mcAfee Secure Website
exam =5
exam =6

Exam Code: JN0-364

Exam Name: Service Provider Routing and Switching, Specialist (JNCIS-SP)

Certification Provider: Juniper

Juniper JN0-364 Questions & Answers

Reliable & Actual Study Materials for JN0-364 Exam Success

69 Questions & Answers with Testing Engine

"JN0-364: Service Provider Routing and Switching, Specialist (JNCIS-SP)" Testing Engine covers all the knowledge points of the real Juniper JN0-364 exam.

The latest actual JN0-364 Questions & Answers from Pass4sure. Everything you need to prepare and get best score at JN0-364 exam easily and quickly.

exam =7
Guarantee

Satisfaction Guaranteed

Pass4sure has a remarkable Juniper Candidate Success record. We're confident of our products and provide no hassle product exchange. That's how confident we are!

99.3% Pass Rate
Was: $137.49
Now: $124.99

Juniper JN0-364 Practice Test 78

Question 770

A peer announces an IPv6 prefix but the operator checks only the IPv4 BGP route family. What observable result most directly verifies the intended configuration?

  1. The test confirms that the planned ABR topology provides verified interarea reachability.
  2. Expected observation: The internal router resolves the next hop and installs the intended route.
  3. Verification result: A test prefix reaches permitted clients without cycling through reflector clusters.
  4. Closeout evidence: The intended inet6 family receives and selects the IPv6 prefix.

Explanation

Correct Answer

D:

This option addresses the stated case rather than another networking issue. Principle: BGP transport connectivity does not guarantee every address family is negotiated and active. Remedy: Verify negotiated address families and family-specific routing tables. Proof: The intended inet6 family receives and selects the IPv6 prefix.

Incorrect Answers

A:

Multi-area OSPF design requires attention to backbone connectivity describes a neighboring protocol concern. In this case the controlling fact is bGP transport connectivity does not guarantee every address family is negotiated and active. A correct remediation would verify negotiated address families and family-specific routing tables and demonstrate: The intended inet6 family receives and selects the IPv6 prefix.

B:

The proposed principle concerns another network fault: Unresolvable BGP next hops can make received routes unusable. Here, bGP transport connectivity does not guarantee every address family is negotiated and active. The most direct correction is to verify negotiated address families and family-specific routing tables, confirmed by the intended inet6 family receives and selects the IPv6 prefix.

C:

That result would be useful for a different failure, namely: A route reflector advertises routes to the wrong clients after a change in group membership. The current case specifically calls for: Verify negotiated address families and family-specific routing tables. The required observed result is: The intended inet6 family receives and selects the IPv6 prefix.

Question 771

A VLAN provides local host connectivity but hosts cannot reach a different IP subnet through the bridge domain. Which change best corrects the failure without losing the intended design?

  1. Recommended change: Verify VLAN or bridge-domain membership and its L3 IRB binding.
  2. Next step: Deploy or validate an integrated routing and bridging L3 interface and gateway.
  3. Corrective action: Trace trunk authorization, bridge-domain membership and MAC learning across the path.
  4. Apply this control: Review VRRP virtual router roles, priority and failover behavior.

Explanation

Correct Answer

B:

Underlying cause: Layer 2 bridging does not by itself provide IP intersubnet routing. Corrective action: deploy or validate an integrated routing and bridging L3 interface and gateway. Verify the outcome: A test host reaches its gateway and an authorized remote subnet through IRB.

Incorrect Answers

A:

The alternative addresses an IRB interface is present but an operator assumes it creates a bridge domain automatically, not the present root cause. Here the selected correction must reflect layer 2 bridging does not by itself provide IP intersubnet routing. Test for: A test host reaches its gateway and an authorized remote subnet through IRB.

C:

This option overlooks the decisive condition. Its supporting principle is a working IRB gateway does not validate all L2 paths and trunk members, while this scenario depends on layer 2 bridging does not by itself provide IP intersubnet routing. Verify the correction with: A test host reaches its gateway and an authorized remote subnet through IRB.

D:

VRRP provides a master and backup mechanism for a shared virtual default gateway describes a neighboring protocol concern. In this case the controlling fact is layer 2 bridging does not by itself provide IP intersubnet routing. A correct remediation would deploy or validate an integrated routing and bridging L3 interface and gateway and demonstrate: A test host reaches its gateway and an authorized remote subnet through IRB.

Question 772

Several VLANs have unexpected root placement under VSTP after port membership changes. Which combined repair and acceptance criterion is strongest?

  1. Change: Verify VLAN-to-IRB interface binding, addresses and active route entries. Test: A test host ARPs or discovers its gateway and routes to the intended subnet.
  2. Implement: Evaluate MSTP instances and explicit VLAN-to-instance mapping. Verify: Each VLAN maps to its intended instance and designated root.
  3. Control: Inspect per-VLAN STP instances and configured priorities, not just a global STP summary. Accepted result: Each tested VLAN elects its approved root and loop-free port roles.
  4. Action: Compare root priority, bridge identifiers and current STP topology status. Evidence: A controlled election yields the approved root with documented path changes.

Explanation

Correct Answer

C:

This is the model-intended best choice because per-VLAN spanning-tree behavior can differ across VLANs. The targeted correction is to inspect per-VLAN STP instances and configured priorities, not just a global STP summary. Validate it by observing that each tested VLAN elects its approved root and loop-free port roles.

Incorrect Answers

A:

That result would be useful for a different failure, namely: A router-on-a-stick replacement with IRB stops reachability between a bridge domain and an L3 subnet. The current case specifically calls for: Inspect per-VLAN STP instances and configured priorities, not just a global STP summary. The required observed result is: Each tested VLAN elects its approved root and loop-free port roles.

B:

This response would target a different source scenario: A data center needs separate spanning trees for VLAN groupings but the plan uses a single root for every VLAN with no design review. It cannot establish the current acceptance requirement, which is: Each tested VLAN elects its approved root and loop-free port roles. The relevant action is: Inspect per-VLAN STP instances and configured priorities, not just a global STP summary.

D:

The alternative addresses a planned root bridge migration is configured but the operational root remains on the old switch, not the present root cause. Here the selected correction must reflect per-VLAN spanning-tree behavior can differ across VLANs. Test for: Each tested VLAN elects its approved root and loop-free port roles.

Question 773

An edge port connected to a user device unexpectedly receives BPDUs from an unauthorized switch. Which change best corrects the failure without losing the intended design?

  1. Apply this control: Separate customer bridge domains and validate virtual-switch membership.
  2. Remediation: Inspect spanning-tree loop-protection events, root path and link state.
  3. Recommended change: Apply suitable BPDU protection according to edge-port policy.
  4. Next step: Match loop, BPDU and root protection to their different fault conditions.

Explanation

Correct Answer

C:

Underlying cause: BPDU protection can prevent rogue switching from affecting a designated edge port. Corrective action: apply suitable BPDU protection according to edge-port policy. Verify the outcome: A controlled BPDU causes the expected protected-port response.

Incorrect Answers

A:

This option overlooks the decisive condition. Its supporting principle is layer 2 isolation depends on bridge-domain and logical switch boundaries, while this scenario depends on bPDU protection can prevent rogue switching from affecting a designated edge port. Verify the correction with: A controlled BPDU causes the expected protected-port response.

B:

Loop protection can prevent unsafe forwarding when control-plane information is missing describes a neighboring protocol concern. In this case the controlling fact is bPDU protection can prevent rogue switching from affecting a designated edge port. A correct remediation would apply suitable BPDU protection according to edge-port policy and demonstrate: A controlled BPDU causes the expected protected-port response.

D:

That result would be useful for a different failure, namely: An engineer uses loop protection as if it served the same purpose as BPDU protection on every port. The current case specifically calls for: Apply suitable BPDU protection according to edge-port policy. The required observed result is: A controlled BPDU causes the expected protected-port response.

Question 774

A generated route is configured but its expected contributing route is absent from the routing table. What is the primary routing or switching concept illustrated?

  1. Underlying principle: BGP transport connectivity does not guarantee every address family is negotiated and active.
  2. Root design issue: Address validity and martian filtering affect which route sources are considered acceptable.
  3. The governing rule is: Imported routes must be validated in the destination lookup context.
  4. The key distinction is: A generated route depends on its contributing-route conditions rather than mere configuration presence.

Explanation

Correct Answer

D:

This is the model-intended best choice because a generated route depends on its contributing-route conditions rather than mere configuration presence. The targeted correction is to verify route contribution and the conditions for route generation. Validate it by observing that the generated prefix appears only when the required contributing route is active.

Incorrect Answers

A:

Verify negotiated address families and family-specific routing tables is a relevant step for the separate scenario in which a peer announces an IPv6 prefix but the operator checks only the IPv4 BGP route family. It does not directly fix this case. Instead verify route contribution and the conditions for route generation; verify: The generated prefix appears only when the required contributing route is active.

B:

The alternative addresses an operator accepts a source-address block as an ordinary next-hop network even though the address is classified as martian, not the present root cause. Here the selected correction must reflect a generated route depends on its contributing-route conditions rather than mere configuration presence. Test for: The generated prefix appears only when the required contributing route is active.

C:

This answer would be more suitable when a RIB group leak forwards a VPN service toward the wrong next hop after a route update, where the corrective action is to check import destinations, next-hop resolution and effective routes in every receiving table. The failure here is different: A generated route depends on its contributing-route conditions rather than mere configuration presence. Required validation: The generated prefix appears only when the required contributing route is active.

Question 775

An OSPF trace shows Hellos received but database synchronization stalls at ExStart or Exchange. Which statement identifies the key design assumption that failed?

  1. Protocol behavior: Neighbor discovery can succeed even when database exchange parameters prevent completion.
  2. Underlying principle: Multi-area OSPF design requires attention to backbone connectivity.
  3. Root design issue: External OSPF redistribution must be reviewed for scope and scale.
  4. The governing rule is: A backup path requires functional forwarding, not merely topology presence.

Explanation

Correct Answer

A:

The selected response implements the principle that neighbor discovery can succeed even when database exchange parameters prevent completion. The engineer should check MTU and interface compatibility and inspect neighbor-state details. Successful confirmation means: The adjacency advances through database synchronization to Full.

Incorrect Answers

B:

That result would be useful for a different failure, namely: A router in a nonbackbone area cannot reach a newly connected area through a topology that skips Area 0. The current case specifically calls for: Check MTU and interface compatibility and inspect neighbor-state details. The required observed result is: The adjacency advances through database synchronization to Full.

C:

This response would target a different source scenario: A BGP prefix redistribution into OSPF causes a flood of routes that were not in the approved design. It cannot establish the current acceptance requirement, which is: The adjacency advances through database synchronization to Full. The relevant action is: Check MTU and interface compatibility and inspect neighbor-state details.

D:

Rehearse the failure and inspect active next hops and IS-IS route changes is a relevant step for the separate scenario in which a provider failover exposes an alternate IS-IS path that had never been tested for next-hop resolution. It does not directly fix this case. Instead check MTU and interface compatibility and inspect neighbor-state details; verify: The adjacency advances through database synchronization to Full.

Question 776

An engineer expects an IS-IS Designated Intermediate System election on a point-to-point core link. A reviewer requires a remedy and concrete test evidence. Which pairing fits?

  1. Implement: Place the correct L1/L2 boundary and evaluate flooding scope. Verify: The planned area topology reaches distant prefixes through eligible Level 2 routing.
  2. Control: Restore appropriate IGP next-hop reachability or approved next-hop-self behavior. Accepted result: The internal router resolves the next hop and installs the intended route.
  3. Action: Rehearse the failure and inspect active next hops and IS-IS route changes. Evidence: The backup next hop resolves and carries test traffic after the primary link fails.
  4. Repair: Differentiate multiaccess DIS election from point-to-point adjacency behavior. Check: A point-to-point link reaches the expected adjacency state without DIS election.

Explanation

Correct Answer

D:

Because the IS-IS DIS concept applies to LANs rather than ordinary point-to-point links, the best response is to differentiate multiaccess DIS election from point-to-point adjacency behavior. A reviewer can close the technical case only after confirming that a point-to-point link reaches the expected adjacency state without DIS election.

Incorrect Answers

A:

This answer would be more suitable when a provider uses a Level 1-only router to interconnect two independent IS-IS areas and expects unrestricted cross-area flooding, where the corrective action is to place the correct L1/L2 boundary and evaluate flooding scope. The failure here is different: The IS-IS DIS concept applies to LANs rather than ordinary point-to-point links. Required validation: A point-to-point link reaches the expected adjacency state without DIS election.

B:

This option overlooks the decisive condition. Its supporting principle is unresolvable BGP next hops can make received routes unusable, while this scenario depends on the IS-IS DIS concept applies to LANs rather than ordinary point-to-point links. Verify the correction with: A point-to-point link reaches the expected adjacency state without DIS election.

C:

A backup path requires functional forwarding, not merely topology presence describes a neighboring protocol concern. In this case the controlling fact is the IS-IS DIS concept applies to LANs rather than ordinary point-to-point links. A correct remediation would differentiate multiaccess DIS election from point-to-point adjacency behavior and demonstrate: A point-to-point link reaches the expected adjacency state without DIS election.

Question 777

An engineer wants to filter routing information at an IS-IS boundary but applies a policy to the wrong routing context. Which cause-and-remedy pairing reflects the observed problem?

  1. Explanation: A backup path requires functional forwarding, not merely topology presence. Repair: Rehearse the failure and inspect active next hops and IS-IS route changes.
  2. Fault mechanism: Policy placement determines which prefixes influence a routing table or advertisement. Remediation: Apply and verify supported route policy at the intended routing import or export boundary.
  3. Root issue: Failover paths are governed by their actual configured metrics. Correction: Confirm the explicit cost plan in a failure rehearsal using route and topology outputs.
  4. Cause: An adjacency can be operational while a specific family or prefix is not advertised. Response: Distinguish IS-IS adjacency from address-family reachability advertisements.

Explanation

Correct Answer

B:

The selected response implements the principle that policy placement determines which prefixes influence a routing table or advertisement. The engineer should apply and verify supported route policy at the intended routing import or export boundary. Successful confirmation means: The allowed prefixes are present and denied test prefixes are absent.

Incorrect Answers

A:

This response would target a different source scenario: A provider failover exposes an alternate IS-IS path that had never been tested for next-hop resolution. It cannot establish the current acceptance requirement, which is: The allowed prefixes are present and denied test prefixes are absent. The relevant action is: Apply and verify supported route policy at the intended routing import or export boundary.

C:

The alternative addresses an OSPF route appears longer than expected after failover because a backup link's cost was never verified, not the present root cause. Here the selected correction must reflect policy placement determines which prefixes influence a routing table or advertisement. Test for: The allowed prefixes are present and denied test prefixes are absent.

D:

This answer would be more suitable when a core engineer sees that IPv6 reachability is absent despite IS-IS adjacency and concludes the adjacency itself is broken, where the corrective action is to distinguish IS-IS adjacency from address-family reachability advertisements. The failure here is different: Policy placement determines which prefixes influence a routing table or advertisement. Required validation: The allowed prefixes are present and denied test prefixes are absent.

Question 778

A provider migrates one path from LDP to SR-MPLS but does not verify the segment-routing forwarding state. Which technical distinction best describes the observed symptom?

  1. Root design issue: A healthy transport LSP does not guarantee a correct overlay label mapping.
  2. The governing rule is: Different segment types express different routing or link steering semantics.
  3. The key distinction is: Policy evaluation order can short-circuit later intended acceptance.
  4. Protocol behavior: LDP and SR-MPLS may coexist but each needs its own valid label/route state.

Explanation

Correct Answer

D:

This option addresses the stated case rather than another networking issue. Principle: LDP and SR-MPLS may coexist but each needs its own valid label/route state. Remedy: Check SR label advertisements, segment configuration and installed MPLS forwarding. Proof: The intended SR transport path forwards without unintended dependence on the retired LDP path.

Incorrect Answers

A:

A healthy transport LSP does not guarantee a correct overlay label mapping describes a neighboring protocol concern. In this case the controlling fact is lDP and SR-MPLS may coexist but each needs its own valid label/route state. A correct remediation would check SR label advertisements, segment configuration and installed MPLS forwarding and demonstrate: The intended SR transport path forwards without unintended dependence on the retired LDP path.

B:

The proposed principle concerns another network fault: Different segment types express different routing or link steering semantics. Here, lDP and SR-MPLS may coexist but each needs its own valid label/route state. The most direct correction is to check SR label advertisements, segment configuration and installed MPLS forwarding, confirmed by the intended SR transport path forwards without unintended dependence on the retired LDP path.

C:

That result would be useful for a different failure, namely: A BGP prefix remains rejected after an intended route filter update because an earlier term rejects it. The current case specifically calls for: Check SR label advertisements, segment configuration and installed MPLS forwarding. The required observed result is: The intended SR transport path forwards without unintended dependence on the retired LDP path.

Question 779

An operator assumes OSPFv3 must form using the same interface and address settings as OSPFv2. Which technical distinction best describes the observed symptom?

  1. Underlying principle: A configured IPv6 static route still depends on reachable forwarding next hops.
  2. Root design issue: GRE by itself does not provide encryption or authenticated confidentiality.
  3. The governing rule is: OSPFv3 has protocol-specific requirements for neighbor exchange and IPv6 routing.
  4. The key distinction is: An IPv6 BGP route requires a resolvable eligible next hop for forwarding.

Explanation

Correct Answer

C:

The selected response implements the principle that oSPFv3 has protocol-specific requirements for neighbor exchange and IPv6 routing. The engineer should review the IPv6 OSPFv3 address-family and interface adjacency model. Successful confirmation means: The peers exchange the expected IPv6 routes using a valid OSPFv3 adjacency.

Incorrect Answers

A:

The alternative addresses a router has an IPv6 default route but no usable next-hop reachability on the egress link, not the present root cause. Here the selected correction must reflect oSPFv3 has protocol-specific requirements for neighbor exchange and IPv6 routing. Test for: The peers exchange the expected IPv6 routes using a valid OSPFv3 adjacency.

B:

This answer would be more suitable when a network operator assumes a GRE tunnel encrypts customer packets merely because they are encapsulated, where the corrective action is to distinguish tunneling encapsulation from confidentiality protection. The failure here is different: OSPFv3 has protocol-specific requirements for neighbor exchange and IPv6 routing. Required validation: The peers exchange the expected IPv6 routes using a valid OSPFv3 adjacency.

D:

An IPv6 BGP route requires a resolvable eligible next hop for forwarding describes a neighboring protocol concern. In this case the controlling fact is oSPFv3 has protocol-specific requirements for neighbor exchange and IPv6 routing. A correct remediation would review the IPv6 OSPFv3 address-family and interface adjacency model and demonstrate: The peers exchange the expected IPv6 routes using a valid OSPFv3 adjacency.

Question 780

A routing peer detects a dead neighbor too slowly for a real-time service even when the interface stays up. What implementation step and validation result should be selected?

  1. Control: Check whether GRES is paired with the intended GR or NSR support and verify protocol state. Accepted result: A planned switchover test documents forwarding and neighbor behavior against the HA design.
  2. Action: Evaluate BFD liveness detection with the associated routing protocol. Evidence: A controlled forwarding failure is detected within the approved target.
  3. Repair: Review VRRP virtual router roles, priority and failover behavior. Check: Only the intended master forwards for the virtual gateway under steady state.
  4. Change: Review router priorities and the nonpreemptive properties of DR elections. Test: The elected DR and BDR align with the tested election conditions.

Explanation

Correct Answer

B:

Because bFD provides faster forwarding-path liveness information than ordinary long protocol timers in supported deployments, the best response is to evaluate BFD liveness detection with the associated routing protocol. A reviewer can close the technical case only after confirming that a controlled forwarding failure is detected within the approved target.

Incorrect Answers

A:

That result would be useful for a different failure, namely: A Routing Engine switchover retains data-plane traffic briefly but causes OSPF adjacencies to restart. The current case specifically calls for: Evaluate BFD liveness detection with the associated routing protocol. The required observed result is: A controlled forwarding failure is detected within the approved target.

C:

Review VRRP virtual router roles, priority and failover behavior is a relevant step for the separate scenario in which two edge routers advertise one gateway service and an engineer expects both to be virtual master without a redundancy plan. It does not directly fix this case. Instead evaluate BFD liveness detection with the associated routing protocol; verify: A controlled forwarding failure is detected within the approved target.

D:

The alternative addresses a broadcast OSPF segment experiences repeated DR elections after interface priority changes, not the present root cause. Here the selected correction must reflect bFD provides faster forwarding-path liveness information than ordinary long protocol timers in supported deployments. Test for: A controlled forwarding failure is detected within the approved target.

Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests