mcAfee Secure Website
exam =5
exam =6

Exam Code: JN0-364

Exam Name: Service Provider Routing and Switching, Specialist (JNCIS-SP)

Certification Provider: Juniper

Juniper JN0-364 Questions & Answers

Reliable & Actual Study Materials for JN0-364 Exam Success

69 Questions & Answers with Testing Engine

"JN0-364: Service Provider Routing and Switching, Specialist (JNCIS-SP)" Testing Engine covers all the knowledge points of the real Juniper JN0-364 exam.

The latest actual JN0-364 Questions & Answers from Pass4sure. Everything you need to prepare and get best score at JN0-364 exam easily and quickly.

exam =7
Guarantee

Satisfaction Guaranteed

Pass4sure has a remarkable Juniper Candidate Success record. We're confident of our products and provide no hassle product exchange. That's how confident we are!

99.3% Pass Rate
Was: $137.49
Now: $124.99

Juniper JN0-364 Practice Test 77

Question 760

An engineer assumes both routers must reach Full with every speaker on a broadcast network. What remediation is most directly applicable?

  1. Next step: Separate route-selection and lookup-table changes and test each with candidate configuration.
  2. Corrective action: Coordinate authentication parameters and test the key change under maintenance controls.
  3. Apply this control: Revisit additive path cost and verify SPF outcomes across alternative links.
  4. Remediation: Check the expected DR/BDR versus DROther neighbor-state relationships.

Explanation

Correct Answer

D:

Because oSPF broadcast topology reduces unnecessary full adjacency mesh formation, the best response is to check the expected DR/BDR versus DROther neighbor-state relationships. A reviewer can close the technical case only after confirming that the neighbor states match expected DR roles and routing converges.

Incorrect Answers

A:

This answer would be more suitable when a policy adjustment changes both routing preference and forwarding instance selection in one unreviewed commit, where the corrective action is to separate route-selection and lookup-table changes and test each with candidate configuration. The failure here is different: OSPF broadcast topology reduces unnecessary full adjacency mesh formation. Required validation: The neighbor states match expected DR roles and routing converges.

B:

This option overlooks the decisive condition. Its supporting principle is authentication mismatches can reject otherwise valid OSPF protocol packets, while this scenario depends on oSPF broadcast topology reduces unnecessary full adjacency mesh formation. Verify the correction with: The neighbor states match expected DR roles and routing converges.

C:

OSPF normally prefers the least accumulated metric to a destination describes a neighboring protocol concern. In this case the controlling fact is oSPF broadcast topology reduces unnecessary full adjacency mesh formation. A correct remediation would check the expected DR/BDR versus DROther neighbor-state relationships and demonstrate: The neighbor states match expected DR roles and routing converges.

Question 761

A router has an IPv6 default route but no usable next-hop reachability on the egress link. Which cause-and-remedy pairing reflects the observed problem?

  1. Fault mechanism: A configured IPv6 static route still depends on reachable forwarding next hops. Remediation: Confirm the IPv6 next-hop adjacency and active routing entry.
  2. Root issue: Common topology information can still produce direction-dependent shortest paths. Correction: Compare path metrics and each router's route selection before altering LSP state.
  3. Cause: IS-IS adjacency and IPv6 prefix exchange are separate operational concerns. Response: Enable and verify the intended IPv6 address-family reachability advertisements.
  4. Diagnosis: More-specific routes can override an otherwise healthy IPv6 fallback. Action: Inspect longest-match results and forwarding routes for the specific destination.

Explanation

Correct Answer

A:

Underlying cause: A configured IPv6 static route still depends on reachable forwarding next hops. Corrective action: confirm the IPv6 next-hop adjacency and active routing entry. Verify the outcome: The IPv6 FIB resolves the intended next hop and a test packet crosses the link.

Incorrect Answers

B:

Compare path metrics and each router's route selection before altering LSP state is a relevant step for the separate scenario in which an IS-IS link has asymmetric traffic despite synchronized LSPs and the engineer assumes the LSDB itself is corrupted. It does not directly fix this case. Instead confirm the IPv6 next-hop adjacency and active routing entry; verify: The IPv6 FIB resolves the intended next hop and a test packet crosses the link.

C:

The alternative addresses an IS-IS backbone forms an adjacency but omits IPv6 reachability when the family is not enabled, not the present root cause. Here the selected correction must reflect a configured IPv6 static route still depends on reachable forwarding next hops. Test for: The IPv6 FIB resolves the intended next hop and a test packet crosses the link.

D:

This answer would be more suitable when a new IPv6 static backup route is configured but a more-specific route points into a blackhole, where the corrective action is to inspect longest-match results and forwarding routes for the specific destination. The failure here is different: A configured IPv6 static route still depends on reachable forwarding next hops. Required validation: The IPv6 FIB resolves the intended next hop and a test packet crosses the link.

Question 762

A router-on-a-stick replacement with IRB stops reachability between a bridge domain and an L3 subnet. Which statement identifies the key design assumption that failed?

  1. The governing rule is: Loop protection can prevent unsafe forwarding when control-plane information is missing.
  2. The key distinction is: IRB depends on both L2 membership and a valid L3 gateway configuration.
  3. Protocol behavior: MAC learning reflects observed source location and may churn during loops or mobility.
  4. Underlying principle: MAC table visibility alone does not prove trunk authorization for every VLAN.

Explanation

Correct Answer

B:

This is the model-intended best choice because iRB depends on both L2 membership and a valid L3 gateway configuration. The targeted correction is to verify VLAN-to-IRB interface binding, addresses and active route entries. Validate it by observing that a test host ARPs or discovers its gateway and routes to the intended subnet.

Incorrect Answers

A:

Loop protection can prevent unsafe forwarding when control-plane information is missing describes a neighboring protocol concern. In this case the controlling fact is iRB depends on both L2 membership and a valid L3 gateway configuration. A correct remediation would verify VLAN-to-IRB interface binding, addresses and active route entries and demonstrate: A test host ARPs or discovers its gateway and routes to the intended subnet.

C:

That result would be useful for a different failure, namely: A carrier receives the same source MAC from two access ports and sees frequent forwarding-table moves. The current case specifically calls for: Verify VLAN-to-IRB interface binding, addresses and active route entries. The required observed result is: A test host ARPs or discovers its gateway and routes to the intended subnet.

D:

This response would target a different source scenario: After a trunk change a MAC address is visible but only one of two VLANs can traverse the uplink. It cannot establish the current acceptance requirement, which is: A test host ARPs or discovers its gateway and routes to the intended subnet. The relevant action is: Verify VLAN-to-IRB interface binding, addresses and active route entries.

Question 763

OSPF route preference changes after a new link is added and a latency-sensitive service takes the wrong path. Which statement identifies the key design assumption that failed?

  1. Root design issue: OSPF normally prefers the least accumulated metric to a destination.
  2. The governing rule is: OSPF forwarding decisions depend on cumulative metric, not interface bandwidth labels alone.
  3. The key distinction is: IS-IS packet exchange and transport differ from OSPF over IP.
  4. Protocol behavior: Interarea reachability depends on the ABR's view and allowed advertisements.

Explanation

Correct Answer

B:

Underlying cause: OSPF forwarding decisions depend on cumulative metric, not interface bandwidth labels alone. Corrective action: review each interface's OSPF metric and compare end-to-end computed costs. Verify the outcome: A post-change route view selects the approved shortest path.

Incorrect Answers

A:

The alternative addresses a branch uses a higher OSPF interface cost but expects that branch to remain the preferred primary path, not the present root cause. Here the selected correction must reflect oSPF forwarding decisions depend on cumulative metric, not interface bandwidth labels alone. Test for: A post-change route view selects the approved shortest path.

C:

This option overlooks the decisive condition. Its supporting principle is iS-IS packet exchange and transport differ from OSPF over IP, while this scenario depends on oSPF forwarding decisions depend on cumulative metric, not interface bandwidth labels alone. Verify the correction with: A post-change route view selects the approved shortest path.

D:

Interarea reachability depends on the ABR's view and allowed advertisements describes a neighboring protocol concern. In this case the controlling fact is oSPF forwarding decisions depend on cumulative metric, not interface bandwidth labels alone. A correct remediation would review each interface's OSPF metric and compare end-to-end computed costs and demonstrate: A post-change route view selects the approved shortest path.

Question 764

A provider uses a Level 1-only router to interconnect two independent IS-IS areas and expects unrestricted cross-area flooding. Which underlying Junos networking principle explains the failure?

  1. Underlying principle: An adjacency can be operational while a specific family or prefix is not advertised.
  2. Root design issue: BGP group inheritance and policy direction govern which advertisements are modified.
  3. The governing rule is: A backup path requires functional forwarding, not merely topology presence.
  4. The key distinction is: IS-IS route dissemination follows hierarchical level boundaries.

Explanation

Correct Answer

D:

Correct diagnosis: IS-IS route dissemination follows hierarchical level boundaries. The appropriate action is: Place the correct L1/L2 boundary and evaluate flooding scope. The follow-up evidence required is: The planned area topology reaches distant prefixes through eligible Level 2 routing.

Incorrect Answers

A:

That result would be useful for a different failure, namely: A core engineer sees that IPv6 reachability is absent despite IS-IS adjacency and concludes the adjacency itself is broken. The current case specifically calls for: Place the correct L1/L2 boundary and evaluate flooding scope. The required observed result is: The planned area topology reaches distant prefixes through eligible Level 2 routing.

B:

This response would target a different source scenario: A service provider tags prefixes for selective export but applies the community-match policy to the wrong neighbor group. It cannot establish the current acceptance requirement, which is: The planned area topology reaches distant prefixes through eligible Level 2 routing. The relevant action is: Place the correct L1/L2 boundary and evaluate flooding scope.

C:

Rehearse the failure and inspect active next hops and IS-IS route changes is a relevant step for the separate scenario in which a provider failover exposes an alternate IS-IS path that had never been tested for next-hop resolution. It does not directly fix this case. Instead place the correct L1/L2 boundary and evaluate flooding scope; verify: The planned area topology reaches distant prefixes through eligible Level 2 routing.

Question 765

An aggregated customer advertisement persists while all contributing specifics have withdrawn. Which underlying Junos networking principle explains the failure?

  1. Protocol behavior: Multi-area OSPF design requires attention to backbone connectivity.
  2. Underlying principle: Aggregation can hide individual component failures if advertisement policy is not controlled.
  3. Root design issue: Imported routes must be validated in the destination lookup context.
  4. The governing rule is: Summary advertisements require validation against their underlying active route policy.

Explanation

Correct Answer

D:

The selected response implements the principle that summary advertisements require validation against their underlying active route policy. The engineer should audit aggregate or generated-route contributors and policy conditions. Successful confirmation means: A loss-of-last-contributor test causes the intended summary behavior.

Incorrect Answers

A:

This option overlooks the decisive condition. Its supporting principle is multi-area OSPF design requires attention to backbone connectivity, while this scenario depends on summary advertisements require validation against their underlying active route policy. Verify the correction with: A loss-of-last-contributor test causes the intended summary behavior.

B:

Aggregation can hide individual component failures if advertisement policy is not controlled describes a neighboring protocol concern. In this case the controlling fact is summary advertisements require validation against their underlying active route policy. A correct remediation would audit aggregate or generated-route contributors and policy conditions and demonstrate: A loss-of-last-contributor test causes the intended summary behavior.

C:

The proposed principle concerns another network fault: Imported routes must be validated in the destination lookup context. Here, summary advertisements require validation against their underlying active route policy. The most direct correction is to audit aggregate or generated-route contributors and policy conditions, confirmed by a loss-of-last-contributor test causes the intended summary behavior.

Question 766

A site complains an IRB gateway answers locally but the downstream VLAN has no remote MAC learning. What diagnosis and engineering response are most appropriate?

  1. Fault mechanism: Protective edge-port shutdown is evidence of BPDU policy enforcement. Remediation: Verify the BPDU protection event and remove the unauthorized bridge rather than blindly disabling safeguards.
  2. Root issue: Layer 2 isolation depends on bridge-domain and logical switch boundaries. Correction: Separate customer bridge domains and validate virtual-switch membership.
  3. Cause: MAC table visibility alone does not prove trunk authorization for every VLAN. Response: Inspect VLAN membership and tagging on both ends and verify per-VLAN MAC learning.
  4. Diagnosis: A working IRB gateway does not validate all L2 paths and trunk members. Action: Trace trunk authorization, bridge-domain membership and MAC learning across the path.

Explanation

Correct Answer

D:

This is the model-intended best choice because a working IRB gateway does not validate all L2 paths and trunk members. The targeted correction is to trace trunk authorization, bridge-domain membership and MAC learning across the path. Validate it by observing that both local and remote MACs learn in the intended bridge domain and hosts communicate.

Incorrect Answers

A:

Verify the BPDU protection event and remove the unauthorized bridge rather than blindly disabling safeguards is a relevant step for the separate scenario in which a customer plugs a small unmanaged switch into a protected edge port and the port disables as soon as BPDUs arrive. It does not directly fix this case. Instead trace trunk authorization, bridge-domain membership and MAC learning across the path; verify: Both local and remote MACs learn in the intended bridge domain and hosts communicate.

B:

The alternative addresses a customer bridge-domain spans two isolated customers due to reusing a virtual switch without tenant boundaries, not the present root cause. Here the selected correction must reflect a working IRB gateway does not validate all L2 paths and trunk members. Test for: Both local and remote MACs learn in the intended bridge domain and hosts communicate.

C:

This answer would be more suitable when after a trunk change a MAC address is visible but only one of two VLANs can traverse the uplink, where the corrective action is to inspect VLAN membership and tagging on both ends and verify per-VLAN MAC learning. The failure here is different: A working IRB gateway does not validate all L2 paths and trunk members. Required validation: Both local and remote MACs learn in the intended bridge domain and hosts communicate.

Question 767

A native untagged VLAN mismatch makes two switches place the same untagged frames into different segments. Which corrective action and confirmation pair is most appropriate?

  1. Change: Trace trunk authorization, bridge-domain membership and MAC learning across the path. Test: Both local and remote MACs learn in the intended bridge domain and hosts communicate.
  2. Implement: Evaluate BFD liveness detection with the associated routing protocol. Verify: A controlled forwarding failure is detected within the approved target.
  3. Control: Deploy or validate an integrated routing and bridging L3 interface and gateway. Accepted result: A test host reaches its gateway and an authorized remote subnet through IRB.
  4. Action: Align untagged or native VLAN behavior with explicit port configuration. Evidence: The same controlled untagged frame maps to the intended VLAN on both sides.

Explanation

Correct Answer

D:

Underlying cause: Untagged frame classification is local to the receiving interface. Corrective action: align untagged or native VLAN behavior with explicit port configuration. Verify the outcome: The same controlled untagged frame maps to the intended VLAN on both sides.

Incorrect Answers

A:

The proposed principle concerns another network fault: A working IRB gateway does not validate all L2 paths and trunk members. Here, untagged frame classification is local to the receiving interface. The most direct correction is to align untagged or native VLAN behavior with explicit port configuration, confirmed by the same controlled untagged frame maps to the intended VLAN on both sides.

B:

That result would be useful for a different failure, namely: A routing peer detects a dead neighbor too slowly for a real-time service even when the interface stays up. The current case specifically calls for: Align untagged or native VLAN behavior with explicit port configuration. The required observed result is: The same controlled untagged frame maps to the intended VLAN on both sides.

C:

This response would target a different source scenario: A VLAN provides local host connectivity but hosts cannot reach a different IP subnet through the bridge domain. It cannot establish the current acceptance requirement, which is: The same controlled untagged frame maps to the intended VLAN on both sides. The relevant action is: Align untagged or native VLAN behavior with explicit port configuration.

Question 768

A provider advertises a customer prefix with its own AS number already present in the return AS path. Which post-change observation most strongly confirms the correction?

  1. Verification result: The route is accepted only after the AS-path design is corrected.
  2. Closeout evidence: The expected IPv6 NLRI is received and becomes an eligible IPv6 route.
  3. Acceptance check: The intended inet6 family receives and selects the IPv6 prefix.
  4. The test confirms that the installed LSP avoids the prohibited link in a failure-free test.

Explanation

Correct Answer

A:

This is the model-intended best choice because bGP AS-path information can prevent routes from looping into an AS. The targeted correction is to investigate AS-path loop prevention rather than overriding it without risk review. Validate it by observing that the route is accepted only after the AS-path design is corrected.

Incorrect Answers

B:

This option overlooks the decisive condition. Its supporting principle is iPv4 BGP session liveness does not prove IPv6 family route exchange, while this scenario depends on bGP AS-path information can prevent routes from looping into an AS. Verify the correction with: The route is accepted only after the AS-path design is corrected.

C:

BGP transport connectivity does not guarantee every address family is negotiated and active describes a neighboring protocol concern. In this case the controlling fact is bGP AS-path information can prevent routes from looping into an AS. A correct remediation would investigate AS-path loop prevention rather than overriding it without risk review and demonstrate: The route is accepted only after the AS-path design is corrected.

D:

The proposed principle concerns another network fault: RSVP-TE path choice can account for configured topology constraints and resources. Here, bGP AS-path information can prevent routes from looping into an AS. The most direct correction is to investigate AS-path loop prevention rather than overriding it without risk review, confirmed by the route is accepted only after the AS-path design is corrected.

Question 769

An alternate uplink remains blocked after the primary path fails because expected BPDUs disappear. What action-and-test pairing directly resolves the case?

  1. Action: Verify the BPDU protection event and remove the unauthorized bridge rather than blindly disabling safeguards. Evidence: The approved endpoint reconnects without unexpected BPDUs and protection stays enabled.
  2. Repair: Inspect spanning-tree loop-protection events, root path and link state. Check: The corrected topology converges without opening an Ethernet loop.
  3. Change: Trace trunk authorization, bridge-domain membership and MAC learning across the path. Test: Both local and remote MACs learn in the intended bridge domain and hosts communicate.
  4. Implement: Match loop, BPDU and root protection to their different fault conditions. Verify: Separate fault injections trigger the intended protection per port role.

Explanation

Correct Answer

B:

The selected response implements the principle that loop protection can prevent unsafe forwarding when control-plane information is missing. The engineer should inspect spanning-tree loop-protection events, root path and link state. Successful confirmation means: The corrected topology converges without opening an Ethernet loop.

Incorrect Answers

A:

This response would target a different source scenario: A customer plugs a small unmanaged switch into a protected edge port and the port disables as soon as BPDUs arrive. It cannot establish the current acceptance requirement, which is: The corrected topology converges without opening an Ethernet loop. The relevant action is: Inspect spanning-tree loop-protection events, root path and link state.

C:

The alternative addresses a site complains an IRB gateway answers locally but the downstream VLAN has no remote MAC learning, not the present root cause. Here the selected correction must reflect loop protection can prevent unsafe forwarding when control-plane information is missing. Test for: The corrected topology converges without opening an Ethernet loop.

D:

This answer would be more suitable when an engineer uses loop protection as if it served the same purpose as BPDU protection on every port, where the corrective action is to match loop, BPDU and root protection to their different fault conditions. The failure here is different: Loop protection can prevent unsafe forwarding when control-plane information is missing. Required validation: The corrected topology converges without opening an Ethernet loop.

Question 770

A peer announces an IPv6 prefix but the operator checks only the IPv4 BGP route family. What observable result most directly verifies the intended configuration?

  1. The test confirms that the planned ABR topology provides verified interarea reachability.
  2. Expected observation: The internal router resolves the next hop and installs the intended route.
  3. Verification result: A test prefix reaches permitted clients without cycling through reflector clusters.
  4. Closeout evidence: The intended inet6 family receives and selects the IPv6 prefix.

Explanation

Correct Answer

D:

This option addresses the stated case rather than another networking issue. Principle: BGP transport connectivity does not guarantee every address family is negotiated and active. Remedy: Verify negotiated address families and family-specific routing tables. Proof: The intended inet6 family receives and selects the IPv6 prefix.

Incorrect Answers

A:

Multi-area OSPF design requires attention to backbone connectivity describes a neighboring protocol concern. In this case the controlling fact is bGP transport connectivity does not guarantee every address family is negotiated and active. A correct remediation would verify negotiated address families and family-specific routing tables and demonstrate: The intended inet6 family receives and selects the IPv6 prefix.

B:

The proposed principle concerns another network fault: Unresolvable BGP next hops can make received routes unusable. Here, bGP transport connectivity does not guarantee every address family is negotiated and active. The most direct correction is to verify negotiated address families and family-specific routing tables, confirmed by the intended inet6 family receives and selects the IPv6 prefix.

C:

That result would be useful for a different failure, namely: A route reflector advertises routes to the wrong clients after a change in group membership. The current case specifically calls for: Verify negotiated address families and family-specific routing tables. The required observed result is: The intended inet6 family receives and selects the IPv6 prefix.

Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests