mcAfee Secure Website
exam =5
exam =6

Exam Code: JN0-364

Exam Name: Service Provider Routing and Switching, Specialist (JNCIS-SP)

Certification Provider: Juniper

Juniper JN0-364 Questions & Answers

Reliable & Actual Study Materials for JN0-364 Exam Success

69 Questions & Answers with Testing Engine

"JN0-364: Service Provider Routing and Switching, Specialist (JNCIS-SP)" Testing Engine covers all the knowledge points of the real Juniper JN0-364 exam.

The latest actual JN0-364 Questions & Answers from Pass4sure. Everything you need to prepare and get best score at JN0-364 exam easily and quickly.

exam =7
Guarantee

Satisfaction Guaranteed

Pass4sure has a remarkable Juniper Candidate Success record. We're confident of our products and provide no hassle product exchange. That's how confident we are!

99.3% Pass Rate
Was: $137.49
Now: $124.99

Juniper JN0-364 Practice Test 54

Question 530

An iBGP route is hidden because the next hop learned from an edge router is unreachable inside the backbone. What remediation is most directly applicable?

  1. Recommended change: Distinguish internal LSAs from externally originated route information.
  2. Next step: Trace the applicable BGP route-selection steps and local policies.
  3. Corrective action: Restore appropriate IGP next-hop reachability or approved next-hop-self behavior.
  4. Apply this control: Confirm the configured local and peer AS values with the authoritative design.

Explanation

Correct Answer

C:

Correct diagnosis: Unresolvable BGP next hops can make received routes unusable. The appropriate action is: Restore appropriate IGP next-hop reachability or approved next-hop-self behavior. The follow-up evidence required is: The internal router resolves the next hop and installs the intended route.

Incorrect Answers

A:

OSPF route type and LSA scope depend on where routing information originates describes a neighboring protocol concern. In this case the controlling fact is unresolvable BGP next hops can make received routes unusable. A correct remediation would restore appropriate IGP next-hop reachability or approved next-hop-self behavior and demonstrate: The internal router resolves the next hop and installs the intended route.

B:

The proposed principle concerns another network fault: BGP selection is policy-driven and is not equivalent to IGP least-hop routing. Here, unresolvable BGP next hops can make received routes unusable. The most direct correction is to restore appropriate IGP next-hop reachability or approved next-hop-self behavior, confirmed by the internal router resolves the next hop and installs the intended route.

D:

This response would target a different source scenario: A remote BGP neighbor uses a different AS number than configured and the session fails during OPEN negotiation. It cannot establish the current acceptance requirement, which is: The internal router resolves the next hop and installs the intended route. The relevant action is: Restore appropriate IGP next-hop reachability or approved next-hop-self behavior.

Question 531

A planned root bridge migration is configured but the operational root remains on the old switch. A reviewer requires a remedy and concrete test evidence. Which pairing fits?

  1. Change: Review root bridge priority and MAC-based bridge identifier comparison. Test: The intended device is root under the tested priorities and tie-breakers.
  2. Implement: Review allowed VLAN membership on both trunk endpoints. Verify: Both permitted VLAN test flows cross while an explicitly denied VLAN stays blocked.
  3. Control: Compare root priority, bridge identifiers and current STP topology status. Accepted result: A controlled election yields the approved root with documented path changes.
  4. Action: Inspect per-VLAN STP instances and configured priorities, not just a global STP summary. Evidence: Each tested VLAN elects its approved root and loop-free port roles.

Explanation

Correct Answer

C:

The selected response implements the principle that configuration intent must be verified against the actual elected spanning-tree root. The engineer should compare root priority, bridge identifiers and current STP topology status. Successful confirmation means: A controlled election yields the approved root with documented path changes.

Incorrect Answers

A:

The alternative addresses a switch operator treats the highest bridge ID as the guaranteed STP root, not the present root cause. Here the selected correction must reflect configuration intent must be verified against the actual elected spanning-tree root. Test for: A controlled election yields the approved root with documented path changes.

B:

This answer would be more suitable when a trunk permits VLAN 110 but excludes VLAN 120 while users on VLAN 120 report isolation from the remote switch, where the corrective action is to review allowed VLAN membership on both trunk endpoints. The failure here is different: Configuration intent must be verified against the actual elected spanning-tree root. Required validation: A controlled election yields the approved root with documented path changes.

D:

Per-VLAN spanning-tree behavior can differ across VLANs describes a neighboring protocol concern. In this case the controlling fact is configuration intent must be verified against the actual elected spanning-tree root. A correct remediation would compare root priority, bridge identifiers and current STP topology status and demonstrate: A controlled election yields the approved root with documented path changes.

Question 532

A penultimate router pops a transport label and the egress receives native IP even though the engineer expected a visible final outer label. Which technical distinction best describes the observed symptom?

  1. Root design issue: An upstream LSR can remove a label before the egress in an appropriate PHP design.
  2. The governing rule is: MPLS forwarding typically uses labels to select the next label-switched hop.
  3. The key distinction is: BGP selection is policy-driven and is not equivalent to IGP least-hop routing.
  4. Protocol behavior: An LSP cannot follow an unavailable required hop.

Explanation

Correct Answer

A:

This option addresses the stated case rather than another networking issue. Principle: An upstream LSR can remove a label before the egress in an appropriate PHP design. Remedy: Recognize penultimate-hop popping as an allowed LSP forwarding behavior. Proof: A packet trace verifies the intended stack at the penultimate and egress hops.

Incorrect Answers

B:

This response would target a different source scenario: An operator expects an MPLS label to represent an entire customer IP packet header. It cannot establish the current acceptance requirement, which is: A packet trace verifies the intended stack at the penultimate and egress hops. The relevant action is: Recognize penultimate-hop popping as an allowed LSP forwarding behavior.

C:

Trace the applicable BGP route-selection steps and local policies is a relevant step for the separate scenario in which a router learns the same prefix from peers in distinct autonomous systems but the engineer compares only BGP hop count. It does not directly fix this case. Instead recognize penultimate-hop popping as an allowed LSP forwarding behavior; verify: A packet trace verifies the intended stack at the penultimate and egress hops.

D:

The alternative addresses an operator configured an explicit RSVP path through a link that is now administratively down, not the present root cause. Here the selected correction must reflect an upstream LSR can remove a label before the egress in an appropriate PHP design. Test for: A packet trace verifies the intended stack at the penultimate and egress hops.

Question 533

A new Junos edge router can ping IPv4 customers but cannot route IPv6 traffic to the same site. A reviewer requires a remedy and concrete test evidence. Which pairing fits?

  1. Action: Distinguish the inner routed payload from outer unicast encapsulation. Evidence: Underlay traces show the outer endpoint traffic without transit processing of inner routes.
  2. Repair: Verify tunnel protocol allowance, endpoint encapsulation and effective MTU. Check: IPv6 test packets traverse the restored tunnel with appropriate MTU handling.
  3. Change: Distinguish IPv6 Neighbor Discovery from IPv4 ARP. Test: The neighbor cache resolves the IPv6 next hop and traffic passes.
  4. Implement: Validate IPv6 addressing, neighbor discovery and inet6 routing separately. Verify: The intended IPv6 neighbor and destination routes appear and traffic succeeds.

Explanation

Correct Answer

D:

The selected response implements the principle that iPv4 operational success does not prove IPv6 forwarding configuration. The engineer should validate IPv6 addressing, neighbor discovery and inet6 routing separately. Successful confirmation means: The intended IPv6 neighbor and destination routes appear and traffic succeeds.

Incorrect Answers

A:

This option overlooks the decisive condition. Its supporting principle is a tunnel can carry inner packet types over an underlay forwarding only the outer header, while this scenario depends on iPv4 operational success does not prove IPv6 forwarding configuration. Verify the correction with: The intended IPv6 neighbor and destination routes appear and traffic succeeds.

B:

Underlying endpoint reachability does not guarantee permitted encapsulated payloads describes a neighboring protocol concern. In this case the controlling fact is iPv4 operational success does not prove IPv6 forwarding configuration. A correct remediation would validate IPv6 addressing, neighbor discovery and inet6 routing separately and demonstrate: The intended IPv6 neighbor and destination routes appear and traffic succeeds.

C:

The proposed principle concerns another network fault: IPv6 link-layer neighbor resolution uses ICMPv6 Neighbor Discovery. Here, iPv4 operational success does not prove IPv6 forwarding configuration. The most direct correction is to validate IPv6 addressing, neighbor discovery and inet6 routing separately, confirmed by the intended IPv6 neighbor and destination routes appear and traffic succeeds.

Question 534

A BGP prefix remains rejected after an intended route filter update because an earlier term rejects it. Which test result would best confirm a successful fix?

  1. The test confirms that the adjacency advances through database synchronization to Full.
  2. Expected observation: Traffic uses the primary provider until the documented failover condition occurs.
  3. Verification result: The approved route matches an accepting term and the denied route remains denied.
  4. Closeout evidence: A test prefix reaches permitted clients without cycling through reflector clusters.

Explanation

Correct Answer

C:

Because policy evaluation order can short-circuit later intended acceptance, the best response is to evaluate policy terms in effective order and test matching routes. A reviewer can close the technical case only after confirming that the approved route matches an accepting term and the denied route remains denied.

Incorrect Answers

A:

Check MTU and interface compatibility and inspect neighbor-state details is a relevant step for the separate scenario in which an OSPF trace shows Hellos received but database synchronization stalls at ExStart or Exchange. It does not directly fix this case. Instead evaluate policy terms in effective order and test matching routes; verify: The approved route matches an accepting term and the denied route remains denied.

B:

The alternative addresses a policy change unexpectedly makes a backup transit provider carry most outbound traffic, not the present root cause. Here the selected correction must reflect policy evaluation order can short-circuit later intended acceptance. Test for: The approved route matches an accepting term and the denied route remains denied.

D:

This option overlooks the decisive condition. Its supporting principle is route reflection relies on correct client boundaries and originator or cluster tracking, while this scenario depends on policy evaluation order can short-circuit later intended acceptance. Verify the correction with: The approved route matches an accepting term and the denied route remains denied.

Question 535

A link-state database shows intra-area information but a site expects external routes from an unconfigured redistribution policy. Which next action best resolves this observed routing or switching failure?

  1. Recommended change: Assign distinct stable router IDs and clear stale protocol state using an approved procedure.
  2. Next step: Evaluate routing-table relationships and next-hop resolution when using RIB groups.
  3. Corrective action: Compare Hello/Dead event logs with loss and interface errors before tuning timers.
  4. Apply this control: Distinguish internal LSAs from externally originated route information.

Explanation

Correct Answer

D:

Underlying cause: OSPF route type and LSA scope depend on where routing information originates. Corrective action: distinguish internal LSAs from externally originated route information. Verify the outcome: The expected redistributed prefix appears with the right OSPF route type.

Incorrect Answers

A:

The proposed principle concerns another network fault: OSPF identifies speakers by router ID, which must be unique inside a routing domain. Here, oSPF route type and LSA scope depend on where routing information originates. The most direct correction is to distinguish internal LSAs from externally originated route information, confirmed by the expected redistributed prefix appears with the right OSPF route type.

B:

That result would be useful for a different failure, namely: A route leaked to a second routing table unexpectedly carries a next hop that cannot be resolved there. The current case specifically calls for: Distinguish internal LSAs from externally originated route information. The required observed result is: The expected redistributed prefix appears with the right OSPF route type.

C:

This response would target a different source scenario: Several routers report intermittent OSPF neighbor resets on a saturated transit circuit. It cannot establish the current acceptance requirement, which is: The expected redistributed prefix appears with the right OSPF route type. The relevant action is: Distinguish internal LSAs from externally originated route information.

Question 536

An Ethernet access design has multiple logical units using one physical port without specifying frame encapsulation. Which root-cause explanation and corrective action fit the case?

  1. Explanation: Ethernet forwarding uses bridge-domain context rather than arbitrary IP-route matching. Repair: Trace frame classification and virtual-switch bridge-domain association.
  2. Fault mechanism: A redundant alternate path can remain nonforwarding until a failure changes roles. Remediation: Explain root and alternate roles in a loop-free spanning-tree topology.
  3. Root issue: Port mode determines which customer frames are tagged or untagged at the boundary. Correction: Distinguish access port traffic from trunk tagging behavior.
  4. Cause: Logical service segmentation requires the physical Ethernet encapsulation to match the intended tag model. Response: Document VLAN-aware versus flexible tagging and unit classification requirements.

Explanation

Correct Answer

D:

Because logical service segmentation requires the physical Ethernet encapsulation to match the intended tag model, the best response is to document VLAN-aware versus flexible tagging and unit classification requirements. A reviewer can close the technical case only after confirming that both test logical units classify tagged traffic into their intended bridge domains.

Incorrect Answers

A:

This answer would be more suitable when a port belongs to a VLAN but traffic to a remote site is forwarded through a different bridge domain, where the corrective action is to trace frame classification and virtual-switch bridge-domain association. The failure here is different: Logical service segmentation requires the physical Ethernet encapsulation to match the intended tag model. Required validation: Both test logical units classify tagged traffic into their intended bridge domains.

B:

This option overlooks the decisive condition. Its supporting principle is a redundant alternate path can remain nonforwarding until a failure changes roles, while this scenario depends on logical service segmentation requires the physical Ethernet encapsulation to match the intended tag model. Verify the correction with: Both test logical units classify tagged traffic into their intended bridge domains.

C:

Port mode determines which customer frames are tagged or untagged at the boundary describes a neighboring protocol concern. In this case the controlling fact is logical service segmentation requires the physical Ethernet encapsulation to match the intended tag model. A correct remediation would document VLAN-aware versus flexible tagging and unit classification requirements and demonstrate: Both test logical units classify tagged traffic into their intended bridge domains.

Question 537

An operator configured an explicit RSVP path through a link that is now administratively down. Which technical distinction best describes the observed symptom?

  1. Root design issue: An LSP cannot follow an unavailable required hop.
  2. The governing rule is: LDP signaling depends on the routing and transport state of its endpoints.
  3. The key distinction is: RSVP-TE path choice can account for configured topology constraints and resources.
  4. Protocol behavior: Routing policy changes can override expected primary and backup peering intent.

Explanation

Correct Answer

A:

Underlying cause: An LSP cannot follow an unavailable required hop. Corrective action: update the engineered path constraints and verify candidate topology availability. Verify the outcome: The backup LSP establishes on a permitted alternate path.

Incorrect Answers

B:

Check transport reachability, LDP session state and the relevant IGP routes is a relevant step for the separate scenario in which a provider's LDP neighbors disappear after an IGP outage while physical links remain up. It does not directly fix this case. Instead update the engineered path constraints and verify candidate topology availability; verify: The backup LSP establishes on a permitted alternate path.

C:

The alternative addresses an RSVP LSP needs to avoid a congested link but its path is left to ordinary unconstrained routing, not the present root cause. Here the selected correction must reflect an LSP cannot follow an unavailable required hop. Test for: The backup LSP establishes on a permitted alternate path.

D:

This answer would be more suitable when a policy change unexpectedly makes a backup transit provider carry most outbound traffic, where the corrective action is to inspect local preference, export/import inheritance and selected BGP path attributes. The failure here is different: An LSP cannot follow an unavailable required hop. Required validation: The backup LSP establishes on a permitted alternate path.

Question 538

A port belongs to a VLAN but traffic to a remote site is forwarded through a different bridge domain. Which technical explanation and controlled action address the symptom?

  1. Cause: Nonstop bridging protects relevant Layer 2 control-protocol state during switchover. Response: Evaluate nonstop bridging together with the supported Routing Engine redundancy design.
  2. Diagnosis: Ethernet forwarding uses bridge-domain context rather than arbitrary IP-route matching. Action: Trace frame classification and virtual-switch bridge-domain association.
  3. Explanation: Bridges learn source MAC locations and flood unknown destinations within a permitted domain. Repair: Review MAC learning and unknown-unicast handling within the correct bridge domain.
  4. Fault mechanism: A trunk carries only its configured authorized VLANs. Remediation: Review allowed VLAN membership on both trunk endpoints.

Explanation

Correct Answer

B:

This is the model-intended best choice because ethernet forwarding uses bridge-domain context rather than arbitrary IP-route matching. The targeted correction is to trace frame classification and virtual-switch bridge-domain association. Validate it by observing that a tagged test frame reaches the approved remote port in the same domain.

Incorrect Answers

A:

Nonstop bridging protects relevant Layer 2 control-protocol state during switchover describes a neighboring protocol concern. In this case the controlling fact is ethernet forwarding uses bridge-domain context rather than arbitrary IP-route matching. A correct remediation would trace frame classification and virtual-switch bridge-domain association and demonstrate: A tagged test frame reaches the approved remote port in the same domain.

C:

That result would be useful for a different failure, namely: A provider switch receives an unknown destination MAC and a new engineer expects it to unicast to a random uplink. The current case specifically calls for: Trace frame classification and virtual-switch bridge-domain association. The required observed result is: A tagged test frame reaches the approved remote port in the same domain.

D:

This response would target a different source scenario: A trunk permits VLAN 110 but excludes VLAN 120 while users on VLAN 120 report isolation from the remote switch. It cannot establish the current acceptance requirement, which is: A tagged test frame reaches the approved remote port in the same domain. The relevant action is: Trace frame classification and virtual-switch bridge-domain association.

Question 539

A route reflector advertises routes to the wrong clients after a change in group membership. What remediation is most directly applicable?

  1. Next step: Review EBGP multihop transport reachability and session parameters.
  2. Corrective action: Review route-reflector client and cluster design, including loop-prevention attributes.
  3. Apply this control: Compare negotiated timers and protocol logs with routing-engine and packet conditions.
  4. Remediation: Verify compatible network and Hello parameters including mask where applicable.

Explanation

Correct Answer

B:

Underlying cause: Route reflection relies on correct client boundaries and originator or cluster tracking. Corrective action: review route-reflector client and cluster design, including loop-prevention attributes. Verify the outcome: A test prefix reaches permitted clients without cycling through reflector clusters.

Incorrect Answers

A:

The alternative addresses a multihop EBGP session is configured like a directly connected neighbor and never establishes across the transit hop, not the present root cause. Here the selected correction must reflect route reflection relies on correct client boundaries and originator or cluster tracking. Test for: A test prefix reaches permitted clients without cycling through reflector clusters.

C:

This option overlooks the decisive condition. Its supporting principle is aggressive liveness settings can magnify loss or processing delays, while this scenario depends on route reflection relies on correct client boundaries and originator or cluster tracking. Verify the correction with: A test prefix reaches permitted clients without cycling through reflector clusters.

D:

OSPF network-type and Hello compatibility can prevent adjacency formation describes a neighboring protocol concern. In this case the controlling fact is route reflection relies on correct client boundaries and originator or cluster tracking. A correct remediation would review route-reflector client and cluster design, including loop-prevention attributes and demonstrate: A test prefix reaches permitted clients without cycling through reflector clusters.

Question 540

After a maintenance window a configured customer static prefix is missing from active routes despite no syntax errors. Which combined repair and acceptance criterion is strongest?

  1. Implement: Compare withdrawal and blackhole behavior under a lab failure before changing the safety route. Verify: The test demonstrates loop prevention without advertising false service reachability.
  2. Control: Inspect the configuration, active route state and next-hop reachability before changing preference. Accepted result: The static route becomes active after the actual next-hop fault is corrected.
  3. Action: Confirm the configured local and peer AS values with the authoritative design. Evidence: The session reaches Established only with the documented correct peer AS.
  4. Repair: Review route preference before considering equivalent forwarding paths. Check: The selected path and its preference match the intended backup policy.

Explanation

Correct Answer

B:

Because operational route troubleshooting starts with active state and resolution evidence, the best response is to inspect the configuration, active route state and next-hop reachability before changing preference. A reviewer can close the technical case only after confirming that the static route becomes active after the actual next-hop fault is corrected.

Incorrect Answers

A:

That result would be useful for a different failure, namely: An engineer deletes an aggregate discard without first checking whether it prevents a transient routing loop. The current case specifically calls for: Inspect the configuration, active route state and next-hop reachability before changing preference. The required observed result is: The static route becomes active after the actual next-hop fault is corrected.

C:

Confirm the configured local and peer AS values with the authoritative design is a relevant step for the separate scenario in which a remote BGP neighbor uses a different AS number than configured and the session fails during OPEN negotiation. It does not directly fix this case. Instead inspect the configuration, active route state and next-hop reachability before changing preference; verify: The static route becomes active after the actual next-hop fault is corrected.

D:

The alternative addresses two static routes for the same prefix have unequal preferences and the operator expects both paths to share traffic, not the present root cause. Here the selected correction must reflect operational route troubleshooting starts with active state and resolution evidence. Test for: The static route becomes active after the actual next-hop fault is corrected.

Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests