mcAfee Secure Website
exam =5
exam =6

Exam Code: JN0-364

Exam Name: Service Provider Routing and Switching, Specialist (JNCIS-SP)

Certification Provider: Juniper

Juniper JN0-364 Questions & Answers

Reliable & Actual Study Materials for JN0-364 Exam Success

69 Questions & Answers with Testing Engine

"JN0-364: Service Provider Routing and Switching, Specialist (JNCIS-SP)" Testing Engine covers all the knowledge points of the real Juniper JN0-364 exam.

The latest actual JN0-364 Questions & Answers from Pass4sure. Everything you need to prepare and get best score at JN0-364 exam easily and quickly.

exam =7
Guarantee

Satisfaction Guaranteed

Pass4sure has a remarkable Juniper Candidate Success record. We're confident of our products and provide no hassle product exchange. That's how confident we are!

99.3% Pass Rate
Was: $137.49
Now: $124.99

Juniper JN0-364 Practice Test 30

Question 290

A provider configures an IPv6 static route but assumes IPv4 ARP will resolve its IPv6 neighbor. Which underlying Junos networking principle explains the failure?

  1. Protocol behavior: BGP family negotiation and route policy control IPv6 NLRI exchange.
  2. Underlying principle: IPv6 link-layer neighbor resolution uses ICMPv6 Neighbor Discovery.
  3. Root design issue: Underlying endpoint reachability does not guarantee permitted encapsulated payloads.
  4. The governing rule is: IS-IS shortest-path output depends on effective metrics across the route.

Explanation

Correct Answer

B:

This is the model-intended best choice because iPv6 link-layer neighbor resolution uses ICMPv6 Neighbor Discovery. The targeted correction is to distinguish IPv6 Neighbor Discovery from IPv4 ARP. Validate it by observing that the neighbor cache resolves the IPv6 next hop and traffic passes.

Incorrect Answers

A:

BGP family negotiation and route policy control IPv6 NLRI exchange describes a neighboring protocol concern. In this case the controlling fact is iPv6 link-layer neighbor resolution uses ICMPv6 Neighbor Discovery. A correct remediation would distinguish IPv6 Neighbor Discovery from IPv4 ARP and demonstrate: The neighbor cache resolves the IPv6 next hop and traffic passes.

C:

That result would be useful for a different failure, namely: IPv6-over-IPv4 tunnel endpoints reach each other using IPv4 but IPv6 payloads fail after a firewall update. The current case specifically calls for: Distinguish IPv6 Neighbor Discovery from IPv4 ARP. The required observed result is: The neighbor cache resolves the IPv6 next hop and traffic passes.

D:

This response would target a different source scenario: A transit operator changes IS-IS metrics on one interface and later discovers a traffic-engineering imbalance. It cannot establish the current acceptance requirement, which is: The neighbor cache resolves the IPv6 next hop and traffic passes. The relevant action is: Distinguish IPv6 Neighbor Discovery from IPv4 ARP.

Question 291

An iBGP route is hidden because the next hop learned from an edge router is unreachable inside the backbone. Which test result would best confirm a successful fix?

  1. Acceptance check: The segment passes route and database tests with the expected neighbor states.
  2. The test confirms that the internal router resolves the next hop and installs the intended route.
  3. Expected observation: A test prefix reaches permitted clients without cycling through reflector clusters.
  4. Verification result: The expected IPv6 NLRI is received and becomes an eligible IPv6 route.

Explanation

Correct Answer

B:

Underlying cause: Unresolvable BGP next hops can make received routes unusable. Corrective action: restore appropriate IGP next-hop reachability or approved next-hop-self behavior. Verify the outcome: The internal router resolves the next hop and installs the intended route.

Incorrect Answers

A:

The alternative addresses a broadcast core VLAN has only one Full adjacency and the engineer wants to reset all routers immediately, not the present root cause. Here the selected correction must reflect unresolvable BGP next hops can make received routes unusable. Test for: The internal router resolves the next hop and installs the intended route.

C:

This option overlooks the decisive condition. Its supporting principle is route reflection relies on correct client boundaries and originator or cluster tracking, while this scenario depends on unresolvable BGP next hops can make received routes unusable. Verify the correction with: The internal router resolves the next hop and installs the intended route.

D:

IPv4 BGP session liveness does not prove IPv6 family route exchange describes a neighboring protocol concern. In this case the controlling fact is unresolvable BGP next hops can make received routes unusable. A correct remediation would restore appropriate IGP next-hop reachability or approved next-hop-self behavior and demonstrate: The internal router resolves the next hop and installs the intended route.

Question 292

A VRRP backup router does not take over when the primary gateway interface is disabled. What observable result most directly verifies the intended configuration?

  1. Closeout evidence: A controlled switchover retains the expected bridge state and host connectivity.
  2. Acceptance check: The backup assumes master role and clients retain access to the virtual gateway.
  3. The test confirms that the configuration commits with an approved supported HA combination.
  4. Expected observation: After fiber repair the port converges and remains in a stable role.

Explanation

Correct Answer

B:

Because failover depends on compatible virtual router configuration and observable primary loss, the best response is to check VRRP group, interface, priority, advertisements and tracking conditions. A reviewer can close the technical case only after confirming that the backup assumes master role and clients retain access to the virtual gateway.

Incorrect Answers

A:

That result would be useful for a different failure, namely: Layer 2 forwarding is disrupted during Routing Engine replacement even though high availability was enabled for routing. The current case specifically calls for: Check VRRP group, interface, priority, advertisements and tracking conditions. The required observed result is: The backup assumes master role and clients retain access to the virtual gateway.

C:

Review supported mutual exclusivity and select the intended HA control-plane method is a relevant step for the separate scenario in which a provider tries to enable nonstop active routing and graceful-restart mode simultaneously on the same Junos device. It does not directly fix this case. Instead check VRRP group, interface, priority, advertisements and tracking conditions; verify: The backup assumes master role and clients retain access to the virtual gateway.

D:

The alternative addresses an RSTP uplink continues to flap between discarding and forwarding after an unstable fiber replacement, not the present root cause. Here the selected correction must reflect failover depends on compatible virtual router configuration and observable primary loss. Test for: The backup assumes master role and clients retain access to the virtual gateway.

Question 293

A generated route is configured but its expected contributing route is absent from the routing table. What should the operations engineer do first to address the stated fault?

  1. Apply this control: Verify route contribution and the conditions for route generation.
  2. Remediation: Trace the applicable BGP route-selection steps and local policies.
  3. Recommended change: Restrict routing-policy matches and validate the import and export boundary.
  4. Next step: Validate forwarding load-sharing configuration and run representative multi-flow traffic.

Explanation

Correct Answer

A:

The critical observation is: A generated route depends on its contributing-route conditions rather than mere configuration presence. Correct it by taking this action: Verify route contribution and the conditions for route generation. Confirm the outcome with: The generated prefix appears only when the required contributing route is active.

Incorrect Answers

B:

BGP selection is policy-driven and is not equivalent to IGP least-hop routing describes a neighboring protocol concern. In this case the controlling fact is a generated route depends on its contributing-route conditions rather than mere configuration presence. A correct remediation would verify route contribution and the conditions for route generation and demonstrate: The generated prefix appears only when the required contributing route is active.

C:

The proposed principle concerns another network fault: Route redistribution must be intentionally scoped to prevent cross-tenant leakage. Here, a generated route depends on its contributing-route conditions rather than mere configuration presence. The most direct correction is to verify route contribution and the conditions for route generation, confirmed by the generated prefix appears only when the required contributing route is active.

D:

That result would be useful for a different failure, namely: An equal-cost path test sends nearly all flows across one member while both links remain operational. The current case specifically calls for: Verify route contribution and the conditions for route generation. The required observed result is: The generated prefix appears only when the required contributing route is active.

Question 294

An access switch forwards untagged traffic into VLAN 20 after a port is moved to VLAN 30. Which test result would best confirm a successful fix?

  1. Expected observation: The bridge domain and IRB interface share the configured gateway context.
  2. Verification result: The moved test port places incoming untagged frames only in VLAN 30.
  3. Closeout evidence: A test host ARPs or discovers its gateway and routes to the intended subnet.
  4. Acceptance check: A tested switchover maintains the required liveness behavior without false failure.

Explanation

Correct Answer

B:

This option addresses the stated case rather than another networking issue. Principle: VLAN reassignment must be verified in actual port classification. Remedy: Check committed access VLAN settings and operational membership rather than relying on notes. Proof: The moved test port places incoming untagged frames only in VLAN 30.

Incorrect Answers

A:

Verify VLAN or bridge-domain membership and its L3 IRB binding is a relevant step for the separate scenario in which an IRB interface is present but an operator assumes it creates a bridge domain automatically. It does not directly fix this case. Instead check committed access VLAN settings and operational membership rather than relying on notes; verify: The moved test port places incoming untagged frames only in VLAN 30.

C:

This answer would be more suitable when a router-on-a-stick replacement with IRB stops reachability between a bridge domain and an L3 subnet, where the corrective action is to verify VLAN-to-IRB interface binding, addresses and active route entries. The failure here is different: VLAN reassignment must be verified in actual port classification. Required validation: The moved test port places incoming untagged frames only in VLAN 30.

D:

This option overlooks the decisive condition. Its supporting principle is bFD HA behavior depends on platform processing placement and timer tolerances, while this scenario depends on vLAN reassignment must be verified in actual port classification. Verify the correction with: The moved test port places incoming untagged frames only in VLAN 30.

Question 295

A switch has a root port and alternate port, but the operator assumes both must forward to use all physical bandwidth. What assessment accurately links the fault to its correction?

  1. Root issue: RSTP can converge faster using explicit roles and handshakes where conditions allow. Correction: Compare the rapid proposal/agreement behavior with traditional timer-dependent transitions.
  2. Cause: Protective edge-port shutdown is evidence of BPDU policy enforcement. Response: Verify the BPDU protection event and remove the unauthorized bridge rather than blindly disabling safeguards.
  3. Diagnosis: MAC table visibility alone does not prove trunk authorization for every VLAN. Action: Inspect VLAN membership and tagging on both ends and verify per-VLAN MAC learning.
  4. Explanation: A redundant alternate path can remain nonforwarding until a failure changes roles. Repair: Explain root and alternate roles in a loop-free spanning-tree topology.

Explanation

Correct Answer

D:

Underlying cause: A redundant alternate path can remain nonforwarding until a failure changes roles. Corrective action: explain root and alternate roles in a loop-free spanning-tree topology. Verify the outcome: The alternate port transitions appropriately after the root path fails.

Incorrect Answers

A:

The proposed principle concerns another network fault: RSTP can converge faster using explicit roles and handshakes where conditions allow. Here, a redundant alternate path can remain nonforwarding until a failure changes roles. The most direct correction is to explain root and alternate roles in a loop-free spanning-tree topology, confirmed by the alternate port transitions appropriately after the root path fails.

B:

That result would be useful for a different failure, namely: A customer plugs a small unmanaged switch into a protected edge port and the port disables as soon as BPDUs arrive. The current case specifically calls for: Explain root and alternate roles in a loop-free spanning-tree topology. The required observed result is: The alternate port transitions appropriately after the root path fails.

C:

This response would target a different source scenario: After a trunk change a MAC address is visible but only one of two VLANs can traverse the uplink. It cannot establish the current acceptance requirement, which is: The alternate port transitions appropriately after the root path fails. The relevant action is: Explain root and alternate roles in a loop-free spanning-tree topology.

Question 296

An engineer uses loop protection as if it served the same purpose as BPDU protection on every port. Which change best corrects the failure without losing the intended design?

  1. Recommended change: Apply supported root protection at the appropriate customer-facing boundary.
  2. Next step: Inspect VLAN membership and tagging on both ends and verify per-VLAN MAC learning.
  3. Corrective action: Review root bridge priority and MAC-based bridge identifier comparison.
  4. Apply this control: Match loop, BPDU and root protection to their different fault conditions.

Explanation

Correct Answer

D:

Because spanning-tree security mechanisms protect distinct topology and control-plane risks, the best response is to match loop, BPDU and root protection to their different fault conditions. A reviewer can close the technical case only after confirming that separate fault injections trigger the intended protection per port role.

Incorrect Answers

A:

This answer would be more suitable when a provider STP domain changes root when a customer sends superior BPDUs from an access port, where the corrective action is to apply supported root protection at the appropriate customer-facing boundary. The failure here is different: Spanning-tree security mechanisms protect distinct topology and control-plane risks. Required validation: Separate fault injections trigger the intended protection per port role.

B:

This option overlooks the decisive condition. Its supporting principle is mAC table visibility alone does not prove trunk authorization for every VLAN, while this scenario depends on spanning-tree security mechanisms protect distinct topology and control-plane risks. Verify the correction with: Separate fault injections trigger the intended protection per port role.

C:

Traditional spanning-tree root election favors the lowest bridge ID describes a neighboring protocol concern. In this case the controlling fact is spanning-tree security mechanisms protect distinct topology and control-plane risks. A correct remediation would match loop, BPDU and root protection to their different fault conditions and demonstrate: Separate fault injections trigger the intended protection per port role.

Question 297

A route leaked to a second routing table unexpectedly carries a next hop that cannot be resolved there. What action-and-test pairing directly resolves the case?

  1. Change: Verify route contribution and the conditions for route generation. Test: The generated prefix appears only when the required contributing route is active.
  2. Implement: Trace the applicable BGP route-selection steps and local policies. Verify: The chosen path matches the configured preference and applicable attributes.
  3. Control: Audit aggregate or generated-route contributors and policy conditions. Accepted result: A loss-of-last-contributor test causes the intended summary behavior.
  4. Action: Evaluate routing-table relationships and next-hop resolution when using RIB groups. Evidence: The imported route resolves and forwarding behavior matches the intended instance.

Explanation

Correct Answer

D:

The case turns on the distinction that moving route information between tables does not remove the need for a valid forwarding next hop. Apply this concrete engineering step: Evaluate routing-table relationships and next-hop resolution when using RIB groups. An acceptable verification outcome is: The imported route resolves and forwarding behavior matches the intended instance.

Incorrect Answers

A:

This response would target a different source scenario: A generated route is configured but its expected contributing route is absent from the routing table. It cannot establish the current acceptance requirement, which is: The imported route resolves and forwarding behavior matches the intended instance. The relevant action is: Evaluate routing-table relationships and next-hop resolution when using RIB groups.

B:

Trace the applicable BGP route-selection steps and local policies is a relevant step for the separate scenario in which a router learns the same prefix from peers in distinct autonomous systems but the engineer compares only BGP hop count. It does not directly fix this case. Instead evaluate routing-table relationships and next-hop resolution when using RIB groups; verify: The imported route resolves and forwarding behavior matches the intended instance.

C:

The alternative addresses an aggregated customer advertisement persists while all contributing specifics have withdrawn, not the present root cause. Here the selected correction must reflect moving route information between tables does not remove the need for a valid forwarding next hop. Test for: The imported route resolves and forwarding behavior matches the intended instance.

Question 298

A provider STP domain changes root when a customer sends superior BPDUs from an access port. What implementation step and validation result should be selected?

  1. Repair: Review root bridge priority and MAC-based bridge identifier comparison. Check: The intended device is root under the tested priorities and tie-breakers.
  2. Change: Apply supported root protection at the appropriate customer-facing boundary. Test: A superior BPDU test preserves the intended root with a logged protective state.
  3. Implement: Check VRRP group, interface, priority, advertisements and tracking conditions. Verify: The backup assumes master role and clients retain access to the virtual gateway.
  4. Control: Verify the BPDU protection event and remove the unauthorized bridge rather than blindly disabling safeguards. Accepted result: The approved endpoint reconnects without unexpected BPDUs and protection stays enabled.

Explanation

Correct Answer

B:

This is the model-intended best choice because customer control traffic must not displace the authorized provider root. The targeted correction is to apply supported root protection at the appropriate customer-facing boundary. Validate it by observing that a superior BPDU test preserves the intended root with a logged protective state.

Incorrect Answers

A:

Traditional spanning-tree root election favors the lowest bridge ID describes a neighboring protocol concern. In this case the controlling fact is customer control traffic must not displace the authorized provider root. A correct remediation would apply supported root protection at the appropriate customer-facing boundary and demonstrate: A superior BPDU test preserves the intended root with a logged protective state.

C:

That result would be useful for a different failure, namely: A VRRP backup router does not take over when the primary gateway interface is disabled. The current case specifically calls for: Apply supported root protection at the appropriate customer-facing boundary. The required observed result is: A superior BPDU test preserves the intended root with a logged protective state.

D:

This response would target a different source scenario: A customer plugs a small unmanaged switch into a protected edge port and the port disables as soon as BPDUs arrive. It cannot establish the current acceptance requirement, which is: A superior BPDU test preserves the intended root with a logged protective state. The relevant action is: Apply supported root protection at the appropriate customer-facing boundary.

Question 299

A branch uses a higher OSPF interface cost but expects that branch to remain the preferred primary path. Which next action best resolves this observed routing or switching failure?

  1. Corrective action: Compare received LSAs with route selection, area eligibility and next-hop resolution.
  2. Apply this control: Verify route contribution and the conditions for route generation.
  3. Remediation: Revisit additive path cost and verify SPF outcomes across alternative links.
  4. Recommended change: Review router priorities and the nonpreemptive properties of DR elections.

Explanation

Correct Answer

C:

The selected response implements the principle that oSPF normally prefers the least accumulated metric to a destination. The engineer should revisit additive path cost and verify SPF outcomes across alternative links. Successful confirmation means: The intended lower-total-cost path wins under steady-state conditions.

Incorrect Answers

A:

The alternative addresses an OSPF packet capture shows Link State Updates but the route remains hidden from the active table, not the present root cause. Here the selected correction must reflect oSPF normally prefers the least accumulated metric to a destination. Test for: The intended lower-total-cost path wins under steady-state conditions.

B:

This answer would be more suitable when a generated route is configured but its expected contributing route is absent from the routing table, where the corrective action is to verify route contribution and the conditions for route generation. The failure here is different: OSPF normally prefers the least accumulated metric to a destination. Required validation: The intended lower-total-cost path wins under steady-state conditions.

D:

OSPF DR selection depends on eligible routers and the current election event describes a neighboring protocol concern. In this case the controlling fact is oSPF normally prefers the least accumulated metric to a destination. A correct remediation would revisit additive path cost and verify SPF outcomes across alternative links and demonstrate: The intended lower-total-cost path wins under steady-state conditions.

Question 300

A Junos router shows no IS-IS adjacency after a circuit migration though the interface is physically up. Which protocol behavior most directly determines the correct diagnosis?

  1. Protocol behavior: A backup path requires functional forwarding, not merely topology presence.
  2. Underlying principle: IS-IS routing levels determine topology knowledge and area reachability.
  3. Root design issue: Layered neighbor troubleshooting should separate transport from OSPF parameter mismatches.
  4. The governing rule is: An operational interface is not evidence of matching IS-IS protocol configuration.

Explanation

Correct Answer

D:

Correct diagnosis: An operational interface is not evidence of matching IS-IS protocol configuration. The appropriate action is: Inspect IS-IS interface enablement, levels, area identifiers and link type. The follow-up evidence required is: The corrected circuit shows the expected neighbor and link-state entries.

Incorrect Answers

A:

That result would be useful for a different failure, namely: A provider failover exposes an alternate IS-IS path that had never been tested for next-hop resolution. The current case specifically calls for: Inspect IS-IS interface enablement, levels, area identifiers and link type. The required observed result is: The corrected circuit shows the expected neighbor and link-state entries.

B:

This response would target a different source scenario: A router learns a local IS-IS topology but cannot infer reachability in a remote area from its Level 1-only view. It cannot establish the current acceptance requirement, which is: The corrected circuit shows the expected neighbor and link-state entries. The relevant action is: Inspect IS-IS interface enablement, levels, area identifiers and link type.

C:

Compare area, interface mode, timers, authentication and physical status on both endpoints is a relevant step for the separate scenario in which a new OSPF uplink remains down at the adjacency stage after a router replacement. It does not directly fix this case. Instead inspect IS-IS interface enablement, levels, area identifiers and link type; verify: The corrected circuit shows the expected neighbor and link-state entries.

Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests