mcAfee Secure Website
exam =5
exam =6

Exam Code: IC34 ISA-IEC 62443 Cybersecurity Design Specialist

Exam Name: IC34 ISA-IEC 62443 Cybersecurity Design Specialist

Certification Provider: ISA

ISA IC34 ISA-IEC 62443 Cybersecurity Design Specialist Questions & Answers

Reliable & Actual Study Materials for IC34 ISA-IEC 62443 Cybersecurity Design Specialist Exam Success

100 Questions & Answers with Testing Engine

"IC34 ISA-IEC 62443 Cybersecurity Design Specialist: IC34 ISA-IEC 62443 Cybersecurity Design Specialist" Testing Engine covers all the knowledge points of the real ISA IC34 ISA-IEC 62443 Cybersecurity Design Specialist exam.

The latest actual IC34 ISA-IEC 62443 Cybersecurity Design Specialist Questions & Answers from Pass4sure. Everything you need to prepare and get best score at IC34 ISA-IEC 62443 Cybersecurity Design Specialist exam easily and quickly.

exam =7
Guarantee

Satisfaction Guaranteed

Pass4sure has a remarkable ISA Candidate Success record. We're confident of our products and provide no hassle product exchange. That's how confident we are!

99.3% Pass Rate
Was: $137.49
Now: $124.99

ISA IC34 ISA-IEC 62443 Cybersecurity Design Specialist Practice Test 10

Question 90

A system review identifies that an external integrator's account remains active long after the commissioning contract ends. Select TWO: a suitable action and its direct acceptance evidence.

  1. Operators retain a safe break-glass path without leaving permanent bypass credentials
  2. Automate expiration and periodic recertification of supplier identities
  3. The expired identity cannot start new remote sessions
  4. Constrain the brokered session to the approved service and endpoints

Explanation

Correct Answers

B:

This change addresses the stated weakness because supplier access rights should follow contract and task lifecycle. Confirm the result by checking that the expired identity cannot start new remote sessions.

C:

The acceptance result directly demonstrates the requirement has been met. The enabling measure is to automate expiration and periodic recertification of supplier identities; supplier access rights should follow contract and task lifecycle.

Incorrect Answers

A:

This check belongs to Dual-factor failure plan. For the current issue, acceptance should establish that the expired identity cannot start new remote sessions.

D:

Session protocol limitation is a separate issue; in this design, supplier access rights should follow contract and task lifecycle.

Question 91

Which technical principle best explains the design concern where a turbine safety shutdown relies on a time source hosted on an unprotected office server?

  1. Risk assessments must cover supporting services and common-mode dependencies
  2. Risk likelihood depends on actual connectivity and threat pathways
  3. Attack-path analysis examines reachable sequences rather than individual devices alone
  4. Threat scenarios make risk findings actionable at asset and conduit level

Explanation

Correct Answer

A:

This concept explains why the control is needed: risk assessments must cover supporting services and common-mode dependencies. Implementation can be checked by confirming that a test isolates the office network without disrupting required turbine event sequencing.

Incorrect Answers

B:

Risk assessments must cover supporting services and common-mode dependencies. The option describes a different kind of control.

C:

Attack path review is a different problem; the relevant mechanism here is that risk assessments must cover supporting services and common-mode dependencies.

D:

This principle applies to Threat scenario linkage, such as when a chemical plant calls ransomware high risk but its design record never identifies which control servers could be affected. The current case depends on the concept that risk assessments must cover supporting services and common-mode dependencies.

Question 92

During an OT architecture review, a remote field cabinet has exposed console ports reachable from a public corridor. What is the most targeted corrective approach?

  1. Disable or filter unnecessary configuration services and interfaces
  2. Create vendor-approved application control and tested scanning exclusions
  3. Store a protected baseline and verified rollback procedure before modifications
  4. Restrict physical console access and audit maintenance visits

Explanation

Correct Answer

D:

The proposed control has a clear operational purpose: physical protection is part of system hardening. Its acceptance evidence is that an unauthorized visitor cannot reach the controller console.

Incorrect Answers

A:

Unneeded industrial ports is a separate issue; in this design, physical protection is part of system hardening.

B:

The measure is relevant when an antivirus product quarantines live DCS runtime files because industrial vendor exclusions were not reviewed, but it does not address the fact that network controls cannot prevent direct physical console misuse.

C:

That step responds to Configuration backup, not the reported issue. Here the relevant design principle is that physical protection is part of system hardening.

Question 93

Which TWO choices form a sound engineering response and acceptance check for a situation where virtualized HMI and historian guests share one unrestricted hypervisor vSwitch?

  1. Design a dedicated and prioritized intersite conduit with distinct access rules
  2. HMI-to-historian traffic follows only approved virtual paths
  3. Assign appropriate virtual security zones and enforce guest-to-guest restrictions
  4. Guest exposure does not grant an unrestricted route to programming interfaces

Explanation

Correct Answers

B:

This observation tests the intended change: assign appropriate virtual security zones and enforce guest-to-guest restrictions. It matters because segmentation must be enforced inside virtual networks too.

C:

The proposed control has a clear operational purpose: segmentation must be enforced inside virtual networks too. Its acceptance evidence is that hMI-to-historian traffic follows only approved virtual paths.

Incorrect Answers

A:

That step responds to Cross-site replication, not the reported issue. Here the relevant design principle is that segmentation must be enforced inside virtual networks too.

D:

This observation comes from Engineering workstation zone, a separate industrial condition. It does not prove the required result: hMI-to-historian traffic follows only approved virtual paths.

Question 94

For this operational problem, a workstation security patch is deployed to the DCS without testing vendor driver compatibility, what foundational design concept is relevant?

  1. Portable-media control is essential where offline maintenance is routine
  2. OT patch management balances vulnerability reduction with operational stability
  3. Credential hardening starts with removal of insecure defaults
  4. Management protocols require confidentiality and identity controls

Explanation

Correct Answer

B:

This mechanism is the basis of the design decision. If ignored, untested patches can interrupt critical control applications.

Incorrect Answers

A:

This principle applies to Portable media policy, such as when operators use arbitrary USB drives to transfer logic to safety controllers. The current case depends on the concept that oT patch management balances vulnerability reduction with operational stability.

C:

OT patch management balances vulnerability reduction with operational stability. The option describes a different kind of control.

D:

Secure switch management is a different problem; the relevant mechanism here is that oT patch management balances vulnerability reduction with operational stability.

Question 95

A commissioning review notes that a security team proposes aggressive active vulnerability scans during live turbine operation to detect threats. Which engineering response best fits the concern?

  1. Use approved passive traffic sensing or carefully scheduled safe assessment
  2. Use compatible industrial protocol inspection for restricted command functions
  3. Validate capture capacity and use supported taps or carefully scoped mirroring
  4. Position sensors to observe the relevant industrial conduits safely

Explanation

Correct Answer

A:

This change addresses the stated weakness because passive observation can reduce the operational risk of traffic analysis. Confirm the result by checking that sensor discovery identifies expected device traffic without controller instability.

Incorrect Answers

B:

This measure is useful for Protocol-aware alert, where an IDS sees all Modbus TCP as normal port 502 traffic and ignores unexpected write functions. In the present case, intrusive probing can disrupt fragile industrial equipment; the targeted response is different.

C:

The measure is relevant when a switch SPAN port drops mirrored packets because the combined source traffic exceeds its capacity, but it does not address the fact that intrusive probing can disrupt fragile industrial equipment.

D:

That step responds to Sensor location, not the reported issue. Here the relevant design principle is that passive observation can reduce the operational risk of traffic analysis.

Question 96

Which risk should the designer prioritize in this scenario: an oil terminal prioritizes easy-to-fix low-impact HMI cosmetic findings over a severe remote command exposure?

  1. A security measure can introduce unacceptable operational hazards
  2. A cosmetic-finding backlog can displace mitigation of major hazards
  3. Engineering may silently accept risk beyond management tolerance
  4. Unmodeled pivots can bypass a seemingly segmented architecture

Explanation

Correct Answer

B:

The scenario exposes this outcome because design investment should focus on consequential residual risks. The intended treatment is to rank remediation by impact, exposure, and existing protection rather than convenience.

Incorrect Answers

A:

That concern does not address the immediate risk: a cosmetic-finding backlog can displace mitigation of major hazards.

C:

It would matter for Tolerance decision; the reported weakness instead threatens that a cosmetic-finding backlog can displace mitigation of major hazards.

D:

This describes the separate issue of Attack path review. For the current system, design investment should focus on consequential residual risks.

Question 97

Which risk should the designer prioritize in this scenario: a commissioning contractor discards signed test results after project acceptance?

  1. Lost evidence prevents later assurance and controlled maintenance
  2. Undocumented integrations undermine boundary controls
  3. Obsolete security devices can become unpatchable before the process retires
  4. Misclassified defects may ship into safety-critical environments

Explanation

Correct Answer

A:

This is the relevant failure mode for the described process. secure engineering depends on preserved configuration and verification records. Reduce exposure by taking this step: define retention and handover for cybersecurity design and test artifacts.

Incorrect Answers

B:

It would matter for Interface contract; the reported weakness instead threatens that lost evidence prevents later assurance and controlled maintenance.

C:

This failure can arise in Product selection longevity, for example where a proposed industrial firewall model is entering end of maintenance while plant life is ten years. Here the direct exposure is that lost evidence prevents later assurance and controlled maintenance.

D:

This describes the separate issue of Security defect handling. For the current system, secure engineering depends on preserved configuration and verification records.

Question 98

For an IACS condition where a new MES-to-SCADA link appears in the topology but not in the requirements specification, what underlying security concept applies?

  1. Identification and authentication are distinct from granting permissions
  2. Conduit requirements must identify authorized flows and their operating context
  3. Cybersecurity requirements must accommodate verified IACS safety and availability needs
  4. Recoverability requirements must describe measurable business and process outcomes

Explanation

Correct Answer

B:

This mechanism is the basis of the design decision. If ignored, unrecorded interfaces undermine segmentation acceptance.

Incorrect Answers

A:

Authentication requirement is a different problem; the relevant mechanism here is that conduit requirements must identify authorized flows and their operating context.

C:

This is relevant to Operational constraints but does not explain the stated process issue. The correct design rationale is that conduit requirements must identify authorized flows and their operating context.

D:

Conduit requirements must identify authorized flows and their operating context. The option describes a different kind of control.

Question 99

A site implementation finds that a legacy field protocol cannot tolerate added encryption latency but the CRS requires it without analysis. Select TWO statements representing the correction and its confirming test.

  1. Define trust anchors, enrollment, renewal, revocation, and failure response
  2. Document approved alternative safeguards and performance constraints
  3. The accepted design controls the conduit without exceeding scan-cycle limits
  4. Different zones show traceable treatment appropriate to their assessed risk

Explanation

Correct Answers

B:

Confidentiality measures should be selected with process timing and compatibility in mind. Confirm completion when the accepted design controls the conduit without exceeding scan-cycle limits.

C:

The evidence links the outcome to the security mechanism: confidentiality measures should be selected with process timing and compatibility in mind. The corresponding design step is to document approved alternative safeguards and performance constraints.

Incorrect Answers

A:

Certificate lifecycle is a separate issue; in this design, confidentiality measures should be selected with process timing and compatibility in mind.

D:

This check belongs to Security level mapping. For the current issue, acceptance should establish that the accepted design controls the conduit without exceeding scan-cycle limits.

Question 100

A system has this condition: a facility buys certified devices but has no site-wide account management or change governance. Which principle explains the appropriate treatment?

  1. Part 2-1 concerns asset-owner security program responsibilities
  2. Security level claims require appropriately scoped multi-control evidence
  3. Conduits require security controls matching the communication risk
  4. Part 3-3 specifies system technical security requirements and levels

Explanation

Correct Answer

A:

This mechanism is the basis of the design decision. If ignored, secure hardware alone cannot sustain consistent operational protection.

Incorrect Answers

B:

This principle applies to Security level verification, such as when an integrator checks only password policy and declares that every foundational category meets its target. The current case depends on the concept that part 2-1 concerns asset-owner security program responsibilities.

C:

This is relevant to Conduit-specific control but does not explain the stated process issue. The correct design rationale is that part 2-1 concerns asset-owner security program responsibilities.

D:

System requirements standard is a different problem; the relevant mechanism here is that part 2-1 concerns asset-owner security program responsibilities.

IC34 ISA-IEC 62443 Cybersecurity Design Specialist Practice Tests