mcAfee Secure Website
exam =5
exam =6

Exam Code: JN0-364

Exam Name: Service Provider Routing and Switching, Specialist (JNCIS-SP)

Certification Provider: Juniper

Juniper JN0-364 Questions & Answers

Reliable & Actual Study Materials for JN0-364 Exam Success

69 Questions & Answers with Testing Engine

"JN0-364: Service Provider Routing and Switching, Specialist (JNCIS-SP)" Testing Engine covers all the knowledge points of the real Juniper JN0-364 exam.

The latest actual JN0-364 Questions & Answers from Pass4sure. Everything you need to prepare and get best score at JN0-364 exam easily and quickly.

exam =7
Guarantee

Satisfaction Guaranteed

Pass4sure has a remarkable Juniper Candidate Success record. We're confident of our products and provide no hassle product exchange. That's how confident we are!

99.3% Pass Rate
Was: $137.49
Now: $124.99

Juniper JN0-364 Practice Test 3

Question 20

An iBGP route is hidden because the next hop learned from an edge router is unreachable inside the backbone. Which protocol behavior most directly determines the correct diagnosis?

  1. The key distinction is: Neighbor state must be traced through transport before modifying route policy.
  2. Protocol behavior: Unresolvable BGP next hops can make received routes unusable.
  3. Underlying principle: A usable IP path need not supply a suitable MPLS LSP or labeled transport path.
  4. Root design issue: EBGP speakers separated by intermediate devices require deliberate transport reachability and hop policy.

Explanation

Correct Answer

B:

Because unresolvable BGP next hops can make received routes unusable, the best response is to restore appropriate IGP next-hop reachability or approved next-hop-self behavior. A reviewer can close the technical case only after confirming that the internal router resolves the next hop and installs the intended route.

Incorrect Answers

A:

That result would be useful for a different failure, namely: A BGP peer is stuck in Active after a maintenance window even though the remote address is configured. The current case specifically calls for: Restore appropriate IGP next-hop reachability or approved next-hop-self behavior. The required observed result is: The internal router resolves the next hop and installs the intended route.

C:

Inspect label-switched next-hop resolution separately from generic IP reachability is a relevant step for the separate scenario in which a loopback loses its MPLS-resolvable route but ordinary IP routing to the loopback remains reachable. It does not directly fix this case. Instead restore appropriate IGP next-hop reachability or approved next-hop-self behavior; verify: The internal router resolves the next hop and installs the intended route.

D:

The alternative addresses a multihop EBGP session is configured like a directly connected neighbor and never establishes across the transit hop, not the present root cause. Here the selected correction must reflect unresolvable BGP next hops can make received routes unusable. Test for: The internal router resolves the next hop and installs the intended route.

Question 21

An input firewall filter diverts all transit traffic to a management routing instance by mistake. Which corrective action and confirmation pair is most appropriate?

  1. Change: Coordinate authentication parameters and test the key change under maintenance controls. Test: Authenticated adjacency returns and no fallback to unauthenticated operation occurs.
  2. Implement: Narrow filter match terms and validate filter-based forwarding for both matched and unmatched probes. Verify: Only approved traffic uses the alternate table while ordinary transit remains on its path.
  3. Control: Document the discard behavior and determine whether the aggregate should remain advertised. Accepted result: Loss-of-specific-route testing produces the approved withdrawal or discard outcome.
  4. Action: Restore the intended route preferences and check selected forwarding next hops. Evidence: A primary-link test chooses the expected primary then fails to backup on loss.

Explanation

Correct Answer

B:

The case turns on the distinction that filter-based routing policy requires explicit match conditions and a safe default behavior. Apply this concrete engineering step: Narrow filter match terms and validate filter-based forwarding for both matched and unmatched probes. An acceptable verification outcome is: Only approved traffic uses the alternate table while ordinary transit remains on its path.

Incorrect Answers

A:

This option overlooks the decisive condition. Its supporting principle is authentication mismatches can reject otherwise valid OSPF protocol packets, while this scenario depends on filter-based routing policy requires explicit match conditions and a safe default behavior. Verify the correction with: Only approved traffic uses the alternate table while ordinary transit remains on its path.

C:

The proposed principle concerns another network fault: A discard summary can prevent loops but can blackhole traffic when reachability assumptions are wrong. Here, filter-based routing policy requires explicit match conditions and a safe default behavior. The most direct correction is to narrow filter match terms and validate filter-based forwarding for both matched and unmatched probes, confirmed by only approved traffic uses the alternate table while ordinary transit remains on its path.

D:

That result would be useful for a different failure, namely: A backup path becomes primary after a preference edit even though the design called for failover only. The current case specifically calls for: Narrow filter match terms and validate filter-based forwarding for both matched and unmatched probes. The required observed result is: Only approved traffic uses the alternate table while ordinary transit remains on its path.

Question 22

An engineer modifies BGP keepalive or hold timers and the session flaps during CPU pressure. What observable result most directly verifies the intended configuration?

  1. Verification result: A controlled route lookup confirms the neighbor's actual selected entry path.
  2. Closeout evidence: The transit LSR selects an authorized outgoing label and interface.
  3. Acceptance check: The restored session remains stable while meeting the approved detection target.
  4. The test confirms that the approved route matches an accepting term and the denied route remains denied.

Explanation

Correct Answer

C:

Because aggressive liveness settings can magnify loss or processing delays, the best response is to compare negotiated timers and protocol logs with routing-engine and packet conditions. A reviewer can close the technical case only after confirming that the restored session remains stable while meeting the approved detection target.

Incorrect Answers

A:

Distinguish an advertised inbound hint from neighboring-AS route policy decisions is a relevant step for the separate scenario in which an inbound MED is assumed to control outgoing traffic even though the receiving network has its own path-selection policies. It does not directly fix this case. Instead compare negotiated timers and protocol logs with routing-engine and packet conditions; verify: The restored session remains stable while meeting the approved detection target.

B:

The alternative addresses a provider assumes an ordinary IP destination lookup and an MPLS label lookup always use the same forwarding table, not the present root cause. Here the selected correction must reflect aggressive liveness settings can magnify loss or processing delays. Test for: The restored session remains stable while meeting the approved detection target.

D:

This option overlooks the decisive condition. Its supporting principle is policy evaluation order can short-circuit later intended acceptance, while this scenario depends on aggressive liveness settings can magnify loss or processing delays. Verify the correction with: The restored session remains stable while meeting the approved detection target.

Question 23

After a trunk change a MAC address is visible but only one of two VLANs can traverse the uplink. What diagnosis and engineering response are most appropriate?

  1. Cause: Traditional spanning-tree root election favors the lowest bridge ID. Response: Review root bridge priority and MAC-based bridge identifier comparison.
  2. Diagnosis: IRB depends on both L2 membership and a valid L3 gateway configuration. Action: Verify VLAN-to-IRB interface binding, addresses and active route entries.
  3. Explanation: Layer 2 isolation depends on bridge-domain and logical switch boundaries. Repair: Separate customer bridge domains and validate virtual-switch membership.
  4. Fault mechanism: MAC table visibility alone does not prove trunk authorization for every VLAN. Remediation: Inspect VLAN membership and tagging on both ends and verify per-VLAN MAC learning.

Explanation

Correct Answer

D:

Underlying cause: MAC table visibility alone does not prove trunk authorization for every VLAN. Corrective action: inspect VLAN membership and tagging on both ends and verify per-VLAN MAC learning. Verify the outcome: Separate tagged tests pass in both permitted VLANs.

Incorrect Answers

A:

The proposed principle concerns another network fault: Traditional spanning-tree root election favors the lowest bridge ID. Here, mAC table visibility alone does not prove trunk authorization for every VLAN. The most direct correction is to inspect VLAN membership and tagging on both ends and verify per-VLAN MAC learning, confirmed by separate tagged tests pass in both permitted VLANs.

B:

That result would be useful for a different failure, namely: A router-on-a-stick replacement with IRB stops reachability between a bridge domain and an L3 subnet. The current case specifically calls for: Inspect VLAN membership and tagging on both ends and verify per-VLAN MAC learning. The required observed result is: Separate tagged tests pass in both permitted VLANs.

C:

This response would target a different source scenario: A customer bridge-domain spans two isolated customers due to reusing a virtual switch without tenant boundaries. It cannot establish the current acceptance requirement, which is: Separate tagged tests pass in both permitted VLANs. The relevant action is: Inspect VLAN membership and tagging on both ends and verify per-VLAN MAC learning.

Question 24

A BGP peer is stuck in Active after a maintenance window even though the remote address is configured. What should the operations engineer do first to address the stated fault?

  1. Next step: Check the expected DR/BDR versus DROther neighbor-state relationships.
  2. Corrective action: Trace the applicable BGP route-selection steps and local policies.
  3. Apply this control: Inspect effective group and neighbor export policy evaluation order.
  4. Remediation: Verify IP reachability, routing instance context, TCP transport and session authentication.

Explanation

Correct Answer

D:

Because neighbor state must be traced through transport before modifying route policy, the best response is to verify IP reachability, routing instance context, TCP transport and session authentication. A reviewer can close the technical case only after confirming that the TCP peering session reaches Established and remains stable.

Incorrect Answers

A:

This answer would be more suitable when an engineer assumes both routers must reach Full with every speaker on a broadcast network, where the corrective action is to check the expected DR/BDR versus DROther neighbor-state relationships. The failure here is different: Neighbor state must be traced through transport before modifying route policy. Required validation: The TCP peering session reaches Established and remains stable.

B:

This option overlooks the decisive condition. Its supporting principle is bGP selection is policy-driven and is not equivalent to IGP least-hop routing, while this scenario depends on neighbor state must be traced through transport before modifying route policy. Verify the correction with: The TCP peering session reaches Established and remains stable.

C:

Policy inheritance and term action order affect BGP route advertisement describes a neighboring protocol concern. In this case the controlling fact is neighbor state must be traced through transport before modifying route policy. A correct remediation would verify IP reachability, routing instance context, TCP transport and session authentication and demonstrate: The TCP peering session reaches Established and remains stable.

Question 25

An ingress LSP shows up but transit packets are dropped after one router swaps to an unexpected label. Which next action best resolves this observed routing or switching failure?

  1. Recommended change: Distinguish IP RIB entries from label forwarding information and LSP resolution.
  2. Next step: Collect hop-local LFIB, label forwarding and interface counters along the LSP.
  3. Corrective action: Inspect the incoming label, outgoing label and interface on each affected LSR.
  4. Apply this control: Distinguish an advertised inbound hint from neighboring-AS route policy decisions.

Explanation

Correct Answer

C:

The critical observation is: Label-switching errors can occur even when control-plane endpoint reachability is good. Correct it by taking this action: Inspect the incoming label, outgoing label and interface on each affected LSR. Confirm the outcome with: The repaired hop has the expected swap operation and carries a test packet.

Incorrect Answers

A:

This response would target a different source scenario: A provider assumes an ordinary IP destination lookup and an MPLS label lookup always use the same forwarding table. It cannot establish the current acceptance requirement, which is: The repaired hop has the expected swap operation and carries a test packet. The relevant action is: Inspect the incoming label, outgoing label and interface on each affected LSR.

B:

Collect hop-local LFIB, label forwarding and interface counters along the LSP is a relevant step for the separate scenario in which a maintenance change affects MPLS forwarding on just one core hop and the team only checks RSVP session status at ingress. It does not directly fix this case. Instead inspect the incoming label, outgoing label and interface on each affected LSR; verify: The repaired hop has the expected swap operation and carries a test packet.

D:

This answer would be more suitable when an inbound MED is assumed to control outgoing traffic even though the receiving network has its own path-selection policies, where the corrective action is to distinguish an advertised inbound hint from neighboring-AS route policy decisions. The failure here is different: Label-switching errors can occur even when control-plane endpoint reachability is good. Required validation: The repaired hop has the expected swap operation and carries a test packet.

Question 26

Two routers advertise identical OSPF router IDs and their link-state information becomes inconsistent. What operational check demonstrates that the intended outcome occurred?

  1. Closeout evidence: Each router is uniquely identified and the link-state database converges.
  2. Acceptance check: The intended lower-total-cost path wins under steady-state conditions.
  3. The test confirms that the corrected link reaches stable Full adjacency and exchanges the intended routes.
  4. Expected observation: The rollback and candidate checks show the exact intended RIB and FIB outcomes.

Explanation

Correct Answer

A:

Because oSPF identifies speakers by router ID, which must be unique inside a routing domain, the best response is to assign distinct stable router IDs and clear stale protocol state using an approved procedure. A reviewer can close the technical case only after confirming that each router is uniquely identified and the link-state database converges.

Incorrect Answers

B:

The proposed principle concerns another network fault: OSPF normally prefers the least accumulated metric to a destination. Here, oSPF identifies speakers by router ID, which must be unique inside a routing domain. The most direct correction is to assign distinct stable router IDs and clear stale protocol state using an approved procedure, confirmed by each router is uniquely identified and the link-state database converges.

C:

That result would be useful for a different failure, namely: A new OSPF uplink remains down at the adjacency stage after a router replacement. The current case specifically calls for: Assign distinct stable router IDs and clear stale protocol state using an approved procedure. The required observed result is: Each router is uniquely identified and the link-state database converges.

D:

This response would target a different source scenario: A policy adjustment changes both routing preference and forwarding instance selection in one unreviewed commit. It cannot establish the current acceptance requirement, which is: Each router is uniquely identified and the link-state database converges. The relevant action is: Assign distinct stable router IDs and clear stale protocol state using an approved procedure.

Question 27

A customer bridge-domain spans two isolated customers due to reusing a virtual switch without tenant boundaries. What is the most defensible network engineering correction?

  1. Apply this control: Separate customer bridge domains and validate virtual-switch membership.
  2. Remediation: Trace Layer 2 topology, learned MACs and spanning-tree or Ethernet loop defenses.
  3. Recommended change: Enable the appropriate spanning-tree protection and verify the blocked redundant path.
  4. Next step: Review allowed VLAN membership on both trunk endpoints.

Explanation

Correct Answer

A:

The case turns on the distinction that layer 2 isolation depends on bridge-domain and logical switch boundaries. Apply this concrete engineering step: Separate customer bridge domains and validate virtual-switch membership. An acceptable verification outcome is: A cross-customer unknown-unicast probe remains isolated from the other tenant.

Incorrect Answers

B:

This answer would be more suitable when an operator tries to solve a MAC-learning loop by adding a static IP route in the core, where the corrective action is to trace Layer 2 topology, learned MACs and spanning-tree or Ethernet loop defenses. The failure here is different: Layer 2 isolation depends on bridge-domain and logical switch boundaries. Required validation: A cross-customer unknown-unicast probe remains isolated from the other tenant.

C:

This option overlooks the decisive condition. Its supporting principle is spanning tree prevents forwarding loops by selecting a loop-free active topology, while this scenario depends on layer 2 isolation depends on bridge-domain and logical switch boundaries. Verify the correction with: A cross-customer unknown-unicast probe remains isolated from the other tenant.

D:

A trunk carries only its configured authorized VLANs describes a neighboring protocol concern. In this case the controlling fact is layer 2 isolation depends on bridge-domain and logical switch boundaries. A correct remediation would separate customer bridge domains and validate virtual-switch membership and demonstrate: A cross-customer unknown-unicast probe remains isolated from the other tenant.

Question 28

A service provider tunnels IPv6 over an IPv4 core but expects native IPv6 forwarding at every transit hop. Which change best corrects the failure without losing the intended design?

  1. Corrective action: Distinguish tunneling encapsulation from confidentiality protection.
  2. Apply this control: Confirm the IPv6 next-hop adjacency and active routing entry.
  3. Remediation: Validate IPv6 addressing, neighbor discovery and inet6 routing separately.
  4. Recommended change: Model endpoint encapsulation and decapsulation for IPv6-over-IPv4 transport.

Explanation

Correct Answer

D:

Correct diagnosis: Tunneling carries one protocol over an underlay that may not route that payload natively. The appropriate action is: Model endpoint encapsulation and decapsulation for IPv6-over-IPv4 transport. The follow-up evidence required is: A tunnel packet is carried over IPv4 and decapsulated to IPv6 at the endpoint.

Incorrect Answers

A:

That result would be useful for a different failure, namely: A network operator assumes a GRE tunnel encrypts customer packets merely because they are encapsulated. The current case specifically calls for: Model endpoint encapsulation and decapsulation for IPv6-over-IPv4 transport. The required observed result is: A tunnel packet is carried over IPv4 and decapsulated to IPv6 at the endpoint.

B:

This response would target a different source scenario: A router has an IPv6 default route but no usable next-hop reachability on the egress link. It cannot establish the current acceptance requirement, which is: A tunnel packet is carried over IPv4 and decapsulated to IPv6 at the endpoint. The relevant action is: Model endpoint encapsulation and decapsulation for IPv6-over-IPv4 transport.

C:

Validate IPv6 addressing, neighbor discovery and inet6 routing separately is a relevant step for the separate scenario in which a new Junos edge router can ping IPv4 customers but cannot route IPv6 traffic to the same site. It does not directly fix this case. Instead model endpoint encapsulation and decapsulation for IPv6-over-IPv4 transport; verify: A tunnel packet is carried over IPv4 and decapsulated to IPv6 at the endpoint.

Question 29

An area border router stops advertising an expected summarized interarea route after a policy change. What implementation step and validation result should be selected?

  1. Control: Inspect ABR area configuration, route export rules and summary policy. Accepted result: The correct summarized route appears in the receiving area's route table.
  2. Action: Compare received LSAs with route selection, area eligibility and next-hop resolution. Evidence: The routing table exposes the selection reason and the intended route is installed.
  3. Repair: Restore the intended route preferences and check selected forwarding next hops. Check: A primary-link test chooses the expected primary then fails to backup on loss.
  4. Change: Revisit additive path cost and verify SPF outcomes across alternative links. Test: The intended lower-total-cost path wins under steady-state conditions.

Explanation

Correct Answer

A:

The critical observation is: Interarea reachability depends on the ABR's view and allowed advertisements. Correct it by taking this action: Inspect ABR area configuration, route export rules and summary policy. Confirm the outcome with: The correct summarized route appears in the receiving area's route table.

Incorrect Answers

B:

Receiving topology data does not guarantee a route becomes active and installed describes a neighboring protocol concern. In this case the controlling fact is interarea reachability depends on the ABR's view and allowed advertisements. A correct remediation would inspect ABR area configuration, route export rules and summary policy and demonstrate: The correct summarized route appears in the receiving area's route table.

C:

The proposed principle concerns another network fault: Preference edits can change route selection without any interface outage. Here, interarea reachability depends on the ABR's view and allowed advertisements. The most direct correction is to inspect ABR area configuration, route export rules and summary policy, confirmed by the correct summarized route appears in the receiving area's route table.

D:

That result would be useful for a different failure, namely: A branch uses a higher OSPF interface cost but expects that branch to remain the preferred primary path. The current case specifically calls for: Inspect ABR area configuration, route export rules and summary policy. The required observed result is: The correct summarized route appears in the receiving area's route table.

Question 30

A BGP prefix remains rejected after an intended route filter update because an earlier term rejects it. What diagnosis and engineering response are most appropriate?

  1. Fault mechanism: Policy evaluation order can short-circuit later intended acceptance. Remediation: Evaluate policy terms in effective order and test matching routes.
  2. Root issue: Unresolvable BGP next hops can make received routes unusable. Correction: Restore appropriate IGP next-hop reachability or approved next-hop-self behavior.
  3. Cause: BGP message types have separate roles in session formation and reachability exchange. Response: Distinguish session negotiation from UPDATE message route advertisements.
  4. Diagnosis: OSPF broadcast topology reduces unnecessary full adjacency mesh formation. Action: Check the expected DR/BDR versus DROther neighbor-state relationships.

Explanation

Correct Answer

A:

Correct diagnosis: Policy evaluation order can short-circuit later intended acceptance. The appropriate action is: Evaluate policy terms in effective order and test matching routes. The follow-up evidence required is: The approved route matches an accepting term and the denied route remains denied.

Incorrect Answers

B:

The alternative addresses an iBGP route is hidden because the next hop learned from an edge router is unreachable inside the backbone, not the present root cause. Here the selected correction must reflect policy evaluation order can short-circuit later intended acceptance. Test for: The approved route matches an accepting term and the denied route remains denied.

C:

This answer would be more suitable when a provider engineer treats a BGP OPEN message as if it already advertises reachable customer prefixes, where the corrective action is to distinguish session negotiation from UPDATE message route advertisements. The failure here is different: Policy evaluation order can short-circuit later intended acceptance. Required validation: The approved route matches an accepting term and the denied route remains denied.

D:

This option overlooks the decisive condition. Its supporting principle is oSPF broadcast topology reduces unnecessary full adjacency mesh formation, while this scenario depends on policy evaluation order can short-circuit later intended acceptance. Verify the correction with: The approved route matches an accepting term and the denied route remains denied.

Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests