Was: $137.49
Now: $124.99

Juniper JN0-481 Practice Test 42

Question 410

An east-west application works without tunneling but drops large payloads after VXLAN overlay migration. Which initial check would most directly distinguish the likely cause?

  1. Inspect broadcast, unknown-unicast and multicast handling and participating VTEPs for the affected VNI.
  2. Trace effective underlay MTU and path fragmentation or drop counters between the participating VTEPs.
  3. Inspect the VLAN-to-VNI bindings on both local and remote VTEPs and compare the blueprint virtual-network intent.
  4. Inspect VTEP loopback next-hop resolution, VXLAN encapsulation and underlay reachability.

Explanation

Correct Answer

B:

This checks the relevant evidence first: trace effective underlay MTU and path fragmentation or drop counters between the participating VTEPs. The underlying concept is that VXLAN adds encapsulation overhead and requires adequate path MTU or effective payload sizing. After confirming the finding, a controlled remediation is to configure sufficient supported underlay MTU along the fabric path or safely adjust payload MTU.

Incorrect Answers

A:

That choice—“Inspect broadcast, unknown-unicast and multicast handling and participating VTEPs for the affected VNI”—addresses this other problem: A fabric sees unexpectedly broad BUM traffic after a new VXLAN virtual network is provisioned. Here the scenario is: An east-west application works without tunneling but drops large payloads after VXLAN overlay migration. Trace effective underlay MTU and path fragmentation or drop counters between the participating VTEPs. The most discriminating first check is “Trace effective underlay MTU and path fragmentation or drop counters between the participating VTEPs”.

C:

The option “Inspect the VLAN-to-VNI bindings on both local and remote VTEPs and compare the blueprint virtual-network intent” is useful in a different setting: A rack migration assigns the correct switch access VLAN but places the VTEP into another tenant's virtual network identifier. The case being tested is: An east-west application works without tunneling but drops large payloads after VXLAN overlay migration. Trace effective underlay MTU and path fragmentation or drop counters between the participating VTEPs. The most discriminating first check is “Trace effective underlay MTU and path fragmentation or drop counters between the participating VTEPs”.

D:

“Inspect VTEP loopback next-hop resolution, VXLAN encapsulation and underlay reachability” is relevant to a different condition: A virtualization cluster is moved to another rack and its EVPN routes exist but the remote VXLAN encapsulation next hop fails. The stated question instead concerns: An east-west application works without tunneling but drops large payloads after VXLAN overlay migration. Trace effective underlay MTU and path fragmentation or drop counters between the participating VTEPs. The most discriminating first check is “Trace effective underlay MTU and path fragmentation or drop counters between the participating VTEPs”.

Question 411

An operator advertises an external IPv4 subnet into an EVPN routing domain for routed reachability. Which evidence most directly verifies the intended network outcome?

  1. Observe valid imported EVPN routes and bidirectional host reachability only within the authorized virtual network.
  2. Confirm the remote VTEP has a correctly imported Type 2 endpoint route and can deliver host traffic.
  3. Observe each VRF learns only the intended tenant routes despite overlapping address space.
  4. Confirm the destination subnet appears as an imported Type 5 route and routes end-to-end in the intended VRF.

Explanation

Correct Answer

D:

This directly tests the desired result: confirm the destination subnet appears as an imported Type 5 route and routes end-to-end in the intended VRF. The decisive investigation is to inspect Type 5 prefix advertisements, route-target import and resolving next hops for the tenant VRF. The governing principle is that EVPN Type 5 IP prefix routes represent routed IP reachability, complementing Type 2 endpoint advertisements.

Incorrect Answers

A:

“Observe valid imported EVPN routes and bidirectional host reachability only within the authorized virtual network” is relevant to a different condition: A server VLAN is created on two racks but remote EVPN routes cannot be imported because their route targets do not align. The stated question instead concerns: An operator advertises an external IPv4 subnet into an EVPN routing domain for routed reachability. EVPN Type 5 IP prefix routes represent routed IP reachability, complementing Type 2 endpoint advertisements. The direct acceptance evidence is “Confirm the destination subnet appears as an imported Type 5 route and routes end-to-end in the intended VRF”.

B:

That choice—“Confirm the remote VTEP has a correctly imported Type 2 endpoint route and can deliver host traffic”—addresses this other problem: A leaf needs to advertise a workload endpoint location to remote EVPN participants across the VXLAN fabric. Here the scenario is: An operator advertises an external IPv4 subnet into an EVPN routing domain for routed reachability. EVPN Type 5 IP prefix routes represent routed IP reachability, complementing Type 2 endpoint advertisements. The direct acceptance evidence is “Confirm the destination subnet appears as an imported Type 5 route and routes end-to-end in the intended VRF”.

C:

“Observe each VRF learns only the intended tenant routes despite overlapping address space” is associated with a distinct issue: A provider deploys two isolated VRFs containing identical IP prefixes in distinct tenant spaces. By contrast, the actual problem is: An operator advertises an external IPv4 subnet into an EVPN routing domain for routed reachability. EVPN Type 5 IP prefix routes represent routed IP reachability, complementing Type 2 endpoint advertisements. The direct acceptance evidence is “Confirm the destination subnet appears as an imported Type 5 route and routes end-to-end in the intended VRF”.

Question 412

A routed external firewall must exchange routes with a border leaf for only one tenant VRF. Which evidence most directly verifies the intended network outcome?

  1. Verify the intended external session and imported/exported prefixes appear only in the proper tenant routing context.
  2. Confirm only approved routes are exchanged and unauthorized prefixes no longer leave the fabric.
  3. Confirm the host receives exactly the intended VLANs and no unrelated tenant traffic.
  4. Confirm both VN endpoints are isolated at Layer 2 but routed according to tenant policy within the VRF.

Explanation

Correct Answer

A:

This directly tests the desired result: verify the intended external session and imported/exported prefixes appear only in the proper tenant routing context. The decisive investigation is to inspect border-leaf interfaces, attached connectivity template and tenant-specific routing policy. The governing principle is that connectivity templates can describe supported external routing sessions and attach them to the intended routing zone.

Incorrect Answers

B:

“Confirm only approved routes are exchanged and unauthorized prefixes no longer leave the fabric” is relevant to a different condition: A route export template applied to a border device advertises all tenant prefixes beyond the data center. The stated question instead concerns: A routed external firewall must exchange routes with a border leaf for only one tenant VRF. Connectivity templates can describe supported external routing sessions and attach them to the intended routing zone. The direct acceptance evidence is “Verify the intended external session and imported/exported prefixes appear only in the proper tenant routing context”.

C:

That choice—“Confirm the host receives exactly the intended VLANs and no unrelated tenant traffic”—addresses this other problem: A hypervisor's trunk must carry two allowed application VLANs while leaving unrelated tenant segments inaccessible. Here the scenario is: A routed external firewall must exchange routes with a border leaf for only one tenant VRF. Connectivity templates can describe supported external routing sessions and attach them to the intended routing zone. The direct acceptance evidence is “Verify the intended external session and imported/exported prefixes appear only in the proper tenant routing context”.

D:

“Confirm both VN endpoints are isolated at Layer 2 but routed according to tenant policy within the VRF” is associated with a distinct issue: A user asks whether a single tenant routing zone can include multiple Layer 2 VNs attached to different racks. By contrast, the actual problem is: A routed external firewall must exchange routes with a border leaf for only one tenant VRF. Connectivity templates can describe supported external routing sessions and attach them to the intended routing zone. The direct acceptance evidence is “Verify the intended external session and imported/exported prefixes appear only in the proper tenant routing context”.

Question 413

Two leaves advertise the same virtual network yet one leaf rejects the other's EVPN MAC routes. Which controlled change best addresses the described requirement?

  1. Correct the intended route target mapping and import policies while preserving tenant isolation.
  2. Assign unique route distinguishing context and appropriate route target import and export policy without leaking tenants.
  3. Repair EVPN endpoint advertisement and import eligibility for the affected virtual network.
  4. Align approved Ethernet segment and multihoming configuration on the participating leaf devices.

Explanation

Correct Answer

A:

This action addresses the stated defect: correct the intended route target mapping and import policies while preserving tenant isolation. The underlying constraint is that matching import and export policy for the intended virtual network governs whether EVPN route distribution creates usable reachability. Verify rather than assume success: observe valid imported EVPN routes and bidirectional host reachability only within the authorized virtual network.

Incorrect Answers

B:

The option “Assign unique route distinguishing context and appropriate route target import and export policy without leaking tenants” is useful in a different setting: Two tenants use overlapping private subnets and the team fears one tenant's routes will be mistaken for the other. The case being tested is: Two leaves advertise the same virtual network yet one leaf rejects the other's EVPN MAC routes. Correct the intended route target mapping and import policies while preserving tenant isolation. The most relevant correction is “Correct the intended route target mapping and import policies while preserving tenant isolation”.

C:

“Repair EVPN endpoint advertisement and import eligibility for the affected virtual network” is relevant to a different condition: A leaf needs to advertise a workload endpoint location to remote EVPN participants across the VXLAN fabric. The stated question instead concerns: Two leaves advertise the same virtual network yet one leaf rejects the other's EVPN MAC routes. Correct the intended route target mapping and import policies while preserving tenant isolation. The most relevant correction is “Correct the intended route target mapping and import policies while preserving tenant isolation”.

D:

That choice—“Align approved Ethernet segment and multihoming configuration on the participating leaf devices”—addresses this other problem: An EVPN multihomed endpoint exhibits unstable forwarding after both attachment leafs advertise the same segment independently. Here the scenario is: Two leaves advertise the same virtual network yet one leaf rejects the other's EVPN MAC routes. Correct the intended route target mapping and import policies while preserving tenant isolation. The most relevant correction is “Correct the intended route target mapping and import policies while preserving tenant isolation”.

Question 414

A switch is reachable over SSH but Apstra cannot assign it to a blueprint because the device agent is not installed correctly. Which initial check would most directly distinguish the likely cause?

  1. Compare hardware identifiers, managed system IDs and blueprint allocation entries for the affected devices.
  2. Review device replacement workflow, old/new system identifiers and required port/profile compatibility.
  3. Inspect the device-agent state, management authentication and discovered system ID before allocation.
  4. Inspect the Staged, Uncommitted and Active states and per-device deployment status.

Explanation

Correct Answer

C:

This checks the relevant evidence first: inspect the device-agent state, management authentication and discovered system ID before allocation. The underlying concept is that Apstra fabric onboarding needs a compatible managed agent and correctly established system identity, not only IP connectivity. After confirming the finding, a controlled remediation is to install or repair the supported agent and associate the correct device identity through approved onboarding.

Incorrect Answers

A:

That choice—“Compare hardware identifiers, managed system IDs and blueprint allocation entries for the affected devices”—addresses this other problem: Two appliances appear as one managed system after inventory import because their identifiers were copied from a template. Here the scenario is: A switch is reachable over SSH but Apstra cannot assign it to a blueprint because the device agent is not installed correctly. The relevant inspection is: Inspect the device-agent state, management authentication and discovered system ID before allocation. The most discriminating first check is “Inspect the device-agent state, management authentication and discovered system ID before allocation”.

B:

“Review device replacement workflow, old/new system identifiers and required port/profile compatibility” is associated with a distinct issue: A failed managed switch is swapped physically yet Apstra refuses deployment to the replacement inventory device. By contrast, the actual problem is: A switch is reachable over SSH but Apstra cannot assign it to a blueprint because the device agent is not installed correctly. The relevant inspection is: Inspect the device-agent state, management authentication and discovered system ID before allocation. The most discriminating first check is “Inspect the device-agent state, management authentication and discovered system ID before allocation”.

D:

“Inspect the Staged, Uncommitted and Active states and per-device deployment status” is relevant to a different condition: A design is staged and rendered correctly, but a production switch still uses the previous running configuration. The stated question instead concerns: A switch is reachable over SSH but Apstra cannot assign it to a blueprint because the device agent is not installed correctly. The relevant inspection is: Inspect the device-agent state, management authentication and discovered system ID before allocation. The most discriminating first check is “Inspect the device-agent state, management authentication and discovered system ID before allocation”.

Question 415

A planned rack addition fails because the spine layer has no compatible free ports at the required link speed. Which evidence most directly verifies the intended network outcome?

  1. Prove free compatible spine ports remain after allocating every forecast uplink.
  2. Confirm each instantiated rack matches its logical leaf/uplink topology and allocated resources.
  3. Demonstrate both host attachments map to intended leafs and a single leaf loss meets recovery objectives.
  4. Validate intended path diversity against the generated cable map and a controlled spine failure test.

Explanation

Correct Answer

A:

This directly tests the desired result: prove free compatible spine ports remain after allocating every forecast uplink. The decisive investigation is to review consumed spine port counts, interface maps and oversubscription projections. The governing principle is that total spine capacity includes available physical ports and supported link-speed and topology constraints.

Incorrect Answers

B:

That choice—“Confirm each instantiated rack matches its logical leaf/uplink topology and allocated resources”—addresses this other problem: A new leaf rack should use a repeatable single-leaf topology but its manually modeled connections differ from existing identical racks. Here the scenario is: A planned rack addition fails because the spine layer has no compatible free ports at the required link speed. Total spine capacity includes available physical ports and supported link-speed and topology constraints. The direct acceptance evidence is “Prove free compatible spine ports remain after allocating every forecast uplink”.

C:

“Demonstrate both host attachments map to intended leafs and a single leaf loss meets recovery objectives” is associated with a distinct issue: A rack designer wants a redundant host attachment pattern for critical appliances. By contrast, the actual problem is: A planned rack addition fails because the spine layer has no compatible free ports at the required link speed. Total spine capacity includes available physical ports and supported link-speed and topology constraints. The direct acceptance evidence is “Prove free compatible spine ports remain after allocating every forecast uplink”.

D:

The option “Validate intended path diversity against the generated cable map and a controlled spine failure test” is useful in a different setting: A data center cabling plan repeats one spine endpoint for all redundant paths from a critical rack. The case being tested is: A planned rack addition fails because the spine layer has no compatible free ports at the required link speed. Total spine capacity includes available physical ports and supported link-speed and topology constraints. The direct acceptance evidence is “Prove free compatible spine ports remain after allocating every forecast uplink”.

Question 416

An Apstra design must deploy 12 racks with uniform leaf roles and uplink constraints. Which controlled change best addresses the described requirement?

  1. Expand spine capacity or rescope rack additions under a supported topology design.
  2. Select a supported redundant leaf rack type and document host LAG or independent paths as appropriate.
  3. Correct the cable plan to use approved physically independent spine paths.
  4. Create or select the approved reusable rack type and instantiate the rack consistently.

Explanation

Correct Answer

D:

This action addresses the stated defect: create or select the approved reusable rack type and instantiate the rack consistently. The underlying constraint is that rack types are reusable logical patterns for leaf topology and attached systems within a blueprint. Verify rather than assume success: confirm each instantiated rack matches its logical leaf/uplink topology and allocated resources.

Incorrect Answers

A:

The option “Expand spine capacity or rescope rack additions under a supported topology design” is useful in a different setting: A new tenant floor requests six leaf uplinks but fabric spines are fully committed to existing racks. The case being tested is: An Apstra design must deploy 12 racks with uniform leaf roles and uplink constraints. Create or select the approved reusable rack type and instantiate the rack consistently. The most relevant correction is “Create or select the approved reusable rack type and instantiate the rack consistently”.

B:

“Select a supported redundant leaf rack type and document host LAG or independent paths as appropriate” is relevant to a different condition: A storage workload requires dual-homed servers but a proposed rack type provides only one access leaf. The stated question instead concerns: An Apstra design must deploy 12 racks with uniform leaf roles and uplink constraints. Create or select the approved reusable rack type and instantiate the rack consistently. The most relevant correction is “Create or select the approved reusable rack type and instantiate the rack consistently”.

C:

That choice—“Correct the cable plan to use approved physically independent spine paths”—addresses this other problem: A data center cabling plan repeats one spine endpoint for all redundant paths from a critical rack. Here the scenario is: An Apstra design must deploy 12 racks with uniform leaf roles and uplink constraints. Create or select the approved reusable rack type and instantiate the rack consistently. The most relevant correction is “Create or select the approved reusable rack type and instantiate the rack consistently”.

Question 417

A data-center interconnect extends selected tenant segments between two sites but one site imports unrelated virtual networks. Which initial check would most directly distinguish the likely cause?

  1. Inspect DCI route targets, participating VN or VRF memberships and cross-site advertisements.
  2. Inspect the proposed external or shared-services routing path, import policy and required security controls.
  3. Compare the host attachment, hypervisor port-group mapping and Apstra VN or connectivity-template assignment.
  4. Inspect the generic-system interface and assigned VN tagging primitives in the relevant connectivity template.

Explanation

Correct Answer

A:

This checks the relevant evidence first: inspect DCI route targets, participating VN or VRF memberships and cross-site advertisements. The underlying concept is that DCI design must coordinate intended virtual-network IDs, routing zones and controlled route distribution between sites. After confirming the finding, a controlled remediation is to apply documented DCI policies for only authorized tenant prefixes and virtual-network reachability.

Incorrect Answers

B:

The option “Inspect the proposed external or shared-services routing path, import policy and required security controls” is useful in a different setting: Two tenants require a controlled shared service, and a proposal suggests importing every route into each tenant VRF. The case being tested is: A data-center interconnect extends selected tenant segments between two sites but one site imports unrelated virtual networks. The relevant inspection is: Inspect DCI route targets, participating VN or VRF memberships and cross-site advertisements. The most discriminating first check is “Inspect DCI route targets, participating VN or VRF memberships and cross-site advertisements”.

C:

“Compare the host attachment, hypervisor port-group mapping and Apstra VN or connectivity-template assignment” is relevant to a different condition: A VMware workload migration succeeds at compute level but its new host port cannot reach the expected tenant virtual network. The stated question instead concerns: A data-center interconnect extends selected tenant segments between two sites but one site imports unrelated virtual networks. The relevant inspection is: Inspect DCI route targets, participating VN or VRF memberships and cross-site advertisements. The most discriminating first check is “Inspect DCI route targets, participating VN or VRF memberships and cross-site advertisements”.

D:

That choice—“Inspect the generic-system interface and assigned VN tagging primitives in the relevant connectivity template”—addresses this other problem: A hypervisor's trunk must carry two allowed application VLANs while leaving unrelated tenant segments inaccessible. Here the scenario is: A data-center interconnect extends selected tenant segments between two sites but one site imports unrelated virtual networks. The relevant inspection is: Inspect DCI route targets, participating VN or VRF memberships and cross-site advertisements. The most discriminating first check is “Inspect DCI route targets, participating VN or VRF memberships and cross-site advertisements”.

Question 418

An architect compares an EVPN control plane with reliance on data-plane flood-and-learn for VXLAN workloads. Which shortcut would be most likely to undermine this objective?

  1. Replace the tenant VLAN ID repeatedly without checking VXLAN endpoint reachability.
  2. Disable the EVPN control plane and assume every remote endpoint is learned optimally from normal TCP traffic.
  3. Treat all VXLAN BUM packets as harmless and expand replication to every VTEP in the data center.
  4. Map every rack's VLAN 210 to an arbitrary shared VNI without checking tenant boundaries.

Explanation

Correct Answer

B:

This is the unsafe shortcut to avoid: disable the EVPN control plane and assume every remote endpoint is learned optimally from normal TCP traffic. It violates the principle that EVPN uses a control-plane route exchange to distribute endpoint reachability while VXLAN carries encapsulated data. An appropriate alternative is to use the supported EVPN control plane and verify route import for the intended virtual network.

Incorrect Answers

A:

That choice—“Replace the tenant VLAN ID repeatedly without checking VXLAN endpoint reachability”—addresses this other problem: A virtualization cluster is moved to another rack and its EVPN routes exist but the remote VXLAN encapsulation next hop fails. Here the scenario is: An architect compares an EVPN control plane with reliance on data-plane flood-and-learn for VXLAN workloads. EVPN uses a control-plane route exchange to distribute endpoint reachability while VXLAN carries encapsulated data. The directly relevant unsafe shortcut is “Disable the EVPN control plane and assume every remote endpoint is learned optimally from normal TCP traffic”.

C:

The option “Treat all VXLAN BUM packets as harmless and expand replication to every VTEP in the data center” is useful in a different setting: An overlay virtual network has the correct VNI but unknown destination traffic continues to flood farther than intended. The case being tested is: An architect compares an EVPN control plane with reliance on data-plane flood-and-learn for VXLAN workloads. EVPN uses a control-plane route exchange to distribute endpoint reachability while VXLAN carries encapsulated data. The directly relevant unsafe shortcut is “Disable the EVPN control plane and assume every remote endpoint is learned optimally from normal TCP traffic”.

D:

“Map every rack's VLAN 210 to an arbitrary shared VNI without checking tenant boundaries” is relevant to a different condition: A server's VLAN 210 is accidentally bound to the wrong VXLAN segment on one leaf. The stated question instead concerns: An architect compares an EVPN control plane with reliance on data-plane flood-and-learn for VXLAN workloads. EVPN uses a control-plane route exchange to distribute endpoint reachability while VXLAN carries encapsulated data. The directly relevant unsafe shortcut is “Disable the EVPN control plane and assume every remote endpoint is learned optimally from normal TCP traffic”.

Question 419

A rack template chooses a logical device with insufficient server ports for its planned generic systems. Which controlled change best addresses the described requirement?

  1. Expand or assign a correctly scoped resource pool without overlapping existing allocations.
  2. Apply consistent approved tags and verify the automation selector matches only the intended objects.
  3. Use validated unique VNI allocations or partition resource pools according to approved boundaries.
  4. Use a compatible logical device and device profile combination with sufficient supported host ports.

Explanation

Correct Answer

D:

This action addresses the stated defect: use a compatible logical device and device profile combination with sufficient supported host ports. The underlying constraint is that logical device definitions represent required interface roles and capacities, independent of hardware SKU details. Verify rather than assume success: validate logical port counts and generated rack connections before building the blueprint.

Incorrect Answers

A:

“Expand or assign a correctly scoped resource pool without overlapping existing allocations” is relevant to a different condition: A new blueprint assigns every VTEP from a resource pool that is too small for the proposed rack count. The stated question instead concerns: A rack template chooses a logical device with insufficient server ports for its planned generic systems. The governing requirement is to use a compatible logical device and device profile combination with sufficient supported host ports. The most relevant correction is “Use a compatible logical device and device profile combination with sufficient supported host ports”.

B:

That choice—“Apply consistent approved tags and verify the automation selector matches only the intended objects”—addresses this other problem: A team needs to group rack devices for maintenance based on operational ownership without renaming every node. Here the scenario is: A rack template chooses a logical device with insufficient server ports for its planned generic systems. The governing requirement is to use a compatible logical device and device profile combination with sufficient supported host ports. The most relevant correction is “Use a compatible logical device and device profile combination with sufficient supported host ports”.

C:

“Use validated unique VNI allocations or partition resource pools according to approved boundaries” is associated with a distinct issue: An expansion accidentally reuses a virtual network identifier assigned to another isolated overlay segment. By contrast, the actual problem is: A rack template chooses a logical device with insufficient server ports for its planned generic systems. The governing requirement is to use a compatible logical device and device profile combination with sufficient supported host ports. The most relevant correction is “Use a compatible logical device and device profile combination with sufficient supported host ports”.

Question 420

A newly installed rack can exchange underlay packets but VTEP loopback routes are missing from the remote leaf routing tables. Which controlled change best addresses the described requirement?

  1. Correct underlay failure detection and routing convergence within the approved topology and timer policy.
  2. Advertise the approved VTEP loopbacks through the fabric underlay and check next-hop reachability.
  3. Repair the routed underlay addressing or protocol configuration and then validate overlay sessions.
  4. Use validated spine-leaf cabling and routing relationships rather than ad hoc lateral transit links.

Explanation

Correct Answer

B:

This action addresses the stated defect: advertise the approved VTEP loopbacks through the fabric underlay and check next-hop reachability. The underlying constraint is that overlay tunnel endpoint reachability depends on the underlay carrying the VTEP loopback routes. Verify rather than assume success: confirm remote VTEP loopbacks resolve to healthy fabric routes and VXLAN tunnel traffic succeeds.

Incorrect Answers

A:

The option “Correct underlay failure detection and routing convergence within the approved topology and timer policy” is useful in a different setting: A fabric uses two equal-cost underlay next hops yet packets continue toward a failed path following a port outage. The case being tested is: A newly installed rack can exchange underlay packets but VTEP loopback routes are missing from the remote leaf routing tables. Advertise the approved VTEP loopbacks through the fabric underlay and check next-hop reachability. The most relevant correction is “Advertise the approved VTEP loopbacks through the fabric underlay and check next-hop reachability”.

C:

That choice—“Repair the routed underlay addressing or protocol configuration and then validate overlay sessions”—addresses this other problem: An additional rack joins a Clos fabric with healthy physical interfaces but fails to form underlay neighbor sessions. Here the scenario is: A newly installed rack can exchange underlay packets but VTEP loopback routes are missing from the remote leaf routing tables. Advertise the approved VTEP loopbacks through the fabric underlay and check next-hop reachability. The most relevant correction is “Advertise the approved VTEP loopbacks through the fabric underlay and check next-hop reachability”.

D:

“Use validated spine-leaf cabling and routing relationships rather than ad hoc lateral transit links” is associated with a distinct issue: A migration plan connects every rack leaf laterally and treats spine devices as only optional edge routers. By contrast, the actual problem is: A newly installed rack can exchange underlay packets but VTEP loopback routes are missing from the remote leaf routing tables. Advertise the approved VTEP loopbacks through the fabric underlay and check next-hop reachability. The most relevant correction is “Advertise the approved VTEP loopbacks through the fabric underlay and check next-hop reachability”.

Data Center, Specialist (JNCIS-DC) (JN0-481) Practice Tests